1. Before You Start Package Contests +TEW-821DAP ~Quick Installation Guide notwork cable (1.
2. Quick Reference Nita; By default, the wireless network nama/SSID and wireless encryption settings have been per-configured for your convenience and can be located on the Included preset wireless settings sticker or on the device label located on the back of the access point.
3. Hardware Installation and Configuration g Mot It | strongly recommends to configure the access point first before mounting. 1. Connect a network cable from the network LAN port of your access point to your computer. 2. Connect the Included power adapter from a power outset to your access point power port. 3. Push the Power On/0ff switch to tum on the access point. 4.The Power (PW, LAN, GHz and 2.
5. Assign a static IP address to your computer's network adapter In the subset of 182.168.10.x {0.9.192.158.10.25) and subset mask of 255.255.255.0. oke: For more information on assigning a static IP address to your computer's network adapter, please refer to stem Q1 In the last section of the Installation goods, Installation Tips and Troubleshooting. 6. Open your weh browser, type the default URL or default IP address of the wireless access port in the address bar, and then press Infer.
9, To configure your wireless network nameless and wireless encryption settings, click the wireless band you would elks to configure Wireless 2.46Hz or Wireless Shiraz and click on Wireless Network. Mots: By default, the wireless network nameless and wireless encryption has been reconfigured for your convenience and can be located on the included wireless settings sticker or on the device label located on the back of the access port.
12. To change the wireless encryption key for the selected wireless band, under WPA, enter the new encryption key In the Pr-Shared Key fled. Click Save at the bottom of the page to temporarily save the settings. 13. In the top left man menu, click Apply/Discard Changes and click on Save & Apply to save & commit the configuration changes. Important Note: Configuration changes In the access point web management configuration ars not appalled until you permanently Awe & Apply under Apply/Dizcard Changes.
15. Under LAN Connection type, click the Connection Type drop-down list to select either DH (default setting) or STATIC. Selecting CPD will set your access point to obtain IP address tastings automatically from a BHOPAL server on your network and selecting STATIC will allow you to manually assign your access point IP address settings fo meet the IP requirements of your network.
17. To mount the access point, first route the network cable through the largest opening In the mounting placenta and Ina tall the mounting plats to the desired wall or excelling using the included drywall anchors and screws. Install the mounting plate with the clips facing away from the wall or calling. if wall mounting, Install the mounting plate with the correct orientation.
Mounting Plate {Orientation for wall mounting) To download the latest version of the user's glued, please go to com/support and aspect the TEW-821DAP H/W: v2.
Installation Tips and Troubleshooting Q1: How do | configure my computer's network adapter with a sciatic IP address? Hots: Oases onto that though the following procedures are provided to follow for your operating system network adapter settings to be used as general guidelines, however, iris strongly recommended that you consult your computer or operating system manufacturer directly for assistance on the proper provocateur for configuring network tastings.
02: 1 configured my computer's network adapter with a static IP address, how da | Configurations my computer's network adapter to default settings and obtain an IP address automatically using CPD? Note: Please note that although the following procedures are provided to follow for your operating system network adapter settings to be used as general guidelines, however, It Is strongly recommended that you consult your computer o operating system manufacturer directly for assistance on the proper procedure for
03: 1 typed In my Interment Browser Address Bag, but an emir massage says “The page cannot be displayed” How can | access the wireless access palmtop management page? 1. Double check all physical cable and port connections. 2. Marks aura the LED on the wireless access point front panel are on. 3. Make sure your computer's network adapter Is configured with a static IP address. (Refer 1o Q1 for Instructions on assigning a static IP address).
MACROCOSM 1. Navigates to your Applications folder and open Limitless. 2. Double-click on Terminal to launch the command prompt. 3. In the command prompt, type Configure intifada
