TRENDnet User’s Guide Cover Page
TRENDnet User’s Guide Table of Contents Product Overview ...........................................................................1 Package Contents .......................................................................................................... 1 Features ......................................................................................................................... 1 Product Hardware Features...........................................................................................
TRENDnet User’s Guide Table of Contents Configure parameters for RMON events ........................................................... 68 Configure MLD Snooping Port Settings.............................................................. 42 Configure MLD Snooping Address Entry ............................................................ 43 Configure MLD Snooping Profile Settings .......................................................... 43 Voice VLAN .....................................................
TRENDnet User’s Guide Table of Contents Upgrade your switch firmware .................................................................................... 91 Firmware Upgrade via HTTP Settings ................................................................ 91 Firmware Upgrade via TFTP Settings ................................................................. 92 Backup and restore your switch configuration settings .............................................. 92 Backup/Restore via HTTP Settings .........
TRENDnet User’s Guide TEG-30102WS Features Product Overview TRENDnet’s 10-Port 2.5GBASE-T Web Smart+ Switch with eight 2.5GBASE-T ports and two 10G SFP+ slots, model TEG-30102WS, delivers advanced management features with an 80Gbps switching capacity. The TEG-30102WS is equipped with 2.5GBASE-T RJ-45 ports that provide higher gigabit speeds capable of up to 2.5Gbps over existing Cat5e or better cabling. This rack mountable IPv6 ready switch comes with an intuitive web-based interface.
TRENDnet User’s Guide TEG-30102WS Product Hardware Features Rear View Smart Fans AC Power Connector AC Power Connector – Connect the AC power cord to the connector and the other side into a power outlet. (Input: 100~240VAC, 50/60Hz) Reset Button – Press and hold this button for 10 seconds and release to reset the switch to factory defaults. The System LED will flash rapidly (orange) and turn solid (orange) to indicate the reset procedure was successful.
TRENDnet User’s Guide TEG-30102WS Diagnostic LED Indicators Power LED the Power LED lights on, the device is receiving On : When power. the Power turns off or the power cord is not Off : When connected On (Green) : On (Orange) : On (Green) : Solid – Device is connected at 2.5G speed. Blinking – Data transmission/activity at 2.5G speed. On (Orange) : Solid – Device is connected at 1G/100Mbps speed. Blinking – Data transmission/activity at 1G/100Mbps speed.
TRENDnet User’s Guide TEG-30102WS Application Diagram The WebSmart switch is installed a server room within an EIA standard-size, 19-inch rack The 2.5G web smart switch is providing 2.5G connectivity and VLAN support to existing network infrastructure. © Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEG-30102WS Switch Installation Rack Mount Hardware Installation Desktop Hardware Installation The switch can be mounted in an EIA standard-size, 19-inch rack, which can be placed in a wiring closet with other equipment. Attach the mounting brackets at the switch’s front panel (one on each side), and secure them with the provided screws. The site where you install the hub stack may greatly affect its performance.
TRENDnet User’s Guide Basic Installation 3. Assign a static IP address to your computer’s network adapter in the subnet of 192.168.10.x (e.g. 192.168.10.25) and a subnet mask of 255.255.255.0. TEG-30102WS 6. Click System, then click IPv4, click IP Address, and in the first entry, click Modify. 7. Configure the switch IP address settings to be within your network subnet, then click Apply.
TRENDnet User’s Guide TEG-30102WS Connect additional devices to your switch You can connect additional computers or other network devices to your switch using Ethernet cables to connect them to one of the available 2.5G Ports (1-8). Check the status of the LED indicators on the front panel of your switch to ensure the physical cable connection from your computer or device. Note: If you encounter issues connecting to your network, there may be a problem with your computer or device network settings.
TRENDnet User’s Guide Configure your switch TEG-30102WS Switch Info View your switch status information Access your switch management page Note: Your switch default management IP address http://192.168.10.200 is accessed through the use of your Internet web browser (e.g. Internet Explorer®, Firefox®, Chrome™, Safari®, Opera™) and will be referenced frequently in this User’s Guide. 1. Open your web browser and go to the IP address http://192.168.10.200.
TRENDnet User’s Guide TEG-30102WS Administration Information System Name – Displays the identifying system name of your switch. This information can be modified under the System section. System Location - Displays the identifying system location of your switch. This information can be modified under the System section. System Contact – Displays the identifying system contact or system administrator of your switch. This information can be modified under the System section.
TRENDnet User’s Guide TEG-30102WS System Set your system information System > System Management This section explains how to assign a name, location, and contact information for the switch. This information helps in identifying each specific switch among other switches in the same local area network. Entering this information is optional. 1. Log into your switch management page (see “Access your switch management page” on page 11). 4. Click Apply. 2. Click on System, and click on System Management. 3.
TRENDnet User’s Guide Set your IPv4 settings TEG-30102WS 4. Click Apply. System > IPv4 > IP Address This section allows you to change your switch IPv4 address settings. Typically, the IP address settings should be changed to match your existing network subnet in order to access the switch management page on your network. Default Switch IPv4 Address: 192.168.10.200 5. Click Save Settings to Flash (menu). Default Switch IPv4 Subnet Mask: 255.255.255.0 1.
TRENDnet User’s Guide TEG-30102WS Create and assign IPv4 address interfaces to VLANs 4. Select the ports to assign to this VLAN and click Apply. System > IPv4 > IP Address In this example, assign ports 3 and 4 as untagged members of VLAN 50. This section also allows you to create additional IP interfaces for different IP networks for IP routing and assign them to a specific VLAN interfaces. First, you must create a new VLAN under Bridge > VLAN > Tagged VLAN settings.
TRENDnet User’s Guide TEG-30102WS For new IPv4 address interface, enter the IP Address, and Subnet Mask to assign to the VLAN and click Apply. Adding IPv4 Static ARP entries In the example, we will assign an IPv4 address of 192.168.50.200 and subnet mas of 255.255.255.0. This section also allows you to create static ARP entries which may reduce some network overhead by creating entries for hosts that will consistently communicate to the switch in the current network environment.
TRENDnet User’s Guide TEG-30102WS Creating IPv4 Static Routes System > IPv4 > Route Settings The switch supports IPv4 static IP routing which can be used to route traffic between multiple IP subnets. 1. Log into your switch management page (see “Access your switch management page” on page 11). 2. Click on System, click IPv4, and click Route Settings. 3. Review the IPv4 Route Settings below. After you have entered all of the parameters for the static route, click Add to add to the IPv4 Route table.
TRENDnet User’s Guide TEG-30102WS Set your IPv6 settings System > IPv6 > IPv6 Address Use the IPv6 System Settings page to configure the IPv6 network interface, which is the logical interface used for in-band connectivity with the switch via all of the switch's front-panel ports. The configuration parameters associated with the switch's network interface do not affect the configuration of the front-panel ports through which traffic is switched or routed. 1.
TRENDnet User’s Guide TEG-30102WS Create and assign IPv6 address interfaces to VLANs 4. Select the ports to assign to this VLAN and click Apply. System > IPv6 > IPv6 Address In this example, assign ports 3 and 4 as untagged members of VLAN 50. This section also allows you to create additional IP interfaces for different IPv6 networks for IP routing and assign them to a specific VLAN interfaces. First, you must create a new VLAN under Bridge > VLAN > Tagged VLAN settings.
TRENDnet User’s Guide TEG-30102WS For new IPv6 address interface, set IPv6 State to Enabled, and enter the IPv6 Unicast Address / Prefix Length to assign to the VLAN and click Apply. Add IPv6 neighbors In this example, we will assign fc50::2/64 IPv6 address interface to VLAN 50. This settings allows you to manually define IPv6 supported neighboring devices on your network. System > IPv6 > Neighbor Settings 1. Log into your switch management page (see “Access your switch management page” on page 11).
TRENDnet User’s Guide 4. Click Save Settings to Flash (menu). TEG-30102WS 5. Click Save Settings to Flash (button), then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. 5. Click Save Settings to Flash (button), then click OK.
TRENDnet User’s Guide DNS Settings System > DNS Settings TEG-30102WS Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. This section allows you to connect to a specific DNS server with a specific IP address. 1. Log into your switch management page (see “Access your switch management page” on page 11). Restrict access to switch management page System > IP Access List 2.
TRENDnet User’s Guide TEG-30102WS 4. Click Save Settings to Flash (menu). In the Password field, enter the new password and enter the new password again the Confirm Password field to verify. Then, click Apply. Note: The password consists of up to 12 alphanumeric characters. 5. Click Save Settings to Flash (button), then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied.
TRENDnet User’s Guide TEG-30102WS SNMP Agent: Click the drop-down list to one of the following options. o Enabled - When you enable this parameter, the SNMP agent is active. You can manage the switch with SNMP network management software and the switch’s private MIB. o Disabled - When you enable this parameter, the SNMP agent is inactive. Telnet Agent: Click the drop-down list to one of the following options o Enabled – When you enable this parameter, the Telnet agent is active.
TRENDnet User’s Guide TEG-30102WS 4. Click Save Settings to Flash (menu). Clock Mode: Select Local Time to manually configure your date and time settings or select SNTP to configure your switch to automatically obtain settings from an network time server. 5. Click Save Settings to Flash (button), then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied.
TRENDnet User’s Guide TEG-30102WS 3. Review the settings. Click Apply to save changes. SSL Status: o Enabled – Enables HTTPS/SSL management access and disables HTTP unsecured mode. o Disabled – Disabled HTTPS/SSL management access and enabled HTTP unsecured mode. (Default setting). 4. Click Apply. 5. Click Save Settings to Flash (button), then click OK.
TRENDnet User’s Guide View and setup your switch logging System > System Log Settings The system log is designed to monitor the operation the switch by recording the event messages it generates during normal operation. These events may provide vital information about system activity that can help in the identification and solutions of system problems. 1. Log into your switch management page (see “Access your switch management page” on page 11). 2. Click on System, and click on System Log Settings.
TRENDnet User’s Guide TEG-30102WS Physical Interface o Configure your switch ports and view port status Physical Interface This section allows you to configure the physical port parameters such as speed, duplex, flow control, and jumbo frames. This section also reports the current link status of each port and negotiated speed/duplex. Additionally you will be able to set your BPDU ports for Spanning Tree Configuration and EAP ports for 802.1x port-based authentication configuration. Admin.
TRENDnet User’s Guide TEG-30102WS Note: When selecting a Mode setting, the following points apply: o When a twisted-pair port is set to Auto-Negotiation, the end node should also be set to Auto-Negotiation to prevent a duplex mode mismatch. o A switch port using Auto-Negotiation defaults to half-duplex if it detects that the end node is not using Auto-Negotiation. This can result in a mismatch if the end node is operating at a fixed duplex mode of full-duplex.
TRENDnet User’s Guide Spanning Tree (STP, RSTP, MSTP) Configure Spanning Tree Protocol settings Bridge > Spanning Tree > Protocol Settings Spanning Tree Protocol (STP) provides network topology for any arrangement of bridges/switches. STP also provides a single path between end stations on a network, eliminating loops. Loops occur when alternate routes exist between hosts.
TRENDnet User’s Guide TEG-30102WS Configure Spanning Tree Protocol port settings External Cost: This defines a metric that indicates the relative cost of forwarding packets to the specified port list. Port cost can be set automatically or as a metric value. Define a value between 1 and 200000000 to determine the external cost. The lower the number, the greater the probability the port will be chosen to forward packets. The default port cost: 100Mbps port = 200000. Gigabit port = 20000.
TRENDnet User’s Guide P2P: Choosing the Forcetrue parameter indicates a point-to-point (P2P) shared link. P2P ports are similar to edge ports however they are restricted in that a P2P port must operate in full-duplex. Like edge ports, P2P ports transition to a forwarding state rapidly thus benefiting from RSTP. A P2P value of Forcefalse indicates that the port cannot have P2P status. Auto allows the port to have P2P status whenever possible and operate as if the P2P status were true.
TRENDnet User’s Guide TEG-30102WS View your Spanning Tree Protocol Instance Information (MSTP) Bridge > Spanning Tree > Instance Information 1. Log into your switch management page (see “Access your switch management page” on page 11). 2. Click on Bridge, click on Spanning Tree, and click on Instance Information. 3. View your MSTP instance information. MST Table: Make changes to the table entry, and click Apply modify or click Delete to remove the ID entry.
TRENDnet User’s Guide TEG-30102WS Configure Spanning Tree Protocol MST Port Settings (MSTP) Trunk Config (Link Aggregation) Bridge > Spanning Tree > MST Settings Configure port trunk settings 1. Log into your switch management page (see “Access your switch management page” on page 11). Bridge > Trunk Config > Trunking 2. Click on Bridge, click on Spanning Tree, and click on MST Port Settings. 3. Review the settings. For each entry, click Apply to save changes.
TRENDnet User’s Guide Click the drop-down list and select one of the following options. TEG-30102WS View your trunk group status information Active - The specific aggregator will broadcast and respond to LACPDU (LACP Data Unit) packets. This setting enables the dynamic LACP feature for the trunk. Bridge > Trunk Config > LACP Group Status Passive - The specific aggregator will not broadcast LACPDU packets, but it will respond to them. This setting disables the LACP feature for the trunk 1.
TRENDnet User’s Guide TEG-30102WS Configure your port priority Mirroring Bridge > Trunk Config > Port Priority Configure port mirror settings 1. Log into your switch management page (see “Access your switch management page” on page 11). Bridge > Mirroring 2. Click on Bridge, click on Trunk Config, and click on Port Priority.
TRENDnet User’s Guide TEG-30102WS Loopback Detection Enable loopback detection Bridge > Loopback Detection The loopback detection feature allows the switch to detect and prevent disruption from loops that occur on uplink or downlink switches directly connected to your switch. 1. Log into your switch management page (see “Access your switch management page” on page 11). 2. Click on Bridge and click on Loopback Detection. 4. Click Save Settings to Flash (menu). 3. Review the settings.
TRENDnet User’s Guide In the Loopback Detection table, select one of the Loopback Detection State choices from the drop down menu: Ignore: This parameter indicates that the setting in the All row do not apply to the Loopback Detection State field. In other words, each port is set individually. TEG-30102WS Static Unicast Add static unicast entries to the switch Bridge > Static Unicast In this section, you can add static unicast entries to the switch configuration.
TRENDnet User’s Guide In the list, you can click Modify to modify an entry or click Delete or delete the entry. You can also click Delete All to delete all the entries in the list. If the entries span multiple pages, you can navigate page number in the Page field and click Go or you can click First, Previous, Next, and Last Page to navigate the pages.
TRENDnet User’s Guide In the list, you can click Modify to modify an entry or click Delete or delete the entry. If the entries span multiple pages, you can navigate page number in the Page field and click Go or you can click First, Previous, Next, and Last Page to navigate the pages. TEG-30102WS IGMP Snooping Configure IGMP Snooping Settings Bridge > IGMP Snooping > Basic Settings 1. Log into your switch management page (see “Access your switch management page” on page 11). 2.
TRENDnet User’s Guide TEG-30102WS Configure IGMP Snooping Port Settings 6. Click Save Settings to Flash (button), then click OK. Bridge > IGMP Snooping > Port Settings Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. 1. Log into your switch management page (see “Access your switch management page” on page 11). 2. Click on Bridge, click on IGMP Snooping, and click on Port Settings. 3.
TRENDnet User’s Guide TEG-30102WS Configure IGMP Snooping Port Settings Bridge > IGMP Snooping > Port Settings 1. Log into your switch management page (see “Access your switch management page” on page 11). 2. Click on Bridge, IGMP Snooping, and Port Settings. 3. Review the settings. Click Apply to save the settings. 4. Click Save Settings to Flash (menu). Static Router Port – Select Enable for this option to assign a port as a static router port for IGMP snooping.
TRENDnet User’s Guide Configure IGMP Snooping Address Entry Bridge > IGMP Snooping > Address Entry 1. Log into your switch management page (see “Access your switch management page” on page 11). 2. Click on Bridge, click on IGMP Snooping, and click on Address Entry. 3. Review the settings. Address Entry Name: Enter the entry ID.
TRENDnet User’s Guide TEG-30102WS 4. Click Apply. 5. Click Save Settings to Flash (menu). 5. Click Save Settings to Flash (menu). 6. Click Save Settings to Flash (button), then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. MLD Snooping Configure MLD Snooping Settings Bridge > MLD Snooping > Basic Settings 1.
TRENDnet User’s Guide Max Response Time – Enter the maximum response time in seconds that client can wait before responding to a query. Robustness Variable – Enter the robustness value used to determine the number of times to send a message. TEG-30102WS 3. Review the settings. Click Apply to save the settings. Static Router Port – Select Enable for this option to assign a port as a static router port for IGMP snooping.
TRENDnet User’s Guide Configure MLD Snooping Address Entry Bridge > MLD Snooping > Address Entry 1. Log into your switch management page (see “Access your switch management page” on page 11). 2. Click on Bridge, click on MLD Snooping, and click on Address Entry. 3. Review the settings. Address Entry Name: Enter the entry ID.
TRENDnet User’s Guide TEG-30102WS Threshold – Enter the pps (packets per second) threshold. Note: Modifying settings in the row marked All, will apply the settings to all ports. 5. Click Save Settings to Flash (menu). 6. Click Save Settings to Flash (button), then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. 4. Click Save Settings to Flash (menu). 5.
TRENDnet User’s Guide 4. Click Save Settings to Flash (menu). TEG-30102WS 4. Click Save Settings to Flash (menu). 5. Click Save Settings to Flash (button), then click OK. 5. Click Save Settings to Flash (button), then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied.
TRENDnet User’s Guide TEG-30102WS VLAN Name – Enter the VLAN name. Management VLAN – Click the drop-down list and select Enabled to allow access to the switch management page through the new VLAN. If you want to restrict management access through this VLAN, select Disabled. Untagged VLAN ports are used to connect edge devices (VLAN unaware) such as computers, laptops, and printers to a specified VLAN.
TRENDnet User’s Guide TEG-30102WS Configure VLAN Port Settings Bridge > VLAN > Port Settings 5. Click Save Settings to Flash (button), then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. In this section, you can modify the port VID settings, acceptable frame types, and ingress filtering. 1.
TRENDnet User’s Guide TEG-30102WS View the switch VLAN dynamic forwarding table Create a private VLAN Bridge > VLAN > Dynamic Forwarding Table Bridge > VLAN > Private VLAN This section allows you to view the VLAN forwarding table with dynamically generated forwarding table entries as devices more devices are connected to your switch. The private VLAN feature allows you to create a more secure VLAN that is completely isolated to its members and cannot communicate with other VLANs.
TRENDnet User’s Guide TEG-30102WS Click on the Forwarding Ports ratio button that applies to your configuration. View the current VLAN database Click Apply. Bridge > VLAN > VLAN Current Database 1. Log into your switch management page (see “Access your switch management page” on page 11). 2. Click on Bridge, click on VLAN, and click on Private VLAN. 3. View the current VLAN database in the table.
TRENDnet User’s Guide TEG-30102WS 3. Select Enable or Disable from the drop down menu under Asymmetric VLAN. 4. Click Apply. 5. Click Save Settings to Flash (menu). 6. Click Save Settings to Flash (button), then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. © Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEG-30102WS QoS (Quality of Service) When a port on an Ethernet switch becomes oversubscribed, its egress queues contain more packets than the port can handle in a timely manner. In this situation, the port may be forced to delay the transmission of some packets, resulting in the delay of packets reaching their destinations.
TRENDnet User’s Guide TEG-30102WS Set Port Priority Set DSCP (Differentiated Services Code Point) Class Mapping settings Bridge > QoS > Port Priority Bridge > QoS > DSCP The Port Priority values are assigned to an untagged frame at ingress for internal processing in the switch. This procedure explains how to change the default mappings of port priorities to the User Priority. This is set at the switch level. You cannot set this at the per-port level.
TRENDnet User’s Guide TEG-30102WS Set the Scheduling Algorithm Bridge > QoS > Scheduling Algorithm 1. Log into your switch management page (see “Access your switch management page” on page 11). 2. Click on Bridge, click on QoS and click on Scheduling Algorithm. 3. Review the settings. Click Apply to save the settings. Strict Priority - The port transmits all packets out of higher priority queues before transmitting any from the lower priority queues.
TRENDnet User’s Guide TEG-30102WS SNMP Configure the SNMP View Table You can manage a switch by viewing and configuring the management information base (MIB) objects on the device with the Simple Network Management Program (SNMP). This chapter describes how to configure SNMP. A Group Name, IP address of the switch and at least one community string is the minimum required to manage the switch using SNMP. SNMP > View Table Set the SNMP Engine ID 1.
TRENDnet User’s Guide TEG-30102WS Modifying SNMP View Table Entries Configure the SNMP Group Access Table If you need to modify an entry in the View Table page, you must first delete the entry and then re-enter it. SNMP > Group Access Table The SNMP View Names are defined in the SNMP Group Access table and are based on the User and Group Names Deleting SNMP View Table Entries In the Action column of the table, click Delete for the View table entry that you want to remove. 1.
TRENDnet User’s Guide TEG-30102WS Configure the SNMP User/Group Table SNMP > SNMP User/Group An SNMP User Name and Group Name definition is the basis for all the other SNMP tables. You can create and delete View Names by following the procedures in the following sections: 1. Log into your switch management page (see “Access your switch management page” on page 11). 2. Click on SNMP and click on SNMP User/Group. Modifying SNMP View Names 3. Review the settings.
TRENDnet User’s Guide Click Add. The new User Name and Group Name are displayed on the SNMP User/Group page. TEG-30102WS Configure the SNMP Community Table SNMP > Community Table A community string has attributes for controlling who can use the string and what the string will allow a network management station to do on the switch. The Web Management Utility does not provide any default community strings.
TRENDnet User’s Guide Delete SNMP Community Settings To delete a Community Name, click Delete next to the entry in the table that you want to remove. The deleted Community Name is no longer displayed in the Community table. No confirmation message is displayed. TEG-30102WS Configure the SNMP Trap Management SNMP > Trap Management A Host IP address is used to specify a management device that needs to receive SNMP traps sent by the switch.
TRENDnet User’s Guide TEG-30102WS Access Control Config Access Control configuration allows you to control different aspects of the Ethernet traffic as it enters the switch ports and is process through the Switch. You can specify what traffic is permitted or denied to flow through the switch by setting up specific filter criteria at an ingress port. You can also manage the switching priority of Ethernet packets. All of this is done by specifying policies that define the filtering and priority behavior.
TRENDnet User’s Guide TEG-30102WS Add ETYPE o To add an ETYPE policy, use the following procedure: Click Add ETYPE, The Policy Settings page. Enter a number in the Policy Index field. The Policy Index is a unique number within the range of 1 – 256 which identifies the policy. This field is mandatory. Enter a number in the VLAN ID field. A unique number identifying a VLAN ranging from 1 to 4094. Enter a number in the 802.1q Priority field.
TRENDnet User’s Guide TEG-30102WS Add ARP o Target IP Address - Specifies the IP address of the sender To add an ARP policy, use the following procedure: o Mask Length – Indicates the length of the Sender IP Address ranging from 1 – 32 o Policy Action – Indicates if the policy will be Permitted or Denied. o Policy Action: In the Permit/Deny field, use the pull down menu to select one of the following parameters: Click Add ARP, The Policy Settings page.
TRENDnet User’s Guide TEG-30102WS Enter a number in the VLAN ID field. A unique number identifying a VLAN ranging from 1 to 4094. Enter a number in the 802.1q Priority field. Enter the priority level of the frame ranging from 0 – 7. Deny - This selection drops ingress packets that conform to the specified Replaced-CoS or Replaced-DSCP. Choose the parameters to add for the policy, and enter data one or more of the parameters required for your policy.
TRENDnet User’s Guide Enter a number in the 802.1q Priority field. Enter the priority level of the frame ranging from 0 – 7. Choose the parameters to add for the policy, and enter data one or more of the parameters required for your policy.
TRENDnet User’s Guide TEG-30102WS 5. Click Save Settings to Flash (button), then click OK. 5. Click Save Settings to Flash (button), then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied.
TRENDnet User’s Guide 3. Click the RMON Status drop-down list and select Enabled to enable RMON. Click Apply to save settings. TEG-30102WS Owner: This parameter is used to identify the person who created an entry. It is primarily intended for switches that are managed by more than one person, and is an optional field. Click Add to add the entry to the table. 4. Click Save Settings to Flash (menu). 5. Click Save Settings to Flash (button), then click OK.
TRENDnet User’s Guide Configure parameters for RMON history control settings TEG-30102WS Click Add to add the entry to the table. RMON > History RMON histories are snapshots of port statistics. They are taken by the switch at predefined intervals and can be used to identify trends or patterns in the numbers or types of ingress packets on the ports on the switch. The snapshots can be viewed with your SNMP NMS software with the history group of the RMON portion of the MIB tree.
TRENDnet User’s Guide Configure parameters for RMON alarms RMON > Alarms RMON alarms are used to generate alert messages when packet activity on designated ports rises above or falls below specified threshold values. The alert messages can take the form of messages that are entered in the event log on the switch or traps that are sent to your SNMP NMS software or both. RMON alarms consist of two thresholds. There is a rising threshold and a falling threshold.
TRENDnet User’s Guide Click Add to add the entry to the table. TEG-30102WS Configure parameters for RMON events RMON > Event An event specifies the action of the switch when the ingress packet activity on a port crosses a statistical threshold defined in an alarm. The choices are to log a message in the event log of the switch, send an SNMP trap to an SNMP workstation, or both.
TRENDnet User’s Guide Click Add to add the entry to the table. TEG-30102WS Voice VLAN This chapter contains a description of the Switch’s Voice VLAN feature and the procedures to create, modify, and delete a voice VLAN configuration. The Voice VLAN feature is specifically designed to maintain high quality, uninterrupted voice traffic through the switch. When talking on a voice over IP phone, a user expects to have no interruptions in the conversation and excellent voice quality.
TRENDnet User’s Guide However, it is possible that you can find more than one OUI from the same manufacturer among the IP phones you are installing. It is also possible that your IP phones are from two or more different manufacturers in which case you will find different OUIs for each manufacturer. If you identify more than one OUI among the IP phones being installed, then one MAC address representing each individual OUI must be configured in the voice VLAN. You can enter a total of 10 OUIs.
TRENDnet User’s Guide TEG-30102WS port will be removed from the voice VLAN. The range is 1 to 120 hours. o CoS - This parameter is CoS priority level assigned to the voice data packets received on each voice VLAN port. For the COS priority to be effective, QoS must be Enabled. Click Apply to save the settings. 4. Click Save Settings to Flash (menu). 5. Click Save Settings to Flash (button), then click OK.
TRENDnet User’s Guide Enter the MAC address in the User Defined OUI - Telephony OUI field of one of the IP phones with the manufacturer's OUI. Click Add. The new OUI entry is displayed in the table at the bottom of the page. Note: If you find more than one OUI among the IP phones you are installing, enter one MAC address that represents each individual OUI. You can enter a total of 16 OUIs.
TRENDnet User’s Guide TEG-30102WS 3. Review the settings. Click Apply to save the settings. Configure the following parameters as required: Port Access Control – Select Enabled to enable port access control or Disabled to disable it. Disabled is selected by default. Authentication Method - This parameter indicates the authentication method used by the switch. Select one of the following choices: o RADIUS: This parameter configures port security for remote authentication.
TRENDnet User’s Guide TEG-30102WS 4. To review your configured settings click on the Configuration Status 4. Click Save Settings to Flash (menu). 5. Click Save Settings to Flash (button), then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. © Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Create Dial-In Users (Local Authentication Method) Security > Dial-in User Dial-in User feature provides the local authentication server for port security when a remote (RADIUS) server is not available. TEG-30102WS In the list, you can click Modify to modify an entry or click Delete or delete the entry. You can also click Delete All to delete all of the entries in the table.
TRENDnet User’s Guide Add RADIUS Servers (RADIUS Authentication Method) TEG-30102WS In the list, you can click Modify to modify an entry or click Delete or delete the entry. Security > RADIUS 1. Log into your switch management page (see “Access your switch management page” on page 11). 2. Click on Security and click on RADIUS. 4. Click Save Settings to Flash (menu). 3. Review the settings. Server Priority – Enter the RADIUS Server priority (Highest: 1, Lowest: 5).
TRENDnet User’s Guide TEG-30102WS Add TACACS+ Servers (TACACS+ Authentication Method) Security > TACACS+ Terminal Access Controller Access Control System (TACACS+) provides centralized security user access validation. The system supports up-to 5 TACACS+ servers. TACACS+ provides a centralized user management system, while still retaining consistency with RADIUS and other authentication processes.
TRENDnet User’s Guide Destination MAC Filter TEG-30102WS 4. The MAC address will be added to the table. Security > Destination MAC Filter This section contains an explanation of the Destination MAC Filter feature as well a procedure for configuring it. This section includes the following information: The Destination MAC Filter feature prevents the switch from forwarding packets to a specified device.
TRENDnet User’s Guide Denial of Service (DoS) Security > Denial of Service The switch has built-in DoS prevention features to restrict specific type of traffic associated denial of service attacks on your network. By default, all of the DoS settings are set to Allow, which allow any type of traffic to pass through the switch. Setting one of the items to Deny will set the switch to check for traffic matching the selected item and deny any traffic matching the rule.
TRENDnet User’s Guide TEG-30102WS ARP Inspection Click on Security, ARP Inspection, and click on Port Settings. Security > ARP Inspection Review the settings below and click Apply when configuration is completed. This section allows you to create ARP inspection policies for security purposes. The ARP inspection can be set to permit or deny the host based VLAN & port assignment.
TRENDnet User’s Guide Port Security Control Security > Port Security Control The port security feature allows you to add additional security to your switch by limited the number of MAC addresses learned by each port. 1. Log into your switch management page (see “Access your switch management page” on page 11). TEG-30102WS Violation Action - The resulting action when the maximum allowed violations is reached per port.
TRENDnet User’s Guide TEG-30102WS DHCP Snooping Here is a summary of the rules to observe when you configure DHCP Snooping: A trusted port is connected to one of the following: o Directly to the legitimate trusted DHCP Server. 5. Click Save Settings to Flash (button), then click OK. o A network device relaying DHCP messages to and from a trusted server.
TRENDnet User’s Guide Enable DHCP Snooping TEG-30102WS 2. Click on DHCP Snooping and click on Trusted Interfaces. DHCP Snooping > VLAN Settings In this section, you can enable DHCP Snooping. 1. Log into your switch management page (see “Access your switch management page” on page 11). 3. Below each port, click the Check each port to enable the port as being trusted with the DHCP Snooping feature. To define a port as untrusted for DHCP Snooping, uncheck the box.
TRENDnet User’s Guide TEG-30102WS DHCP Server DHCP VLAN Settings A DHCP (Dynamic Host Configuration) Server is a network server that automatically provides and assigns IP addresses, default gateways and other network parameters to client devices. This relies on DHCP to respond to broadcast queries by clients. DHCP server automatically sends the required network parameters for clients to properly communicate on a network. DHCP > DHCP Server > VLAN Settings 1.
TRENDnet User’s Guide TEG-30102WS End IP Address: Enter the ending IP address to be excluded from the DHCP server range. In the list, you can View an entry or click Delete or delete the entry. You can also click Delete All to delete all of the entries in the table. If the entries span multiple pages, you can navigate page number in the Page field and click Go or you can click First, Previous, Next, and Last Page to navigate the pages. 4. Click Save Settings to Flash (menu). 5.
TRENDnet User’s Guide TEG-30102WS DHCP Pool DHCP > DHCP Server > Pool 4. Click Save Settings to Flash (menu). 1. Log into your switch management page (see “Access your switch management page” on page 11). 5. Click Save Settings to Flash (button), then click OK. 2. Click on DHCP, then click on DHCP Server, and click on Pool. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. 3.
TRENDnet User’s Guide o Replace – Replaces the packet when an Option 82 packet is passed through the switch o Keep – Keeps the Option 82 packet when it passed through the switch o Drop – Drops the Option 82 packet when it is passed through the switch 4. Click Save Settings to Flash (menu). TEG-30102WS 3. Review the settings. Enabling or Disabling LLDP From the LLDP parameter, select one of the following radio button choices and click Apply to save the settings.
TRENDnet User’s Guide TEG-30102WS Set LLDP Port State For each port, click the State drop-down list and choose from the following options. Disabled: Indicates LLDP is disabled on the port. The port cannot receive or transmit LLDP data packets. Enabled: Indicates LLDP is enabled on the port. The port can receive and transmit LLDP data packets. RxOnly: Indicates LLDP is enabled on the port. The port can receive LLDP data packets. TxOnly: Indicates LLDP is enabled on the port.
TRENDnet User’s Guide TEG-30102WS View LLDP Neighbor Information Statistic LLDP > LLDP Neighbor Information 1. Log into your switch management page (see “Access your switch management page” on page 11). Statistics provide important information for troubleshooting switch problems at the port level. The Web Management Utility provides a two statistics charts, including Traffic Information and Error Information. 2. Click on LLDP and click on LLDP Neighbor Information.
TRENDnet User’s Guide TEG-30102WS View Error Information Statistics Statistic > Error Information 1. Log into your switch management page (see “Access your switch management page” on page 11). 2. Click on Statistic and click on Traffic Information. 3. View the Error Information Statistics. InErrors: Inbound Errors (Pkts), number of inbound errors in packets per second. OutErrors: Outbound Errors (Pkts), number of outbound error packets. DropEvents: Drop Events, number of packets dropped.
TRENDnet User’s Guide Switch Maintenance Upgrade your switch firmware TEG-30102WS Firmware Upgrade via HTTP Settings 1. Log into your switch management page (see “Access your switch management page” on page 11). Tools > Firmware Upgrade TRENDnet may periodically release firmware upgrades that may add features or fix problems associated with your TRENDnet switch model and version.
TRENDnet User’s Guide Firmware Upgrade via TFTP Settings Note: Before using this method, you will require a TFTP server. There are third party TFTP server applications available for this function. If you are not familiar with the TFTP protocol, it is recommended to use the HTTP method. 1. Log into your switch management page (see “Access your switch management page” on page 11).
TRENDnet User’s Guide TEG-30102WS Backup/Restore via TFTP Settings Note: Before using this method, you will require a TFTP server. There are third party TFTP server applications available for this function. If you are not familiar with the TFTP protocol, it is recommended to use the HTTP method. To restore your switch configuration: 1. Log into your switch management page (see “Access your switch management page” on page 11). To backup your switch configuration: 2.
TRENDnet User’s Guide Cable Diagnostics Test TEG-30102WS The results will be displayed in the Cable Diagnostic Table below. Tools > Cable Diagnostics The switch provides a basic cable diagnostic tool in the GUI for verifying the pairs in copper cabling and estimated distance for troubleshooting purposes. Note: 1. If the cable length displays N/A, it means that the cable length is Not Available. The may be due to the port being unable to determine the estimated cable length.
TRENDnet User’s Guide TEG-30102WS Reboot/Reset to factory defaults To reset your switch to factory defaults: Tools > Reboot You may want to reset your router to factory defaults if you are encountering difficulties with your router and have attempted all other troubleshooting. Before you reset your router to defaults, if possible, you should backup your router configuration first, see “Backup and restore your router configuration settings” on page 44.
TRENDnet User’s Guide Network Connectivity Test (Ping Tool) Tools > Ping This chapter provides the procedure to ping a node on your network from the switch. This procedure is useful in determining whether an active link exists between the switch and another network device. The device you are pinging must be a member of the Default VLAN and within the same local area network as your switch.
TRENDnet User’s Guide Specifications Bridge MIB IEEE8021-Q Technical Specifications RMON (Group 1,2,3,9) RFC 2819 Hardware Standards Interface group MIB using SMIv2 RFC 2863 IEEE 802.1d, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1X, IEEE 802.1ab, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.
TRENDnet User’s Guide Multicast Port Mirror IGMP snooping v1, v2, v3 IP protocol 1-255 IGMP fast leave TCP/UDP port 1-65535 Static multicast entries 802.1p MLD Snooping v1, v2 DSCP Up to 1K multicast groups IPv4/IPv6 address Up to 256 entries One to one Many to one Storm Control Specifications Layer 3 Features IP interfaces: Up to 8 Broadcast (Min. limit: 10pps) Routing table entries: Up to 32 (IPv4 / IPv6) Multicast (Min.
TRENDnet User’s Guide Troubleshooting Q: I typed http://192.168.10.200 in my Internet Browser Address Bar, but an error message says “The page cannot be displayed.” How can I access the switch management page? Answer: 1. Check your hardware settings again. See “Switch Installation” on page 8. 2. Make sure the Power and port Link/Activity and WLAN lights are lit. 3. Make sure your network adapter TCP/IP settings are set to Use the following IP address or Static IP(see the steps below). 4.
TRENDnet User’s Guide Appendix Appendix Note: If you are experiencing difficulties, please contact your computer or operating system manufacturer for assistance.
TRENDnet User’s Guide Appendix In MAC OS 10.4, from the Show drop-down list, select Built-in Ethernet and select the TCP/IP tab. In MAC OS 10.5/10.6, in the left column, select Ethernet. e. Configure TCP/IP to use a static IP. In MAC 10.4, from the Configure IPv4, drop-down list, select Manually and assign your network adapter a static IP address. Then click the Apply Now button. In MAC 10.5/10.6, from the Configure drop-down list, select Manually and assign your network adapter a static IP address.
TRENDnet User’s Guide Appendix Federal Communication Commission Interference Statement RoHS This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
TRENDnet User’s Guide Limited Warranty TRENDnet warrants only to the original purchaser of this product from a TRENDnet Limited Warranty In the event that, after evaluation, TRENDnet cannot replace the defective product or there is no comparable model available, we will refund the depreciated value of the product. authorized reseller or distributor that this product will be free from defects in material and workmanship under normal use and service.
TRENDnet User’s Guide Limited Warranty shipping from outside of the USA and Canada are responsible for any return shipping CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, and/or customs charges, including but not limited to, duty, tax, and other fees.
