Quick Installation Guide TE100-PCIFC 1.
Table of Table ofContents Contents Español ..................................................................................................... 1 1. Antes de iniciar .................................................................................. 1 2. Cómo se instala ................................................................................ 2 Troubleshooting ......................................................................................... 5 Version 06.11.
1. Antes de iniciar Contenidos del paquete TE100-PCIFC ? ? CD-ROM del controlador Guía de instalación rápida ? multilingüe Requisitos del sistema Ranura PCI 2.2 de 32 bits ? ? Unidad de CD-ROM ? CPU: 300 MHz o superior/ 800 MHz o superior (Windows Vista) ? Memoria: 256MB de RAM o más/ 512MB de RAM o más (Windows Vista) ? Windows 98SE/ME/2000/2003 Server(32/64-bit) / XP(32/64-bit) / Vista (32/64-bit) ? Un cable de fibra multimodo de 62.
2. Cómo se instala Nota: 1. Para la instalación del controlador de Windows 98SE y ME, consulte la guía del usuario en el CD-ROM del controlador 2. No conecte el TE100-PCIFC a su PC a menos que se le indique. 1. Inserte el CD-ROM del controlador en su unidad de CD-ROM. 2. Haga clic en Run Autorun.exe (sólo para Windows Vista). 3. Haga clic en Install Driver (Instalar controlador) y luego haga clic en su sistema operativo.
4. Haga clic en OK. 5. Apaque su PC y luego abra la caja de su PC. 6. Introduzca la tarjeta PCIe de manera firme en la ranura para tarjeta PCIe disponible, después ENCIENDA el PC y espere hasta que aparezca el escritorio de Windows. 7. Los controladores se instalarán automáticamente.
Cómo conectar el TE100-PCIFC a su red 1. Conecte un cable multimodo tipo SC del TE100-PCIFC al convertidor de fibra a 10/100Mbps (Ej. TFC-110MSC) Nota: Compruebe que los cables TX y RX están invertidos en la conexión opuesta. 2. Conecte un cable Ethernet del convertidor de fibra a un puerto Gigabit Ethernet en su conmutador (Ej. TEG-424WS).
Troubleshooting Q1: I inserted the Driver CD-ROM into my computer's CD-ROM drive and the installation menu does not appear automatically. What should I do? A1: For Windows 2000/XP/2003 Server, if the installation menu does not appear automatically, click Start, click Run, and type D:\autorun where "D" in "D:\autorun.exe" is the letter assigned to your CD-ROM Drive, and then press the ENTER key on your keyboard.
Windows XP/2000 1. Go into the Control Panel, double-click the Network Connections icon and then rightclick the Local Area Connection icon and then click Properties. 2. Click Internet Protocol (TCP/IP) and then click Properties. Then click on Obtain an IP address automatically. Q4: I am not getting a network connection when I connect the TE100-PCIFC to my network. What should I do? A4: First, check the fiber cable. Make sure you are using 62.5/125µm multi-mode fiber cable.
Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local Authority or Retailer for recycling advice.
Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.trendnet.com/register 20675 Manhattan Place Torrance, CA 90501 USA Copyright ©2009. All Rights Reserved. TRENDnet.
