TRENDnet User’s Guide Cover Page
TRENDnet User’s Guide Contents Product Overview ................................................................................. 1 Package Contents .......................................................................................................... 1 Features ......................................................................................................................... 1 Product Hardware Features...........................................................................................
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Features Product Overview TV-IP851WC The Wireless PTZ Internet Camera, model TV-IP851W, provides wide visibility with its varied Pan and Tilt feature. Pan the camera side-to-side, a remarkable 340 degrees, and tilt up-and-down 115 degrees to broaden your viewing capabilities. Wireless n technology provides unsurpassed wireless coverage and improved streaming video quality.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Product Hardware Features Front Panel View Microphone Rear Panel View Light Sensor IR LED Rear Air Vents Camera Lens Focus Ring Antenna WPS button LAN port Power port Reset button LAN Port – Connect Ethernet cables to your wired network devices. Power Port – Connect the included power adapter from your camera to an available power outlet. Note: Use only the adapter that came with your camera.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Installation Wired Connection 1. Connect the Ethernet Cable If you intend to use the network camera as a wired device, connect one end of the included Ethernet cable into the Ethernet port on the rear panel of the camera and connect the other end to an available port on your network. If you prefer to use the camera on a wireless network, see below for instructions on connecting the power adapter. 2.
TRENDnet User’s Guide TV-IP851WC / TV-IP851WIC Wall mount installation To attach the metal plates carry out the following: Remove the two rubber pads under the base of the Camera. Slide the metal plate onto the base of the camera, making sure that the two holes on the base of the camera align with the two screw holes on the base of the camera. Secure the metal plate to the base of the Camera with the two screws provided. The camera can now be mounted to the ceiling or a wall.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Starting the TRENDnet Cloud Service Image B (wired connection) Note: (Connect the camera to the Internet and make sure its accessible to the web). 1. 2. Look underneath the camera for a similar URL (http://11223344.cam.trendnetcloud.com) on the label. Connect the power cable to the camera. 3. There are two methods to connect to the Internet, wired and wireless. For wireless, follow the instructions from Image A below.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Red Mode The Red Mode indicates the camera is connecting to the Internet or local network through a firewall. This mode doesn’t offer configuration and management options – just live streaming for 60 seconds. The firewall settings limits live streaming for each user. The “red” notification at the bottom of the viewing area warns users of the limited time. Refresh this screen continuously if you wish to view your camera’s live stream.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Using the AutoRun Wizard French Insert the included CD-ROM into your CD/DVD drive. The Install Wizard program will run automatically. Note: If the Install Wizard does not run, you may have autorun disabled on your machine. In this case, browse to the CD drive and run InstallWizard.exe to begin the installation wizard. Begin by selecting a language from the drop-down list. There is a choice of five languages – English, French, German, Russian, and Spanish.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Spanish 1. This is TRENDnet’s Terms of Use. Click Agree to continue. 2. The next step references information on the camera itself. Go to your camera and check the details at the bottom of the device. Click Next to continue, Back to go to the previous screen or Home to return to the Main Menu. Also enclosed, is a sticker with the same details attached. 3. The most important part of the setup process is the network connection type.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide button and click Next to continue, Back to go to the previous screen or Home to return to the Main Menu. 5. 6. 7. The wizard searches the network for your camera. 8. If you only have one camera on your network, the wizard will automatically select it (as shown below). Otherwise, if you have more than one camera, it provides several options from the list. The wizard provides the Model Name and MAC Address of the camera.
TRENDnet User’s Guide 9. Password Settings. Follow the instructions on the screen. Remember to change the password with an 8 bit preset. The default username and password is admin. Tick the Change Password checkbox to enter the new password details. The password should be between 8 and 16 characters. Click Next to continue, Back to go to the previous screen or Home to return to the Main Menu. TV-IP851WC / TV-IP851WIC 11. The initial setup is complete.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Wireless Connection Using WPS 12. The mobile option allows the user to download the TRENDnet Cloud App in either Apple or Google android format. To use this feature, the user must have a Barcode Scanner App on their mobile device. This is also available from the Apple App Store or Google’s Play. You are now ready to use your camera. Click Finish to exit.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide 2. 3. Follow the instructions and click Next to continue. If you wish to go to the previous screen, click Back or Home to return to the main menu. 4. If you only have one camera on your network, the wizard will automatically select it (as shown below). Otherwise, if you have more than one camera, it provides several options from the list. The wizard provides the Model Name and MAC Address of the camera.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide 5. Password Settings. Follow the instructions on the screen. Remember to change the password with an 8 bit preset. The default username and password is admin. Tick the Change Password checkbox to enter the new password details. The password should be between 8 and 16 characters. Click Next to continue, Back to go to the previous screen or Home to return to the Main Menu. connection is inactive or the Cloud server cannot be found.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide You are now ready to use your camera. Click Finish to exit. 2. Connect one end of the network cable to your camera and the other end to your router. Click Next to continue, Back to go to the previous screen or Home to return to the Main Menu. 3. The wizard searches the network for your camera. Connecting Wireless Network Manually 1. Follow the instructions in the next screen to Power up the Camera.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide admin. Tick the Change Password checkbox to enter the new password details. The password should be between 8 and 16 characters. Click Next to continue, Back to go to the previous screen or Home to return to the Main Menu. 4. 5. If you only have one camera on your network, the wizard will automatically select it (as shown below). Otherwise, if you have more than one camera, it provides several options from the list.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide 9. 8. The wizard searches for wireless Access Points. Click the Rescan button at any time if you want to find your AP. Once it finds the wireless AP you are looking for, select it and enter the wireless network password of the AP. Click Next to continye Next, you are prompted to disconnect your network cable from the camera/router. Click Next to continue, Back to go to the previous screen or Home to return to the Main Menu. 10.
TRENDnet User’s Guide TV-IP851WC / TV-IP851WIC 11. The initial setup is complete. The main feature is the Cloud Access accessibility feature. Click the link(s) or icon below to create a shortcut on your desktop. Also, below the icon is a warning message. This warning message is only shown when the internet connection is inactive or the cloud server cannot be found. Make sure the internet connection is active, click Retry. When the Cloud server isn’t found, the server may be busy or under maintenance.
TRENDnet User’s Guide TV-IP851WC / TV-IP851WIC Mobile Apps Using your mobile device, in this example it is an Android phone, touch the Bar Code scanning app on your phone. Hold it up to the QR Code on the wizard that reads, Android, and snap to scan the image. The Bar Code app will read the QR Code and record it. The app copies the QR link and provides a HTML link to the TRENDnet app. Click on the link. Download the app, install it and use the app on your mobile device to view the TRENDnet camera.
TRENDnet User’s Guide TV-IP851WC / TV-IP851WIC Here is Apple iTunes version Scan the QR Code using one of IOS’s QR Code apps. The app automatically creates an HTML link to the iTunes App Store. Link the link. You are immediately directed to the iTunes App Store. Click the link to download. © Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TV-IP851WC / TV-IP851WIC Configuration After completing the AutoRun Wizard, you are ready to use your camera. The camera’s built-in Web configuration utility is designed to allow you to easily access and configure your TV-IP851WC or TV-IP851WIC camera. Open a web browser such as Internet Explorer® and enter the IP address of your camera (Default IP Address: http://192.168.10.30). To log in, use the User name admin and the password you created in the Setup Wizard.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide The Congratulations page appears. Click Login to go to the Login page again. To log in, enter the Username admin and the newly created password. This page only appears at the first time log in. Viewing Video Click VIEW VIDEO | ACTIVEX or VIEW VIDEO | JAVA to begin viewing live video from your camera. VIEW VIDEO | ACTIVEX Before enabling this feature make sure your system is upgraded with the latest Active X plug-in updates.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide VIEW VIDEO | JAVA Viewing Camera Settings Please make sure that you have the latest version of Java installed on your machine to ensure proper operation when viewing video in Java mode. The Java application can be downloaded from Sun’s website free of charge (http://www.java.com) To view camera settings: 1. 2. Login to the camera Click ADMINISTRATION. The system status screen appears.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide System This screen shows the Camera Name, Location, Model, Firmware Version, MAC Address, IP Address, Ethernet Link Status, Speed and Duplex type. Audio This screen shows whether audio is enabled and the volume level of the audio. Wireless Video This screen shows the details of the video capture settings including Video Resolution, Compression Rate, Frame Rate, Frame Size and Light Frequency.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Network Active Users This screen shows various network statistics related to your camera including IP Address, Subnet Mask and Default Gateway. This screen shows whether there are any active users logged on to the camera viewing live video. Cloud Link This screen shows the Cloud server URL and its status. © Copyright 2013 TRENDnet. All Rights Reserved.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Configuring Camera Settings The TV-IP851WC/TV-IP851WIC allows you to make configuration changes from anywhere by connecting to the camera using a standard web browser. To configure camera settings: 1. 2. 3. Login to the camera as described in the section Using the web-based configuration interface. Click ADMINISTRATION. The system status screen appears. Click CONFIGURATION from the menu on the left side of the screen.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Frame Rate (Frames/Sec.): Select the number of frames per second you would like for your video. Higher rates provide smoother video but require more bandwidth on your network or Internet connection. Brightness Control: Allows you to control the brightness level. Enter a value between 1 and 128. Contrast Control: Allows you to control the contrast level. Enter a value between 1 and 128.
TRENDnet User’s Guide TV-IP851WC / TV-IP851WIC Wireless Connection Mode: Infrastructure is a wireless connection using an access point as a transmission point of all wireless devices. Ad-Hoc is a wireless connection used without an access point, where your TV-IP851WC or TV-IP851WIC is directly connected to your PC. This is done using the on-board wireless adapter on the TV-IP851WC or TV-IP851WIC connected to a wireless adapter on the PC. SSID: Service Set Identifier.
TRENDnet User’s Guide TV-IP851WC / TV-IP851WIC Network IP Address Mode: Choose a method to assign an IP address to your camera. o Fixed IP – If you want to assign a static or fixed IP address to the camera, you may do so here. Your network administrator should be able to provide you with the necessary details to complete this section. o Dynamic IP (DHCP) – Allows a DHCP server to automatically assign the camera a network address.
TRENDnet User’s Guide TV-IP851WC / TV-IP851WIC Cloud Link Cloud Link: Click the radio button to Enable or Disable cloud server syncing. User User Access Control: Enable this to allow user accounts to connect to the camera. This option also enable/disable the authentication for direct view. For Java mode: http://camera_ip_address/tvjview.htm For ActiveX mode: http://camera_ip_address/tvaview.htm (eg. http://192.168.10.30/tvaview.
TRENDnet User’s Guide Date/Time Synchronized with Time Server: If you have an Internet time server or have an NTP server designated on your network, you can specify the IP address of it here. Ensure that you select the correct time zone for the camera also. Set Manually: If you prefer to manually set the time for the camera, select this mode. You can check the box Synchronized with Computer Time to set the time on the camera to be the same as the computer you are on.
TRENDnet User’s Guide TV-IP851WC / TV-IP851WIC Upload On this screen you can enter details of an FTP Server that you want to upload images from the camera to. Host Address: The IP address of the FTP Server Port Number: The port number to connect to the FTP on, default port is 21. User Name: The user name of the FTP account. Password: The password for the user account on the FTP. Directory Path: The path you want the files to be uploaded to on the FTP.
TRENDnet User’s Guide TV-IP851WC / TV-IP851WIC E-mail This section allows you to configure the email notification settings of your camera. SMTP Server Address: The domain name or IP address of your external mail server. SMTP Port Number: The port number of your mail server, usually this is port 25. Sender’s Email Address: The e-mail address of the person sending the camera snapshots. Recipient’s E-mail Address: The e-mail address of the person receiving the camera snapshots.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Day/Night Mode (for TV-IP851WIC) Tools This section lets you configure the Day/Night vision modes on the IP camera. Auto: The camera automatically detects the level of light and selects night vision or normal mode. Manual: Night mode can be selected on the view video ActiveX and Java tabs. Always Day Mode: Day mode is always selected. Always Night Mode: Night mode is always selected. This option is best used areas of low lighting.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide FTP Server Test When you have set up the FTP Server in the configuration section, you can use this screen to test that the FTP Server settings are correct. Pressing the Test button will make a connection to the FTP Server and upload a file called test_date_time.jpg to the FTP. If the file is not there, you should check that you have entered the FTP details correctly in the configuration section.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Factory Reset If you should need to restore the camera to the factory settings, you can do it from this screen. Clicking Yes will initiate a reboot sequence on the camera. When the camera restarts, you will lose your connection to it. The username and password will also both be set back to the default admin. Wait 1 minute before attempting to reconnect to the camera so that it has time to go through its boot up sequence.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide How to setup/access the camera remotely You can either setup the Dynamic DNS connection via camera itself or your home router. An account from any of the listed DDNS providers is required prior to this operation. Configure DDNS on your Camera 1. Go to Camera’s DDNS Setting page, click Enable to activate the feature. Then select a DDNS provider from the list. 2. Enter your DDNS’s the Host Name, User Name and Password. 3.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide 7. Camera’s login page will appear. Configure DDNS on your router 1. Go to Camera’s DDNS Ports Number section, assign a HTTP port for your camera and click Apply. 2. Login to your router’s web configuration page. 3. Find the Dynamic DNS configuration section. Then click Add to add the application. * Please refer to your router’s user’s manual for detail Virtual Server setting.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide 4. 5. Enable DDNS, fill out the following information and then click Apply. 6. Open another web browser and enter your DDNS domain and camera’s port number. http://yourDomainName:PortNumber 7. The camera login page will appear. Go to Virtual Server* section and create a new entry. Enable: Click Enable Name: Enter the application name (eg. Camera Name) Protocol: Select TCP Private Port: The HTTP port that you assign on your Camera.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Output: 12V, 1.25A external power adapter Technical Specifications TV-IP851WC Camera General Sensor: 1/5” CMOS Sensor Dimension 112 x 110 x 130 mm (4.4 x 4.3 x 5.1 in.) Weight 485 g (1.1 lb) Temperature Operating: 0C ~ 40C (32F ~ 104F) Storage: -25C ~ 70C (-13F ~ 158F) Board Lens Focal Length: 4mm Humidity Max. 90% (non-condensing) F/No: 1.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Receiving Sensitivity Channels 802.11g: 15dBm (typical) Focus Depth: 20 cm ~ infinity 802.11n: 15dBm (typical) View: Horizontal: 38.0 degrees 802.11b: -85dBm at 11Mbps 802.11g: -76dBm at 54Mbps 802.11n: -65dBm at 150Mbps Vertical: 28.7 degrees Diagonal: 46.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Certifications CE, FCC Accounts Up to 64 user accounts Remote Login Remote management supported Internet Explorer 7.0 or higher Backup / Restore Save/retrieve configuration files Firefox 3.5 or higher Settings Requirement Management Interface Safari 4.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide to sunlight or halogen lights. Reposition the Network Camera into a more shaded area immediately as prolonged exposure to bright lights will damage the CMOS sensor. Troubleshooting 1. The Power LED and Ethernet Activity LED do not light up. The power supply or camera might be faulty. Check that the connection to both the power source and the terminal on the back of the camera are secure and that you are using the provided power supply.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Federal Communication Commission Interference Statement EN 60950-1:2006+A11:2009+A1:2010+A12:2011 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
TRENDnet User’s Guide TV-IP851WC / TV-IP851WIC This device is designed to provide uninterrupted monitoring and/or recording. This device does not off power management functionality such as Off mode or Standby mode. © Copyright 2013 TRENDnet. All Rights Reserved.
TV-IP851WC / TV-IP851WIC TRENDnet User’s Guide Česky [Czech] TRENDnet tímto prohlašuje, že tento TV-IP851WC / TV-IP851WIC je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede TRENDnet erklærer herved, at følgende udstyr TVTV-IP851WC / TV-IP851WIC overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
TRENDnet User’s Guide Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. Limited Warranty WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF TRENDNET’S PRODUCTS.