Table of Contents CHAPTER 1 PREFACE.............................................................................................................................. 1-1 ABOUT THIS GUIDE........................................................................................................................................ 1-1 TERMS/USAGE ..............................................................................................................................................
MSTP Global Configuration .................................................................................................................................... 6-8 MSTP Timers Configuration .................................................................................................................................... 6-9 CIST Settings .........................................................................................................................................................
CHAPTER 10 SWITCH STATISTICS ................................................................................................... 10-10 SWITCH STATISTICS LIST............................................................................................................................ 10-10 INTERFACE STATISTICS .............................................................................................................................. 10-10 ETHERNET STATISTICS ................................................
USERNAME .................................................................................................................................................. 13-1 SHOW USERS............................................................................................................................................... 13-1 LISTUSER ....................................................................................................................................................
SSL COMMAND LIST .................................................................................................................................... 19-1 IP HTTP SECURE .......................................................................................................................................... 19-1 DEBUG SSL .................................................................................................................................................. 19-2 SHOW SSL SERVER-CERT ...............
SWITCHPORT INGRESS-FILTER ...................................................................................................................... 26-2 SWITCHPORT PVID ....................................................................................................................................... 26-2 PORTS ........................................................................................................................................................ 26-3 DEBUG VLAN ..............................
LACP PORT-PRIORITY ................................................................................................................................... 30-3 LACP TIMEOUT ............................................................................................................................................. 30-4 LACP WAIT-TIME ........................................................................................................................................... 30-4 SHUTDOWN PORT-CHANNEL...............
SHOW SHOW SHOW SHOW SHOW SHOW MAC-ADDRESS-TABLE AGING-TIME ....................................................................................................... 33-4 MAC-ADDRESS-TABLE COUNT .............................................................................................................. 33-5 MAC-ADDRESS-TABLE DYNAMIC MULTICAST.......................................................................................... 33-5 MAC-ADDRESS-TABLE DYNAMIC UNICAST ......................................
SHOW VLAN TRAFFIC-CLASSES ..................................................................................................................... 40-3 SHOW VLAN PORT CONFIG ............................................................................................................................ 40-4 SHOW DSCP................................................................................................................................................. 40-5 SHOW COSQ ALGORITHM ...............................
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 1 Preface About This Guide This guide provides instructions on how to install and configure the TL2-E284 24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots. This guide is mainly divided into four parts: 1. Hardware Installation: Step-by-step hardware installation procedure. 2. Using Web User Interface: A startup guide to for the command line interface. 3.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 2 Product Introduction Product Introduction The TL2-E284 is a Layer 2 Managed Switch with 24-10/100Mbps Ethernet ports and 4-10/100/1000Mbps Gigabit Ethernet ports shared with 2-10/100/1000Mbps Mini-GBIC slots.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots 10M Link/ACT Shared Gigabit Ethernet (RJ-45) / Mini-GBIC Slot LED 1000M Link/ACT 10/100M Link/ACT Note Amber Color Green Amber Solid 10/20Mbps (Half/Full Duplex) Connected (per port) Blinking 10/20Mbps (Half/Full Duplex)Data Transmitting/Receiving (per port) Off No connection to the port Sequence Definition Solid 2000Mbps (Full Duplex) Connected (per port) Blinking 2000Mbps (Full Duplex) Data Transmitting/
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 3 Hardware Installation This chapter provides unpacking and installation information for TL2-E284. Unpacking Open the shipping carton and carefully unpack its contents. Please consult the packing list located in the User Manual to make sure all items are present and undamaged. If any item is missing or damaged, please contact your local reseller for replacement.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots rack. Figure 3 – Mount the Switch in the rack or chassis Caution Safety Instructions A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 4 Using the Web User Interface After a successful physical installation, you can configure the Switch, monitor the network status, and display statistics using a web browser. Supported Browsers Web The embedded Web-based Management currently supports the following web browsers: A) Internet Explorer 6 or higher B) Netscape 8 or higher C) Mozilla D) Firefox 1.5/2.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 7 – Enter the IP address 192.168.10.200 in the web browser Note The default user name and password are: User Name Password Privilege admin admin 15 guest guest123 1 After login successfully, following page will appear.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Main Configuration Screen. The Device Status provides a real-time switch port link status. By choosing different functions in the Function Tree, you can change all the settings in the Main Configuration Screen. The main configuration screen will show the current status of your Switch by clicking the model name on top of the function tree. To terminate the web management session, click Log Out in the upper right comer.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 5 Configuring System Basic Functions System Basic Function List System Information User Account Management VLAN Management IP Settings IP Authorized Manager SNMP SNMP User/Group Table Configuration SNMP Group Access Table Configuration SNMP View Table Configuration SNMP Community Settings SNMP Host Table SNMP Engine ID Configuration SSH Configuration SSL Configuration System Log Configuration SN
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 9 – System > System Information Parameter Hardware Version Firmware Version Device Name Device Contact Device Location Device Up Time Switch MAC Address Web Aut0 Timeout (180-3600 secs) CLI Auto Timeout (1-18000 secs) Description The hardware version of this device. The firmware version of the device. The name of the device. Default is TL2-E284. The identification information of a contact person.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 11 – System > Management VLAN Parameter Management VLAN Description The VLAN ID of management VLAN. It can be a single VLAN ID from 1 to 4094, a range of VLAN IDs separated by a hyphen (-) ,or a series of non-continuous numbers divided by a comma (,) Click ADD to submit the changes and the Remove button will remove an existed VLAN ID. Note There has to be at least one management VLAN ID exists.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 13 – System > IP Authorized Manager Parameter IP Address Subnet Mask Port List (Incoming) VLANs Allowed Service Allowed Description IP address of authorized manager Subnet mask of the authorized IP address Interface of the authorized administrator is allowed to connect to VLAN ID of the authorized administrator is allowed to connect to.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots SNMP Version Auth-Protocol Priv-Protocol Specify the SNMP version to be used, which can be v1, v2c, or v3. Select „encrypted’ if the encryption for user authentication is needed. Once the encryption is enabled, then you can set the authentication and privilege algorithm and passwords. Specify the authentication algorithm from MD5 or SHA algorithm, and the password.
-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots SNMP View Table Configuration This page is to create a SNMP view, which limits the range of MIB objects that a SNMP administrator can access to. Figure 16 – System > SNMP > View Table Parameter View Name Subtree OID OID Mask View Type Description SNMP view name The object ID of MIB tree The mask of OID included – Includes the object in the list that the SNMP administrator can access.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Click ADD to submit the changes and the Reset button will clear the information. Select and click Delete to remove an existed entry. SNMP Host Table This page is to create a host that can access the device by SNMP protocol. Figure 18 – System > SNMP > Trap Manager Parameter Host IP Address SNMP version Community Name/User Name Description The IP address of a host that can access to the device by SNMP.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 20 – System > SSH Parameter SSH Status Version Cipher Authentication Description Select Enable or Disable to turn on or off the SSH server function. Default is enabled. Specify the SSH version supported. V2 – SSH v2 is supported. This is the default value. V1 & V2 – Both SSH v1 and V2 are supported. To specify SSH Cipher algorithm.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots System Log Configuration This page is to configure system log settings. Figure 22 – System > System Log Parameter Syslog Status Time Stamp Messages Buffered Size (1-200) Syslog Server IP Mail Server IP Receiver Email Address Sender Email Address Facility Logging Level Description The status of syslog server function. Default is enabled. Specifies if time stamp is attached with syslog messages. Default is enabled.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 23 – System > SNTP > Time Settings Parameter Current Time SNTP Status SNTP Poll Interval in Seconds (30-86400) SNTP Primary Server SNTP Secondary Server Time Zone Offset (HH:MM) Year:Month:Day HH:MM:SS Description Current system time. To enable/disable the Simple Network Time Protocol (SNTP) function. Default is disabled.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots To (Month:Day:HH:MM) Click Apply to submit the changes. Configuration Save Configuration This page is used to save the running configuration. Figure 25 – System > Configuration > Save Parameter Save option IP Address File Name Description Options to save the running configuration: Flash Save: Save to the device‟s flash memory with a designated file name.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 26 – System > Configuration > Restore Parameter Restore Option Description Options to restore the startup configuration: No Restore: Applying this option will reset the NV-RAM to default settings. Note: This will only reset the settings in NV-RAM, not the entire device configuration. After rebooting, only the default parameters in NV-RAM will be reset to defaults.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots reset to defaults. Requires a manual device reboot for changes to take effect. Please reference the default NV-RAM parameters below. Default IP Address : 192.168.10.200 Default Subnet Mask: 255.255.255.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Click Upgrade to upgrade the device firmware. Reboot This page is to reboot the system. Figure 28 – System > Reboot Click Reboot to warm start the device. Note 5-14 If the Switch reboots without write the running configurations, the last configuration wrote in NV-RAM will be loaded.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 6 Configuring Layer 2 Management Functions Layer 2 Management Function List Port Manager Port Basic Settings Port Monitoring Port Control VLAN VLAN Basic Information VLAN Port Settings Static VLAN Configuration Dynamic VLAN Dynamic VLAN Global Configuration Dynamic VLAN Port Configuration GARP Timers Configuration MSTP MSTP Global Configuration MSTP Timers Configuration CIST Settings MSTP VLAN Mapping M
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Port Manager Port Basic Settings This page is to configure basic settings of switch ports. Figure 29 – Layer2 Management > Port Manager > Basic Settings Parameter Port Link State Admin State MTU (90-1522) bytes Link Up/Down Trap Description Specify the switch port to be configured. Display the physical connection states of the port. Specify the administrative status of the port. Default is enabled.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 30 – Layer2 Management > Port Manager > Port Monitoring Parameter Status Monitoring Port Port Receive Monitoring Transmit Monitoring Description To enable/disable the port monitoring session on the device. Default is disabled. Specify the source port of the mirror session. Specify the destination port of the mirror session. Monitoring the traffic received from the source port.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 31 – Layer2 Management > Port Manager > Port Control Parameter Port Mode Duplex Speed FlowControl Status FlowControl Status MDI/MDIX Admin Oper Description Specify the switch port to be configured. To enable/disable auto-negotiation function on ports. Default is Auto. To set the port duplex mode. Possible values are: Full: Port runs at full duplex mode. Half: Port runs at half duplex mode. To set the port speed.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots VLAN VLAN Basic Information This page is to configure the basic settings of virtual local area network (VLAN) on the device. Figure 32 – Layer2 Management > VLAN > Basic Information Parameter VLAN Mode Maximum VLAN ID Maximum Supported VLANs Number of VLANs in the System Description Choose from 802.1Q VLAN or Asymmetric VLAN modes. Default is 802.1Q VLAN. Display the maximum VLAN ID can be configured. Default is 4094.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Parameter Port PVID Acceptable Types Description Specifies the switch port which is to be configured. To set the port VLAN ID of the port, all ingress untagged or priority tagged packet from this port will be assign to this VLAN. The range is from 1 to 4094. To configure the acceptable frame type of a port. All: Accepts all kinds of frames.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 35 – Layer2 Management > Dynamic VLAN > Dynamic VLAN Global Configuration Parameter Garp System Control Dynamic VLAN Status Description Choose Start to enable GARP function, and Shutdown to disable it. It is needed for using dynamic VLAN function. Default is Start. To set the status of dynamic VLAN function from Enabled or Disabled. Default is Disabled. Click Apply to submit the changes.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Click Apply to submit the changes. GARP Timers Configuration This page is to set the GARP timers on an interface. Figure 37 – Layer2 Management > Dynamic VLAN > Port Settings Parameter Port No GarpJoinTime (10 ~ 2^30-14)(msecs) GarpLeaveTime (30 ~ 2^31-18)(msecs) GarpLeaveAllTime (40 ~ 2^31-8)(msecs) Description Specify the switch port to be configured. Specify the join time of GARP. Default is 20 milliseconds.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 38 – Layer2 Management > MSTP > Global Configuration Parameter System Control Description To activate or shutdown the MSTP function. Select Start to activate the MSTP function, Shutdown to shutdown MSTP function. To enable or disable the MSTP. Select Enabled to enable the MSTP function, Disabled to disable the MSTP function. Specify the maximum number of MSTP instance allowed. The possible number is 1-64.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Forward Delay Transmit Hold Count Hello Time is 20. Specify the time period in second that a port changes the STP state from blocking to forwarding. The possible value is 4-30. Default is 15. Specify the hold counter to limit maximum transmission rate of the Switch. Default is 3. Specify the time interval in second for a root bridge broadcasts the hello packets to other switches. Possible value is 1-2. Default is 2.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots function, False to disable it. Default is false. Click Apply to submit the changes. MSTP VLAN Mapping This page is to configure the MST Instance and VLAN mapping. Figure 41 – Layer2 Management > MSTP > VLAN Mapping Parameter MSTP Instance ID Add VLAN Delete VLAN Description Specify which MST instance to be mapped. Add a VLAN to the map list of this MST instance. Delete a VLAN from the map list of this MST instance.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 43 – Layer2 Management > MSTP > CIST Port Status Click 1-12, 13-24, 25-28 to display the statistics for corresponding ports. RSTP RSTP Global Configuration This page is to configure the RSTP global settings. Figure 44 – Layer2 Management > RSTP > Global Settings Parameter System Control Status Dynamic Path Calculation Cost Description To activate or shutdown the RSTP function.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 45 – Layer2 Management > RSTP > Basic Settings Parameter Priority Version Tx Hold Count Max Age Help Time Forward Delay Description Specify the bridge priority of spanning tree. Default is 32768. Select the spanning tree compatibility version. The possible options are STP Compatible or RSTP Compatible. Default is RSTP Compatible. Specify the hold counter to limit maximum transmission rate of the Switch.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Parameter Select Port Port Role Port Priority RSTP Status Path Cost Protocol Migration Admin Edge Port Admin Point To Point AutoEdge Detection Restricted Role Restricted TCN Description Select a port to apply the changes. Port ID. Specify the current role of the port. Specify the spanning tree port priority. Possible value is 0-240. Default is 128. To enable or disable the RSTP on this port.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 48 – Layer2 Management > LA > Basic Settings Parameter System Control LA Status System Priority System ID Description To activate or shutdown link aggregation function of the Switch. Select Start to activate link aggregation function, Shutdown to shutdown it. Default is Start. To enable or disable the link aggregation function of the Switch. Select Enabled to enable the LA function, Disabled to disable it.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 50 – Layer2 Management > LA > Port Channel Settings Parameter Port Channel ID Action Type Mode Ports MAC Selection Force MAC Description Select a configured port channel group to submit the changes. To add or delete ports from/to a port channel. Select Add to add ports, Delete to delete one. Specify the mode of this port channel. Possible options are Lacp and Manual.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Parameter Select Port Port Priority Port Identifier Mode Activity Timeout Wait Time (secs) Bundle State Description Select a port to submit the changes. Port ID. Specify the link aggregation port priority of this port. Possible values are 0-65535. Default is 128. Port ID. Specify the mode of this port channel. Possible options are Lacp, Manual and Disable. Specify the LACP mode of the port.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Click Apply to submit the changes. 802.1X 802.1X Basic Settings This page is used to configure the 802.1X authentication global settings. Figure 54 – Layer2 Management > 802.1X > Basic Settings Parameter System Control 802.1X Authentication Authentication Mode Network Access Server ID Protocol Version Description To activate or shutdown 802.1X function of the Switch.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Parameter Select Port Port Control Auth PortStatus Authentication Mode Configured Direction Control Operational Control Direction AuthSM State Restart Authentication Authentication Retry Count Reauth Description Select a port to apply the configuration changes. Port ID. To set the authenticator control on this port. The possible options are: ForceUnauthorized - All traffic is blocked to the port. Auto - Enable the 802.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 56 – Layer2 Management > 802.1X > Timers Parameter Select Port Quiet Period (secs) Transmit Period (secs) Re-authentication Period (secs) Supplicant Timeout (secs) Server Timeout (secs) Description Select a port to apply the configuration changes. Port ID. The period that Switch will not do anything after a failed authentication. Possible value is 0-65535 seconds. Default is 60.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Click Apply to submit the changes to existing user account, Delete to delete one. RADIUS Server Configuration This page is to configure the details of RADIUS server. Figure 58 – Layer2 Management > 802.1X > Radius Settings Parameter Server ID IP Address Shared Secret Server Type Response Time (secs) Retry Count Description Specify the new RADIUS server ID. The possible ID is 1-10.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots IGMP Snooping IGMP Snooping Configuration This page is to configure the IGMP Snooping global settings. Figure 59 – Layer2 Management > IGMP Snooping > Basic Settings Parameter System Control Description To activate or shutdown IGMP snooping of the Switch. Select Start to activate the function, Shutdown to shutdown it. Default is Start. Click Start to start or shutdown the IGMP Snooping globally.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 60 – Layer2 Management > IGMP Snooping > Timer Configuration Parameter Router Port Purge Interval (60~600 Secs) Group-Member Port Purge Interval (130~2335 Secs) Report Forward Interval (1~25 Secs) Group Query Interval (1~5 Secs) Querier Query Interval (60~600 Secs) Description To set the time-out period that an IGMP multicast router port hasn‟t received IGMP router control packet, it will be deleted.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots IGMP Snooping VLAN Router Ports This page is to display the static and dynamic learned IGMP router ports of each VLAN. Figure 62 – Layer2 Management > IGMP Snooping > Router Ports MAC Based Multicast Forwarding Table This page is to display the IGMP group MAC address was learned.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Parameter Select VLAN ID MAC Address Allowed Port Status Description Select which MAC address to apply the configuration changes. VLAN ID of this MAC address belongs to. The MAC address. Specify the port allowed to forward the MAC address. Specify the attribute of this static MAC. The options are: Permanent - The static multicast will keep alive. DeleteOnReset - The static multicast will be deleted after switch reset.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Port Security Settings This page is to configure the port security function for each port. Figure 66 – Layer2 Management > Static MAC Entries > Port Security Settings Parameter Select Port Admin State Max Learning Address (0-64) Description Select a port to apply the configuration changes. Port ID. To enable or disable the port security function. Default is disable. Specify the maximum MAC address number of this port.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 7 Configuring ACL Functions ACL Function List MAC ACL Configuration IP Standard ACL Configuration IP Extended ACL Configuration Classmap Settings Policymap Settings MAC ACL Configuration This page is to create/configure a rule to MAC Access Control List.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots lavc-sca mop-console mop-dump msdos mumps netbios vines-echo vines-ip xns-id others 0x6007(24583). 0x6002(24578). 0x6001(24577). 0x8041(32833). 0x6009(24585). 0x8040(32832). 0x0BAF(2991). 0x0BAD(2989). 0x0807(2055). Insert a custom Ether type (0-65535) to the right column. Click Add to create a new ACL rule, Reset to clear the value.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 68 – ACL > IP Standard ACL Parameter ACL Number Action Source IP Address Subnet Mask Destination IP Address Subnet Mask Port List (Incoming) Description Specify the ACL ID of this rule. The possible ID of IP Standard ACL is 1-1000. Specify the action for packet matched. Select Permit to process the packets, Deny to discard them. Matching packet with a specific source IP address.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 69 – ACL > IP Extended ACL Parameter ACL Number Action Source IP Address Subnet Mask Destination IP Address Subnet Mask Port List (Incoming) Protocol Message Code Message Type Dscp TOS ACK Bit RST Bit Source Port Source Port Mask Destination Port 7-4 Description Specify the ACL ID of this rule. The possible ID of IP Standard ACL is 1001-65535. Specify the action for packet matched.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Destination Port Mask Matching packet with a range of destination port. For example source port 23 with mask FFFE means 22~23. The mask options are: 8000, C000, E000, F000, F800, FC00, FE00, FF00, FF80, FFC0, FFE0, FFF0, FFF8, FFFC, FFFE, FFFF. Click Add to create a new ACL rule, Reset to clear the value.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 70 – ACL > Classmap Parameter Classmap ID ACL ID ACL Type Description Specify the classmap ID. The possible value is 1-65535. Specify the ACL rule ID to bind. Specify the type of the ACL rule. Click Add to create a new classmap, Reset to clear the value. Parameter Select Classmap ID ACL ID ACL Type Description Select a classmap to delete The classmap ID. The ID of binding ACL rule. The type of binding ACL rule.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots In-Profile Action Value Out-Profile Action Out-Profile Value Action Policed-DSCP - Assign a new DSCP value to the packets. Policed-Priority - Assign a new 802.1p priority to the packets. Specify the new value of above. When rewriting DSCP tag, the possible value is 0-63; when rewriting the 802.1p priority, the possible value is 0-7. Specify the action to packets exceed the rate threshold.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 8 Configuring QoS Functions QoS Function List Rate Limiting Storm Control Settings 802.1p Queue Mapping 802.1p Port Priority DSCP Queue Mapping Egress Queue Scheduling Settings Rate Limiting This page is to configure the rate limiting function on each port.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 72 – QoS > Rate Limiting Parameter Select Port Ingress RateLimit (0,64~1000000 Kbps) Egress RateLimit (0,64~1000000 Kbps) Description Select a port to configure rate limiting function. Port ID. Specify the traffic Kbit per second is allowed to be transmitted for an ingress port. 0 means no limit. Specify the traffic Kbit per second is allowed to be transmitted for an egress port. 0 means no limit.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 74 – QoS > 802.1p Parameter Priority 0~7 Description Specify which switch queue to map. The options are Class-0, Class-1, Class-2 and Class-3. Click Apply to submit the changes. 802.1p Port Priority This page is to configure the 802.1p priority for untagged packets receive from each port.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Parameter Select Port User Priority Description Select a port to submit the configuration changes. Port ID. Specify 802.1p priority of untagged packets. Click Apply to submit the changes. Click 1-12, 13-24, 25-28 to configure port priority for corresponding ports. DSCP Queue Mapping This page is to enable/configure the DSCP and queue mapping.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 77 – QoS > Egress Algorithm Parameter Scheduling Algorithm Description Select the algorithm of queue scheduling. The options are: Strict Priority - The traffic in highest queue always process first. Weighted RoundRobin - Using weighted round-robin algorithm to handle packets in priority queues. Default is Strict Priority. Click Apply to submit the changes.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 9 Configuring RMON Functions RMON Function List RMON Basic Settings RMON Statistics Configuration RMON History Configuration RMON Alarms Configuration RMON Events Configuration RMON Basic Settings This page is to enable or disable RMON function Figure 78 – RMON > Global Settings Parameter RMON Status Description To enable or disable RMON function. Default is Disabled. Click Apply to submit the changes.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Click Add to create a new statistics entry, Reset to clear the value. Parameter Select Index Port Drop Events Octets Packets Broadcast Packets Multicast Packets Owner Status Description Select a RMON statistics entry to apply the The index of the RMON statistics collection. The port of the RMON statistics collection. The number of events was dropped due to lack of resources.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Interval Owner Status Specify the time interval for the history collection. Specify the owner of the history entry. Specify the status of this history entry. The options are: Valid - The history entry is valid. Under Creation Invalid - The history entry is invalid and will be deleted. Click Apply to submit the changes. RMON Alarms Configuration To set a RMON alarm to a MIB object.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Interval Variable Sample type Rising Threshold Falling Threshold Rising Event Index Falling Event Index Owner Status The time interval in seconds that alarm monitors the MIB variable. The MIB OID of this alarm entry. The type of the alarm sampling. The options are: Absolute value - To test the MIB variable directly. Delta value - To test the change between samples of a MIB variable.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Community Owner Status SNMP Trap - Generating a trap message when event is triggered. Log and Trap - Generating both log and trap message when event is triggered. Specify the SNMP community string used for the traps. Specify the owner of the alarm entry. Specify the status of this event entry. The options are: Valid - The event entry is valid. Under Creation Invalid - The events entry is invalid and will be deleted.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 83 – Statistics > Interface Click 1-12, 13-24, 25-28 to display the Ethernet related statistics of corresponding ports. Ethernet Statistics This page is to display the Ethernet related statistics of each port. Figure 84 – Statistics > Ethernet Click 1-12, 13-24, 25-28 to display the Ethernet related statistics of corresponding ports.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots MSTP MSTP Information This page is to display current MSTP settings and states of the Switch. Figure 86 – Statistics > MSTP > MSTP Information MSTP CIST Port Statistics This page is to display the MSTP traffic statistics of ports. Figure 87 – Statistics > MSTP > CIST Port Statistics Parameter Clear Counters Description Update – To display the latest statistics information. Clear – To reset all MSTP traffic counters.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots RSTP RSTP Information This page is to display current RSTP setting and states of the Switch. Figure 89 – Statistics > RSTP > RSTP Information RSTP Port Statistics This page is to display the RSTP traffic statistics of ports. Figure 90 – Statistics > RSTP > Port Statistics Parameter Clear Counters Description Update – To display the latest statistics information. Clear – To reset all RSTP traffic counters.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 91 – Statistics > LA > Port LACP Stats Click 1-12, 13-24, 25-28 to display the Link Aggregation neighbours information of corresponding ports. LA Neighbour Statistics Information This page is to display the information of Link Aggregation neibubours.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Click 1-12, 13-24, 25-28 to display the Link Aggregation neighbours information of corresponding ports. 802.1X 802.1X Session Statistics This page is to display the statistics and status of current authenticated users. Figure 93 – Statistics > 802.1X > Session Stats Click 1-12, 13-24, 25-28 to display the statistics for corresponding ports.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 95 – Statistics > IGMP Snooping > Clear Statistics Parameter Clear Vlan Counters Vlan ID Description All – Reset all IGMP Snooping traffic counters. VLAN ID – Reset the IGMP Snooping traffic counter of a VLAN. Choose a VLAN to reset the IGMP Snooping Counters. Click Apply to clear the counters. IGMP Snooping V1/V2 Statistics This page is to display the IGMP traffic statistics snooped by the Switch.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 98 – Statistics > IP > ICMP Statistics RMON This page is to display the RMON Statistics of the Switch. Figure 99 – Statistics > RMON Click First, Prev, Next, Last to see the first, previous, next or last page of the RMON Statistics. MAC Address Table This page is to show the MAC addresses learned in L2 forwarding database.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Figure 100 – Statistics > MAC Address Table Parameter VLAN ID MAC Address Port All Description Display the MAC addresses under a given VLAN. Display a specific MAC address in FDB. Display the MAC addresses learned under a given port. Display all MAC addresses in FDB. Click Show to display the MAC addresses in FDB with given parameter and click Reset to reset the parameter input.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 11 Using the Command-Line Interface Accessing the Switch This system may be managed out-of-band through the console port on the front panel or in-band using Telnet. The user may also choose the web-based management, accessible through a web browser. (See Web UI Reference Guide for details).
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots command or close the emulator program. Telnet Management Users may also access the switch console through Telnet using your PC‟s Command Prompt. To access it from your computer, users must first ensure that a valid connection is made through the Ethernet port of the Switch and your PC, and then click Start > Programs > Accessories > Command Prompt on your computer. Once the console window opens, enter the command telnet 192.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots end interface User EXEC Mode switch> enable disable Interface Configuration Mode switch(config-if)# exit vlan Config-vlan Mode switch(config-vlan)# exit Privileged EXEC Mode switch# configure terminal spanning-tree mst configuration Global Configuration Mode MSTP Configuration Mode switch(config-mst)# exit exit mac access-list extended exit switch(config)# MAC Access List Configuration Mode switch(config-ext-ma
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Configuration Mode interfaces. Config-vlan Mode The VLAN Configuration Mode is used to configure the commands for VLAN interfaces. MSTP Configuration Mode The MSTP Configuration Mode is used to configure multiple spanning tree specific commands.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 12 System Information Command System Information Command List system name system contact system location system web-timeout system cli-timeout default ip address default ip address allocation protocol default mode default restore default restore-file default vlan id set ip http ip http port show system information show nvram show http server status show ip information show line con
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots system contact To enter identification information of a contact person. Command system contact Syntax Description contact info Default Settings SysContact Command Modes Global Configuration Mode User Guidelines Use this command to provide the name and/or other information to identify a contact person who is responsible for the Switch.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command system web-timeout <180-3600 seconds> Syntax Description 180-3600 seconds Default Settings 600 seconds Command Modes Global Configuration Mode User Guidelines This command defines the amount of time the device times out when no user activity occurs on the web interface. Example switch(config)# system web-timeout 3600 Command History Version History 1.00.001 This command was introduced.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command default ip address [ subnet-mask ] [ interface ] Syntax Description ip-address IP address of the default interface subnet-mask subnet mask interface interface-type interface-id Subnet mask of the default interface Default Settings IP address Subnet mask 192.168.10.200 255.255.255.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Note Default mode must be dynamic to make this command effective. default mode To configure the mode that the IP address of default interface is assigned. Command default mode { manual | dynamic } Syntax Description manual dynamic Manual mode. The ip address of default interface is the one configured by „default ip address‟ command. Dynamic mode.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced. default restore-file To configure the default restoration file. Command default restore-file Syntax Description filename Default Settings Iss.conf Command Modes Global Configuration Mode User Guidelines This command is to configure the default restoration file. Example switch(config)# default restore-file restore1.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots set ip http To enable or disable HTTP server. Command set ip http {enable | disable} Syntax Description enable To enable the embedded HTTP server. disable To disable the embedded HTTP server. Default Settings Enable Command Modes Global Configuration Mode Example switch(config)#set ip http enable Command History Version History 1.00.001 This command was introduced.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command show system information Command Modes Privileged EXEC mode Example switch# show system information Hardware Version Firmware Version Switch Name System Contact System Location Logging Option Login Authentication Mode Config Save Status Remote Save Status Config Restore Status Web Timeout Interval Cli Timeout Interval Command History : Rev.A1 : 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced. show http server status To display the HTTP server status. Command show http server status Command Modes Privileged EXEC mode Example switch# show http server status HTTP server status HTTP port is Command History : Enabled : 80 Version History 1.00.001 This command was introduced. show ip information To display the IP information.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots show line console To display the information of current session. Command show line console Command Modes Privileged EXEC mode Example switch# show line console Current Session Timeout (in secs) = 18000 Command History Version History 1.00.001 This command was introduced.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 13 User Account Command User Account Command List username show users listuser username To configure a user account information Command username [password ] [privilege <1-15>] no username Syntax Description username user-name Username password passwd Password privilege 1-15 Privilege level. It is from 1 to 15.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show users Line 0 con Command History User root Peer-Address Local Peer Version History 1.00.001 This command was introduced. listuser To display all existing user information. Command listuser Command Modes Privileged EXEC mode Example switch# listuser USER root guest user Command History 13-2 PRIVILEGE 15 1 1 Version History 1.00.001 This command was introduced.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 14 Management VLAN Command Management VLAN Command List management vlan-list show management vlan management vlan-list To set the VLAN ID for the management VLAN.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 15 IP Settings Command IP Settings Command List release dhcp vlanMgmt renew dhcp vlanMgmt ip arp max-retries arp arp timeout ip address ip address dhcp debug ip dhcp client show ip interface show ip arp release dhcp vlanMgmt To release the DHCP lease of management VLAN interface.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Note The IP address of Management VLAN interface must be assigned by a DHCP server. ip arp max-retries To set the maximum number of ARP request retries. Command ip arp max-retries no ip arp max-retries Syntax Description value (2-10) Number of ARP request retries. Default Settings 3 Command Modes Global Configuration Mode User Guidelines The no form resets the number of retries to default value.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command Modes Global Configuration Mode User Guidelines The no form is to remove the entry. Example switch(config)# arp 10.90.90.100 11:22:33:44:55 vlan 1 Command History Version History 1.00.001 This command was introduced. arp timeout To set the ARP table timeout.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command Modes Interface Configuration Mode User Guidelines The no form will delete the configured IP address. Example switch(config-if)# ip address 20.0.0.1 255.0.0.0 20.0.0.254 Command History Version History 1.00.001 This command was introduced. ip address dhcp To set the IP address of interface to be assigned by DHCP server.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch#debug ip dhcp client all Command History Version History 1.00.001 This command was introduced. show ip interface To display the IP interface information. Command show ip interface Command Modes Privileged EXEC mode User Guidelines This command is to display the IP interface information. Example switch#show ip interface vlanMgmt is up, line protocol is down Internet Address is 0.0.0.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch#show ip route summary Route Source connected static rip bgp ospf Total Command History 15-6 Routes 0 0 0 0 0 0 Version History 1.00.001 This command was introduced.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 16 IP Authorized Manager Command IP Authorized Manager Command List authorized-manager show authorized-managers authorized-manager To set an authorized administrator source IP address, and the services, interfaces, or VLANs that it is allowed to visit. Command authorized-manager ip-source [{ | / }] [interface [
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots User Guidelines The no form removes the administrator from the list. Example switch(config)# authorized-manager ip-source 10.90.90.100 Command History Version History 1.00.001 This command was introduced. show authorized-managers Display the authorized-manager list.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 17 SNMP Command SNMP Command List snmp access snmp community snmp engineid snmp group snmp trapinfo snmp user snmp view snmp-server enable traps snmp authentication snmp-server enable traps snmp-server trap udp-port snmp trap link-status show snmp show snmp community show snmp engineID show snmp group show snmp group access show snmp inform statistics show snmp trapinfo show
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description GroupName Name of SNMP group v1 SNMP version 1 is to be used v2c SNMP version 2v is to be used v3 SNMP version 3 is to be used auth Authentication is required for the SNMP messages noauth Authentication is not required for the SNMP messages authpriv Both authentication and encryption are required for the SNMP messages The SNMP group has read privilege and is allowed to access the specified MIB
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command Modes Global Configuration Mode User Guidelines Before configuring the access settings, the SNMP group has to be created first. Example switch(config)# snmp access oper v2c read operv2readview write operv2writeview notify operv2notifyview nonvolatile Command History Version History 1.00.001 This command was introduced snmp community To create a SNMP community, and the no form removes the community.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command snmp engineid no snmp engineid Syntax Description EngineIdentifier Default Settings 80.00.08.1c.04.46.53 Command Modes Global Configuration Mode User Guidelines SNMP engine ID is unique for each switches Example switch(config)# snmp engineid 80.00.08.1c.04.46.ae Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Default Settings Security Model : v1 Security Name : none Group Name : iso Storage Type : Non-volatile -----------------------------Security Model : v1 Security Name : ReadOnly Group Name : ReadOnly Storage Type : Non-volatile -----------------------------Security Model : v1 Security Name : ReadWrite Group Name : ReadWrite Storage Type : Non-volatile -----------------------------Security Model : v2c Security Name : none Group
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots snmp trapinfo To configure the SNMP Trap setting of a community user, and no form deletes the setting.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots passwd priv DES passwd volatile nonvolatile Authentication password Encryption password Store in volatile memory Store in nonvolatile memory Default Settings User : initial Authentication Protocol : None Privacy Protocol : None Storage Type : Non-volatile -----------------------------User : ReadOnly Authentication Protocol : None Privacy Protocol : None Storage Type : Non-volatile -----------------------------User : ReadWri
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots excluded volatile nonvolatile Excludes the object from the list that the SNMP administrator can access Store in volatile memory Store in nonvolatile memory Default Settings View Name : iso Subtree OID : 1 Subtree Mask : 1 View Type : Included Storage Type : Non-volatile -----------------------------View Name : ReadWrite Subtree OID : 1 Subtree Mask : 1 View Type : Included Storage Type : Non-volatile -----------------------
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots snmp-server enable traps To enable specific SNMP trap message types, and no form disable them.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced snmp trap link-status To enable sending link-status Trap message, and no form disables it Command snmp trap link-status no snmp trap link-status Default Settings Disabled Command Modes Interface Configuration Mode Example switch(config-if)# snmp trap link-status Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch#show snmp 0 SNMP Packets Input 0 Bad SNMP Version errors 0 Unknown community name 0 Get request PDUs 0 Get Next PDUs 0 Set request PDUs 0 SNMP Packets Output 0 Too big errors 0 No such name errors 0 Bad value errors 0 General errors 0 Trap PDUs SNMP Manager-role output packets 0 Drops SNMP 0 0 0 0 Informs: Inform Requests generated Inform Responses received Inform messages Dropped Inform Requests awaiting Ackn
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show snmp community Community Index : NETMAN Community Name : NETMAN Security Name : none Context Name : Transport Tag : Storage Type : Non-volatile Row Status : Active -----------------------------Community Index : PUBLIC Community Name : PUBLIC Security Name : none Context Name : Transport Tag : Storage Type : Non-volatile Row Status : Active -----------------------------Community Index : oper Community Name
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command Modes 17-13 Privileged EXEC Mode
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show snmp group Security Model : v1 Security Name : none Group Name : iso Storage Type : Non-volatile Row Status : Active -----------------------------Security Model : v1 Security Name : ReadOnly Group Name : ReadOnly Storage Type : Non-volatile Row Status : Active -----------------------------Security Model : v1 Security Name : ReadWrite Group Name : ReadWrite Storage Type : Non-volatile Row Status : Active
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show snmp group access Group Name : iso Read View : iso Write View : iso Notify View : iso Storage Type : Non-volatile Row Status : Active -----------------------------Group Name : iso Read View : iso Write View : iso Notify View : iso Storage Type : Non-volatile Row Status : Active -----------------------------Group Name : initial Read View : restricted Write View : restricted Notify View : restricted Storage
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Read View : ReadWrite Write View : ReadWrite Notify View : ReadWrite Storage Type : Non-volatile Row Status : Active ---------------------------Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots show snmp user To display the SNMP user information Command show snmp user Command Modes Privileged EXEC Mode Example switch# show snmp user Engine ID : 80.00.08.1c.04.46.53 User : initial Authentication Protocol : None Privacy Protocol : None Storage Type : Non-volatile Row Status : Active -----------------------------Engine ID : 80.00.08.1c.04.46.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command show snmp viewtree Command Modes Privileged EXEC Mode Example switch# show snmp viewtree View Name : iso Subtree OID : 1 Subtree Mask : 1 View Type : Included Storage Type : Non-volatile Row Status : Active -----------------------------View Name : ReadWrite Subtree OID : 1 Subtree Mask : 1 View Type : Included Storage Type : Non-volatile Row Status : Active -----------------------------View Name : restricted Subtr
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 18 SSH Command SSH Command List ssh ip ssh debug ssh show ip ssh ssh To activate the SSH server function on the switch. The no format is to turn it off. Command ssh {enable | disable} Syntax Description enable To turn on the SSH server function. disable To turn off the SSH server function.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description version compatibility cipher ([des-cbc] [3des-cbc]) auth ([hmac-md5] [hmac-sha1]) The supported version of SSH. To configure SSH Cipher algorithm. User can choose from DES (Data Encryption Standard) or 3DES (Triple_Data Encryption Standard) encryption algorithm in CBC (Cipher Blocking Chain) mode. To configure authentication encryption algorithm.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description all Enable or disable all categories of messages. shut Shutdown messages. mgmt Management messages. data Data Path messages. ctrl Control panel messages. dump Packet Dump messages. resource All resource messages except for buffer. failall Failure messages. buffer Buffer messages. server SSH server messages. Default Settings Disabled.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 19 SSL Command SSL Command List ip http secure debug ssl show ssl server-cert show ip http secure server status ip http secure To activate SSL server on the switch and configure Cipher and key settings. The no form will deactivate SSL server and all settings.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Default Settings SSL server is disabled. Cipher Suite is RSA-DES-SHA1, RSA-3DES-SHA1, and RSA-EXP1024-DES-SHA1 Command Modes Global Configuration Mode Example switch(config)# ip http secure ciphersuite rsa-null-md5 Command History Version History 1.00.001 This command was introduced debug ssl To enable the debug messages of SSL. The no format will reset all settings.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots show ssl server-cert To display SSL server certification Command show ssl server-cert Command Modes Privileged EXEC Mode User Guidelines The server certification has to be created first.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots show ip http secure server status To display the SSL server status Command show ip http secure server status Command Modes Privileged EXEC Mode Example switch# show ip http secure server status HTTP secure server status : Disabled HTTP secure server ciphersuite : RSA-NULL-MD5: Command History 19-4 Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 20 System Log Command System Log Command List copy logs logging mailserver clear logs show logging show email alerts copy logs Backup the system log to a remote tftp server Command copy logs tftp://ip-address/filename Syntax Description tftp://ip-address/filename Command Modes Global Configuration Mode User Guidelines The maximum lengths of filename are 32 characters.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description ip-address IP address of the syslog server buffered size (1-200) The size of internal logging buffer console Enable logging to the console Facility local0~7 trap Specifies the facility that is indicated in the message.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description ip-address Default Settings No mail server is configured. Command Modes Global Configuration Mode Example switch(config)# mailserver 172.17.0.201 Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show logging System Log Information ---------------------Syslog logging : enabled(Number of messages 0) Console logging : disabled(Number of messages 0) TimeStamp option : enabled Trap logging : Informational Log server IP : 20.0.0.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 21 SNTP Command SNTP Command List clock set set sntp set sntp dst sntp dst sntp poll-interval sntp primary-ip sntp secondary-ip sntp timezone show clock show sntp clock set To set the system time.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description enable Enables the SNTP. disable Disables the SNTP. Default Settings Disable Command Modes Global Configuration Mode Example switch(config)# set sntp enable Command History Version History 1.00.001 This command was introduced set sntp dst To enable/disable the Daylight Saving Time (DST) function of SNTP.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description from Time that DST startis from january ~ december Specify the month that DST starts. day (1-31) Specify the day that DST starts. hour (0-23) Specify the hour that DST starts. minute (0-59) Specify the minute that DST starts. to Time that DST ends from january ~ december Specify the month that DST ends. day (1-31) Specify the day that DST ends. hour (0-23) Specify the hour that DST endts.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command sntp primary-ip Syntax Description ip-address Command Modes Global Configuration Mode Example switch(config)# sntp primary-ip 172.17.5.254 Command History Version History 1.00.001 This command was introduced Specify the IP address of the primary SNTP server. sntp secondary-ip To set the secondary SNTP server IP address.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch(config)# sntp timezone offset – 8 0 Command History Version History 1.00.001 This command was introduced show clock To display the system date and time. Command show clock Command Modes Privileged EXEC Mode Example switch# show clock Wed Dec 23 18:04:11 2009 Command History Version History 1.00.001 This command was introduced show sntp To display current SNTP settings.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 22 Configuration Command Configuration Command List write copy startup-config copy erase write To save the running configuration. Command write { flash:filename tftp://ip-address/filename } Syntax Description flash:filename | startup-config | Write to a designated flash driver with designated file name. Write to start up configuration.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# copy startup-config flash:backupstarup Command History Version History 1.00.001 This command was introduced copy To replace the startup configuration by a another configuration file in remote TFTP site or NV-RAM.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 23 Firmware Upgrade Command Firmware Upgrade Command List archive download-sw /overwrite archive download-sw /overwrite To download the image from a TFTP server. Command archive download-sw /overwrite tftp://ip-address/filename Syntax Description tftp://ip-address /filename Command Modes Privileged EXEC Mode Example switch# archive download-sw tftp://172.17.5.111/image.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 24 Reboot Command Reboot Command List reload reload Reboot the Switch Command reload Command Modes Privileged EXEC Mode Example switch# reload Command History Version History 1.00.001 This command was introduced Note 24-1 If the Switch reboots without write the running configurations, the last configuration wrote in NV-RAM will be loaded.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 25 Port Manager Command Port Manager Command List monitor session negotiation speed duplex flowcontrol mdi show flow-control show mdi-mdix show port-monitoring monitor session To enable and configure the port mirroring function.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command Modes Global Configuration Mode User Guidelines 1. Using no form to disable the port mirroring function. 2. Destination port and source port have to be counfigured separately. 3. A port-channel can be mirrored, however, a port-channel port cannot.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots User Guidelines The configured port speed and duplex settings only takes effect when auto-negotiation disabled. Example switch(config-if)# speed 100 Command History Version History 1.00.001 This command was introduced duplex To set the port duplex mode. Command duplex { full | half } Syntax Description full Port runs at full duplex mode. half Port runs at half duplex mode.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced mdi To set MDI or MDIX mode for ports. Command mdi { auto | mdi | mdix } Syntax Description auto Port performs the auto MDI/MDIX function. mdi Port fixed at MDI mode. mdix Port fixed at MDIX mode. Default Settings Auto Command Modes Interface Configuration Mode Example switch(config-if)# mdi mdi Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots show mdi-mdix To display the MDI/MDIX setting on ports. Command show mdi-mdix [ interface ] Syntax Description interface interface-type interface-id Command Modes Privileged EXEC Mode User Guidelines System will disply MDI/MDIX setting for all ports when executing the command without port parameter.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command show port-monitoring Command Modes Privileged EXEC Mode Example switch# show port-monitoring Port Monitoring is enabled Monitor Port : Fa0/9 Port ---Fa0/1 Fa0/2 Fa0/3 Fa0/4 Fa0/5 Command History 25-6 Ingress-Monitoring -----------------Enabled Disabled Disabled Disabled Disabled Egress-Monitoring ----------------Enabled Disabled Disabled Disabled Disabled Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 26 VLAN Command VLAN Command List vlan switchport acceptable-frame-type switchport ingress-filter switchport pvid ports debug vlan show vlan show vlan device info show vlan port config vlan To create a VLAN or enter a VLAN interface configured.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description all Accepts all kinds of frames. tagged Accepts only tagged frames untaggedAndPrioritytagged Accepts only untagged frames and frames with priority tag. Default Settings all Command Modes Interface Configuration Mode Example switch(config-if)# switchport acceptable-frame-type tagged Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description vlan-id(1-4094) Default Settings 1 Command Modes Interface Configuration Mode Example switch(config-if)# switchport pvid 100 Command History Version History 1.00.001 This command was introduced Specify the PVID of the port. ports To apply the VLAN membership to ports or port-channels. Command ports ([ <0/a-b,0/c,...>] [ <0/a-b,0/c,...
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots debug vlan To enable the debug mode for VLAN. Command debug vlan { global | [{fwd | priority | redundancy} [initshut] [mgmt] [data] [ctpl] [dump] [os] [failall] [buffer] [all]]} no debug vlan { global | [{fwd | priority | redundancy} [initshut] [mgmt] [data] [ctpl] [dump] [os] [failall] [buffer] [all]]} Syntax Description global Displays the global debug messages for multiple instances.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command show vlan [brief | id | summary] Syntax Description brief Display the brief of VLAN information. id Limited a range of VLAN to display the information. The vlan-range format is a-b, b should be larger than a. Display the number of VLAN.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example Single Instance: switch# show vlan brief Vlan database ------------Vlan ID Member Ports : 1 : Fa0/1, Fa0/2, Fa0/3, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16, Fa0/17, Fa0/18, Fa0/19, Fa0/20, Fa0/21, Fa0/22, Fa0/23, Fa0/24 Gi0/1, Gi0/2, Gi0/3, Gi0/4 Untagged Ports : Fa0/1, Fa0/2, Fa0/3, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, F
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Name : Status : Dynamic Gvrp ---------------------------------------------------Command History Version History 1.00.001 This command was introduced show vlan device info To display the VLAN settings and detailed information of the device.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example Single Instance: switch# show vlan device info Vlan device configurations -------------------------Vlan Status : Enabled Vlan Oper status : Enabled Gvrp status : Disabled Gvrp Oper status : Disabled Bridge Mode : Customer Bridge Traffic Classes : Enabled Vlan Operational Learning Mode : IVL Version number : 1 Max Vlan id : 4095 Max supported vlans : 256 Multiple Instance: switch# show vlan device info Switch default V
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command Modes Privileged EXEC Mode User Guidelines System will display VLAN configurations for all port when executing the command without a port parameter.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example Single Instance: switch# show vlan port config port fa 0/1 Vlan Port configuration table ------------------------------Port Fa0/1 Port Vlan ID : 1 Port Acceptable Frame Type : Admit All Port Ingress Filtering : Enabled Port Mode : Hybrid Port Gvrp Status : Enabled Port Gvrp Failed Registrations : 0 Gvrp last pdu origin : 00:00:00:00:00:00 Port Restricted Vlan Registration : Disabled Default Priority : 0 --------------
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Default Priority : 0 ------------------------------------------------------Port Fa0/3 Port Vlan ID : 1 Port Acceptable Frame Type : Admit All Port Ingress Filtering : Disabled Port Mode : Hybrid Port Gvrp Status : Enabled Port Gmrp Status : Enabled Port Gvrp Failed Registrations : 0 Gvrp last pdu origin : 00:25:64:93:1c:35 Port Restricted Vlan Registration : Disabled Port Restricted Group Registration : Disabled Mac Based Supp
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 27 Dynamic VLAN Command Dynamic VLAN Command List set gvrp set port gvrp set garp timer vlan restricted shutdown garp debug garp show garp timer set gvrp To global enable/disable GVRP function. Command set gvrp { enable | disable } Syntax Description enable Enables GVRP globally. disable Disable GVRP globally.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description interface-type interface-id enable Specify which port to enable GVRP function. Interface-type including Fa (Fast Ethernet) or Gi (Gigabit Ethernet). Interface-id is slot/port number. Enables GVRP on the port. disable Disables GVRP on the port.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots vlan restricted To enable/disable the restricted VLAN on an interface. Command vlan restricted {enable | disable} Syntax Description enable Enalbes VLAN restriction. disable Disables VLAN restriction. Default Settings Disable Command Modes Interface Configuration Mode User Guidelines When a port enables VLAN restriction, only static configured VLAN can be learnt from this interface.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots debug garp To enable the debug mode of GARP function. Command debug garp { global | [{protocol | gvrp | redundancy} [initshut] [mgmt] [data] [ctpl] [dump] [os] [failall] [buffer] [all]]} no debug garp { global | [{protocol | garp | redundancy} [initshut] [mgmt] [data] [ctpl] [dump] [os] [failall] [buffer] [all]] Syntax Description global protocol Displays the global GARP debug messages for multiple instances.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description port interface-type interface-id Command Modes Privileged EXEC Mode User Guidelines System will display timer settings for all port when executing the command without a port parameter. Example switch# show garp timer port fa 0/1 Specify which port to show GVRP timer setting. Interface-type including Fa (Fast Ethernet) or Gi (Gigabit Ethernet). Interface-id is slot/port number.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 28 RSTP Command RSTP Command List spanning-tree spanning-tree compatibility spanning-tree mode spanning-tree pathcost dynamic spanning-tree transmit hold-count spanning-tree timers spanning-tree auto-edge spanning-tree restricted-role spanning-tree restricted-tcn spanning-tree interface attributes shutdown spanning-tree clear spanning-tree counters debug spanning-tree show spanning
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command spanning-tree compatibility {stp|rst|mst} no spanning-tree compatibility Syntax Description stp Compatible wirh STP. rst Compatible with RSTP. mst Compatible with MSTP. Default Settings rst Command Modes Global Configuration Mode User Guidelines Using no form to reset the STP compatibility to default. Example switch(config)# Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots spanning-tree pathcost dynamic To enable the dynamic pathcost according to the port speed.. Command spanning-tree pathcost dynamic no spanning-tree pathcost dynamic Default Settings Disable Command Modes Global Configuration Mode User Guidelines 1. If the cost has been configured on a CIST or a RSTP interface, then this command won‟t take effect on those interfaces. 2.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots spanning-tree timers To set the timer of spanning tree. Command spanning-tree {forward-time | max-age } | hello-time no spanning-tree { forward-time | hello-time | max-age } Syntax Description forward-time seconds(4-30) hello-time seconds(1-2) max-age seconds(6-40) The time period that a port changes the STP state from blocking to forwarding.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced spanning-tree restricted-role To enable the root guard function to prevent the port becoming a root port. Command spanning-tree restricted-role no spanning-tree restricted-role Default Settings Disable Command Modes Interface Configuration Mode User Guidelines Using no form to disable the root guard function.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots spanning-tree interface attributes To set detailed spanning attrebutes to ports. Command spanning-tree {cost | disable | link-type {point-to-point | shared} | portfast | port-priority } no spanning-tree {cost | disable | link-type | portfast | port-priority} Syntax Description cost value(0-200000000) disable Specify the pathcost of this port.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch(config)# shutdown spanning-tree Command History Version History 1.00.001 This command was introduced clear spanning-tree counters To clear the spanning tree counters. Command clear spanning-tree counters Command Modes Global Configuration Mode Example switch(config)# clear spanning-tree counters Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description global Displays the MSTP global debug messages. all Displays all RSTP/MSTP debug messages. errors Displays the error code debug messages. init-shut Displays the initial and shutdown debug messages. management Displays the management related debug messages. memory Displays the memory related debug messages. bpdu Displays the BPDU related debug messages.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots show spanning-tree To display the spanning port states, statistics, settings and detailed information. Command show spanning-tree method }] Syntax Description summary Display the summary of port states. blockedports Display current block port number. pathcost method Display the pathcost method setting.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example Single Instance: switch# show spanning-tree Root Id Priority 32768 Address 00:18:8b:bf:75:30 Cost 0 Port 0 [0] This bridge is the root Max age 20 Sec, forward delay 15 Sec Spanning tree Protocol Enabled Bridge Id Priority 32768 Address 00:18:8b:bf:75:30 Hello Time 2 sec, Max Age 20 sec, Forward Delay 15 sec Dynamic Path Cost is Enabled Name Role State Cost Prio Type ---------------------Fa0/1 Designated Forwarding 200
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots S-VLAN Component: MST00 is executing the mstp compatible Multiple Spanning Tree Protocol Bridge Id Priority 32768 Address 00:18:8b:bf:75:30 Hello Time 2 sec, Max Age 20 sec, Forward Delay 15 sec Dynamic Path Cost is Enabled Name Role State Cost Prio Type ---------------------Fa0/1 Designated Forwarding 200000 128 SharedLan Fa0/2 Designated Forwarding 200000 128 SharedLan Fa0/3 Designated Forwarding 200000 128 SharedLan Fa0/4 D
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots show spanning-tree active To display the spanning tree information on active ports. Command show spanning-tree active [detail] Syntax Description detail Command Modes Privileged EXEC Mode 28-12 Display the details of spanning tree bridge.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example Single Instance: switch# show spanning-tree active Root Id Priority 8192 Address 00:74:24:00:01:00 Cost 2000000 Port Fa0/1 Hello Time 2 Sec, Max Age 20 Sec, Forward Delay 15 Sec Spanning Tree Enabled Protocol RSTP Bridge Id Priority 32768 Address 00:18:8b:bf:75:30 Hello Time 2 sec, Max Age 20 sec, Forward Delay 15 sec Name Role State Cost Prio Type ----------------- -----Fa0/1 Root Forwarding 2000000 128 SharedLan swi
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots show spanning-tree bridge To display the spanning tree bridge settings. Command show spanning-tree bridge [{ address | forward-time | hello-time | id |max-age | protocol | priority | detail }] Syntax Description address Display the MAC address of spanning tree bridge. forward-time Display the current setting of spanning tree forward time. hello-time Display the current setting of spanning tree hello time.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example Single Instance: switch# show spanning-tree bridge Bridge ID HelloTime MaxAge FwdDly Protocol ----------------- ------ ------ -------80:00:00:74:24:00:01:00 20 2000 15 rstp switch# show spanning-tree bridge address Bridge Address is 00:74:24:00:01:00 switch# show spanning-tree bridge forward-time Bridge Forward delay is 15 sec switch# show spanning-tree bridge hello-time Bridge Hello Time is 2 sec switch# show spann
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots MST00 00:74:24:00:01:00 Switch - cust1 MST00 00:74:24:00:01:02 Command History Version History 1.00.001 This command was introduced show spanning-tree interface To display the spanning tree states, statistics, settings information on a port.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example Single Instance: switch# show spanning-tree interface fa 0/1 Role ---Root State ----Forwarding Cost Prio ------2000000 128 Type ---SharedLan switch# show spanning-tree interface fa 0/1 cost Port cost is 2000000 switch# show spanning-tree interface fa 0/1 priority Port Priority is 128 switch# show spanning-tree interface fa 0/1 portfast PortFast is enabled switch# show spanning-tree interface fa 0/1 rootcost Root C
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots BPDUs : sent 1479 , recieved 3458 Multiple Instance: switch# show spanning-tree interface fa 0/1 Switch Role ---Root - default State ----Forwarding Cost Prio ------2000000 128 Type ---SharedLan switch# show spanning-tree interface fa 0/1 cost Port cost is 2000000 Switch - default switch# show spanning-tree interface fa 0/1 priority Switch – default Port Priority is 128 switch# show spanning-tree interface fa 0/1 portfast S
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots switch# show spanning-tree interface fa 0/1 detail Switch – default Port 1 [Fa0/1] is Root , Forwarding Port PathCost 2000000, Port Priority 128, Port Identifier 128.1 Designated Root has priority 8192, address 00:18:8b:bf:75:30 Designated Bridge has priority 8192, address 00:18:8b:bf:75:30 Designated Port Id is 128.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show spanning-tree root Root ID RootCost MaxAge FwdDly RootPort --------------------- ------ -------80:00:08:00:1f:3f:73:26 0 20 15 0 switch# show spanning-tree root address Root Bridge Address is 08:00:1f:3f:73:26 switch# show spanning-tree root cost Root Cost is 2000000 switch# show spanning-tree root forward-time Forward delay is 15 sec switch# show spanning-tree root hello-time Hello Time is 2 sec switch#
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 29 MSTP Command MSTP Command List spanning-tree priority spanning-tree mst configuration spanning-tree mst max-hops spanning-tree mst max-instance instance name revision spanning-tree mst hello-time show spanning-tree mst show spanning-tree mst interface show spanning-tree mst configuration spanning-tree priority To set the bridge priority of spanning tree.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command spanning-tree mst configuration Command Modes Global Configuration Mode User Guidelines Spanning tree mode must be MST before entering the MSTP Configuration Mode. Example switch(config)# spanning-tree mst configuration switch(config-mst)# Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Default Settings 64 Command Modes Global Configuration Mode User Guidelines Using no form to reset the max instance number to default. Example switch(config)# spanning-tree mst max-instance 16 Command History Version History 1.00.001 This command was introduced instance To assign VLAN range to a MST instance.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Default Settings 00: 00: 00: 00: 00: 00 Command Modes MSTP Configuration Mode User Guidelines Using no form the reset the name to default. Example switch(config-mst)# name trendnet Command History Version History 1.00.001 This command was introduced revision To set the revision number for the MST reigon.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command Modes Interface Configuration Mode User Guidelines Use no form to reset the hello time value to default. Example switch(config-if)# spanning-tree mst hello-time 1 Command History Version History 1.00.001 This command was introduced show spanning-tree mst To display the information of MST instances.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced show spanning-tree mst interface To display the MSTP status, statistics and current setting on interfaces.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots show spanning-tree mst configuration To display current multiple spanning tree settings.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 30 Link Aggregation Command Link Aggregation Command List set port-channel lacp system-priority port-channel load-balance channel-group lacp port-priority lacp timeout lacp wait-time shutdown port-channel show etherchannel show lacp show interfaces etherchannel set port-channel To enable or disable port channel function of the Switch.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description 0-65535 Default Settings 32768 Command Modes Global Configuration Mode User Guidelines The system priority decides the standby or active links in a aggregation when the number of member port exceeds the maximum number of the etherchannel that Switch supported. Example switch(config)# lacp system-priority 1 Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced channel-group To join a port to a channel group. Command channel-group mode {active | passive | on} no channel-group Syntax Description channel-group-n umber(1-65535) mode active Specify which channel group to configure. mode passive LACP negotiation starts only when LACP packet is received.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots User Guidelines The port priority decides the standby or active links in a aggregation when the number of member port exceeds the maximum number of the etherchannel that Switch supported. Example switch(config-if)# lacp port-priority 1 Command History Version History 1.00.001 This command was introduced lacp timeout To choose the LACP timeout period when no packet receive from peer..
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch(config-if)# lacp wait-time 0 Command History Version History 1.00.001 This command was introduced shutdown port-channel To shutdown the port channel group. Command shutdown port-channel no shutdown port-channel Default Settings Active Command Modes Global Configuration Mode User Guidelines Using no form to reactivate the port channel group.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots User Guidelines 30-6 System will display the global information and the summary of all port channel groups when executing this command without any keyword.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show etherchannel Port-channel Module Admin Status is enabled Port-channel Module Oper Status is enabled Port-channel System Identifier is 00:74:24:00:01:00 Maximum ports per Port Channel is 8 with maximum 8 active ports Channel Group Listing --------------------Group : 1 ---------Protocol : LACP switch# show Port-channel Port-channel Port-channel etherchannel 1 detail Module Admin Status is enabled Module Op
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Default Port = None switch# show etherchannel 1 load-balance Channel Group Listing --------------------Group : 1 ---------Source & Destination MAC Address switch# show etherchannel 1 port Channel Group Listing --------------------Group: 1 ---------Protocol :LACP Ports in the Group -----------------Port : Gi0/1 ------------Port State = Down, Not in Bundle Channel Group : 1 Mode : Active Pseudo port-channel = Po1 LACP port-prior
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Number of Ports = 1 HotStandBy port = null Port state = Port-channel Ag-Not-Inuse Protocol = LACP MAC selection = Dynamic Default Port = None switch# show etherchannel 1 summary Port-channel Module Admin Status is enabled Port-channel Module Oper Status is enabled Port-channel System Identifier is 00:74:24:00:01:00 Maximum ports per Port Channel is 8 with maximum 8 active ports Flags: D - down P - in port-channel I - stand-al
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command Modes Privileged EXEC Mode Example switch# show lacp 1 counters LACPDUs LACPDUs Port Sent Recv Pkts Err -----------------------------------------------Channel group: 1 -----------------Gi0/1 788 704 0 0 Gi0/2 636 596 0 0 switch# show lacp 1 neighbor Flags: A - Device is in Active mode P - Device is in Passive mode Channel group 1 neighbors Port Gi0/1 ---------Partner System ID : 08:01:02:03:04:05 Flags : P LACP Part
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command show interfaces etherchannel Syntax Description interface-type interface-id Command Modes Privileged EXEC Mode User Guidelines System will display the etherchannel information for all ports and also the etherchannel global information when executing this command without a interface parameter. 30-11 [ ] Specify the information of which port to show.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show interface gi 0/1 etherchannel Port : Gi0/1 ------------Port State = Down, Not in Bundle Channel Group : 1 Mode : Active Pseudo port-channel = Po1 LACP port-priority = 128 LACP Wait-time = 2 secs LACP Admin Port = 25 LACP Activity : Active LACP Timeout : Long Aggregation State : Aggregation, Defaulted LACP Port Admin Oper Port Port Port State Priority Key Key Number State ----------------------------------
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 31 802.1X Command 802.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots dot1x system-auth-control To enable 802.1X authentication on the Switch. Command dot1x system-auth-control no dot1x system-auth-control Default Settings Disable Command Modes Global Configuration Mode User Guidelines Using no form to disable the 802.1X authentication. Example switch(config)# dot1x system-auth-control Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command dot1x local-database password permission {allow | deny} [] [interface ] no dot1x local-database Syntax Description username Specify the user name of a local database entry. password password permission allow Specify the password of a local database entry.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description ip-address Specify the IP address of RADIUS server. timeout 1-120 Specify the time period that a client waits for the response from the RADIUS server before re-sending the request. The maximum number that a client re-sends the request when there is no response from RADIUS server. The encryption key for the communication of RADIUS server.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots dot1x default To configure 802.1X with default values on the port. Command dot1x default Default Settings Per-interface 802.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots User Guidelines Using no form to reset the number of retry to default. Example switch(config-if)# dot1x max-req 10 Command History Version History 1.00.001 This command was introduced dot1x max-start To set the maximum EAPOL retries of the authenticator.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Default Settings Force-authorized Command Modes Interface Configuration Mode Example switch(config-if)# dot1x port-control auto Command History Version History 1.00.001 This command was introduced dot1x reauthenitcation To enable the periodic re-authentication on ports.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description quiet-period value (0-65535) reauth-period value (1-65535) server-timeout value (1-65535) supp-timeout value (1-65535) tx-period value (1-65535) - The period that Switch will not do anything after a failed authentication. The period between re-authentication attempts. The period that Switch waits for the re-transmission to the RADIUS server.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots debug dot1x To enable the debug mode of 802.1X authentication. Command debug dot1x {all | errors | events | packets | state-machine | redundancy} no debug dot1x {all | errors | events | packets | state-machine | redundancy} Syntax Description all Displays all 802.1X debug messages.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description all Displays all RADIUS debug messages. errors Displays the error code debug messages. events Displays the event related debug messages. packets Displays the packet related debug messages. responses Displays the server response related debug messages. timers Displays the timer related debug messages.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show dot1x Sysauthcontrol Module Oper Status Dot1x Protocol Version Dot1x Authentication Method Nas ID = Disabled = Disabled = 2 = Local = fsNas1 switch# show dot1x interface fa 0/1 Dot1x Info for Fa0/1 --------------------AuthMode = PORT-BASED PortStatus = AUTHORIZED AuthSM State = INITIALIZE BendSM State = INITIALIZE AuthPortStatus = AUTHORIZED AdminControlDirection = BOTH OperControlDirection = BOTH MaxRe
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Fa 0/22, Fa 0/23, Fa 0/24 Permission : Allow --------------------------------Command History Version History 1.00.001 This command was introduced show radius server To display current status and settings of RADIUS servers Command show radius server Command Modes Privileged EXEC Mode Example switch# show radius server Radius Server Host Information -----------------------------Index : 1 Server address : 172.17.5.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show radius statistics Radius Server Statistics ------------------------Index : 1 Radius Server Address : 172.17.5.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 32 IGMP Snooping Command IGMP Command List ip igmp snooping ip igmp snooping clear counters ip igmp snooping group-query-interval ip igmp snooping mrouter ip igmp snooping mrouter-time-out ip igmp snooping port-purge-interval ip igmp snooping querier-query-interval ip igmp snooping report-forward ip igmp snooping report-suppression-interval ip igmp snooping retry-count ip igm
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots ip igmp snooping clear counters To clear the IGMP snooping. counters Command ip igmp snooping clear counters [Vlan ] Syntax Description Vlan vlanid (1-4094) Command Modes Global Configuration Mode User Guidelines System will clear all IGMP counters when executing this command without a VLAN parameter.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command ip igmp snooping mrouter <0/a-b, 0/c, ...> no ip igmp snooping mrouter <0/a-b, 0/c, ...> Syntax Description interface-type 0/a-b, 0/c, ... Command Modes Config-vlan Mode User Guidelines Using no form to delete a static IGMP multicast router port. Example switch(config-vlan)# ip igmp snooping mrouter int fa 0/1 Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command ip igmp snooping port-purge-interval <(130 - 1225) seconds> no ip igmp snooping port-purge-interval Syntax Description (130-1225) seconds Default Settings 260 seconds Command Modes Global Configuration Mode User Guidelines Using no form to reset the port purge interval to default. Example switch(config)# ip igmp snooping port-purge-interval 150 Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command ip igmp snooping report-forward {all-ports | router-ports} no ip igmp snooping report-forward Syntax Description all-ports To forward IGMP reports to all ports. router-ports To forward IGMP reports to router ports. Default Settings Router ports Command Modes Global Configuration Mode User Guidelines Using no form to reset the forwarding port to default.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots received a IGMPv2 leave message. Command ip igmp snooping retry-count <1 - 5> no ip igmp snooping retry-count Syntax Description 1 - 5 Default Settings 2 Command Modes Global Configuration Mode User Guidelines Using no form to reset the retry counter to default. Example switch(config)# ip igmp snooping retry-count 5 Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command ip igmp snooping fast-leave no ip igmp snooping fast-leave Default Settings Disable Command Modes Config-vlan Mode Example switch(config-vlan)# ip igmp snooping fast-leave Command History Version History 1.00.001 This command was introduced ip igmp snooping querier To configure the switch as the IGMP querier in a VLAN.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots User Guidelines Using no form the restart the snooping. Example switch(config)# shutdown snooping Command History Version History 1.00.001 This command was introduced debug ip igmp snooping To enable the debug mode of IGMP snooping.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced show ip igmp snooping To display current settings of IGMP snooping function.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced show ip igmp snooping globals To display the current global settings of IGMP snooping function.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# sh ip igmp snooping groups vlan 1 Group 239.255.255.250 Snooping Group information ----------------------------Index: 1 Index: 2 Index: 3 VLAN ID:1 Group Address: 239.255.255.250 Filter Mode: EXCLUDE Exclude sources: None Receiver Ports: Fa0/9 Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example Single Instance: switch# show ip igmp snooping mrouter Vlan Ports ----- -----1 Gi0/1(dynamic), Gi0/2(static) 2 Gi0/3(static), Gi0/4(dynamic) Multiple Instance: switch# show ip igmp snooping mrouter Switch cust1 Vlan Ports ----- -----1 Gi0/1(static) 2 Gi0/2(static) Switch cust2 Vlan Ports ----- -----1 Gi0/3(static) 2 Gi0/3(static) Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show ip igmp snooping statistics vlan 1 Snooping Statistics for VLAN 1 General queries received : 0 Group specific queries received : 0 Group and source specific queries received : 0 ASM reports received : 477 SSM reports received : 0 IS_INCLUDE messages received : 0 IS_EXCLUDE messages received : 0 TO_INCLUDE messages received : 0 TO_EXCLUDE messages received : 0 ALLOW messages received : 0 Block messages rec
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 33 Static MAC Entries Command Static MAC Entries Command List mac-address-table aging-time mac-address-table static multicast mac-address-table static unicast show mac-address-table show mac-address-table aging-time show mac-address-table count show mac-address-table dynamic multicast show mac-address-table dynamic unicast show mac-address-table static multicast show mac-address-table static unica
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command mac-address-table static multicast vlan [recv-port ] interface ([ <0/a-b,0/c,...>] [ <0/a-b,0/c,...>] [port-channel ]]) [forbidden-ports ([ <0/a-b,0/c,...>] [ <0/a-b,0/c,...
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots mac-address-table static unicast To create a static unicast entry in L2 FBD. Command mac-address-table static unicast vlan [recv-port ] interface ([ <0/a-b,0/c,...>] [ <0/a-b,0/c,...
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots show mac-address-table To display the MAC address data learned or configured in MAC address table. Command show mac-address-table ] }] Syntax Description vlan vlan-range address aa:aa:aa:aa:aa:aa interface interface-type interface-id [vlan ] [address [{interface To display MAC addresses belong to a specific VLAN range.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command show mac-address-table aging-time Command Modes Privileged EXEC Mode Example switch# show mac-address-table aging-time Mac Address Aging Time: 300 Command History Version History 1.00.001 This command was introduced show mac-address-table count To display the statistics for each kind of MAC address in MAC address table.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description vlan vlan-range address aa:aa:aa:aa:aa:aa interface interface-type interface-id To display MAC addresses belong to a specific VLAN range. Specify a specific MAC address to display. To display MAC addresses under a specific port. Interface-type including Fa (Fast Ethernet), Gi (Gigabit Ethernet) or port-channel. Interface-id is slot/port number or port channel ID.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show mac-address-table dynamic unicast vlan 1 Vlan ---1 1 1 Mac Address ----------00:18:8b:bf:75:30 00:19:cb:d2:f2:75 00:22:15:0c:85:6c Type ---Learnt Learnt Learnt Ports ----Fa0/3 Fa0/11 Fa0/11 Total Mac Addresses displayed: 3 Command History Version History 1.00.001 This command was introduced show mac-address-table static multicast To display the static multicast MAC address in MAC address table.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced show mac-address-table static unicast To display the static unicast MAC address in MAC address table.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 34 Port Security Command Port Security Command List max learning address show max-learning-address max learning address To limits the number of MAC address learned from a port.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show max-learning-address Port ---Fa0/1 Fa0/2 Fa0/3 Fa0/4 Fa0/5 Fa0/6 Fa0/7 Fa0/8 Fa0/9 Fa0/10 Fa0/11 Fa0/12 Fa0/13 Fa0/14 Fa0/15 Fa0/16 Fa0/17 Fa0/18 Fa0/19 Fa0/20 Fa0/21 Fa0/22 Fa0/23 Fa0/24 Gi0/1 Gi0/2 Gi0/3 Gi0/4 Command History 34-2 Port Security Status Max Learning Address ---------------------------------Enabled 64 Disabled 0 Enabled 16 Disabled 0 Enabled 32 Disabled 0 Enabled 8 Disabled 0 Disabled 0
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 35 ACL Command ACL Command List mac access-list extended ip access-list deny (MAC Access List Configuration) permit (MAC Access List Configuration) deny (Standard IP Access List Configuration) permit (Standard IP Access List Configuration) deny (Extended IP Access List Configuration) permit (Extended IP Access List Configuration) deny icmp (Extended IP Access List Configuration) permit icmp
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command ip access-list { standard | extended } no ip access-list { standard | extended } Syntax Description standard access-list-number (1-1000) extended access-list-number (1001-65535) Specify the ID to a standard IP access control list. Specify the ID to a extended IP access control list.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description any Matching packets with any source MAC address. host mac-address any Matching packets with a specific source MAC address. host mac-address aarp Matching packets with a specific destination MAC address. amber Matching packets with ether type amber, 0x6008(24584). dec-spanning diagnostic Matching packets with ether type dec-spanning, 0x8138 (33080).
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots permit (MAC Access List Configuration) To configure a rule that packets matched will be processed.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command Modes MAC Access List Configuration Mode Example switch(config-ext-macl)# permit host 11-22-33-44-55-66 any msdos Command History Version History 1.00.001 This command was introduced deny (Standard IP Access List Configuration) To configure a rule that packets matched will be filtered.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description any Matching packet with any source IP address. host src-ip-address src-ip-address mask Matching packet with a specific source IP address. Matching packet with a range of source IP address. For example 172.17.5.1 with mask 255.255.255.0 means 172.15.5.0~255. Matching packet with any destination IP address.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description ip Matching all IP packets. ospf Matching all OSPF packets. pim Matching all PIM packets. protocol-type (1-255) any Matching packets with specific protocol type. host src-ip-address src-ip-address mask Matching packet with a specific source IP address. Matching packet with any source IP address. Matching packet with a range of source IP address. For example 172.17.5.1 with mask 255.255.255.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots permit (Extended IP Access List Configuration) To configure a rule that packets matched will be processed.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description ip Matching all IP packets. ospf Matching all OSPF packets. pim Matching all PIM packets. protocol-type (1-255) any Matching packets with specific protocol type. host src-ip-address src-ip-address mask Matching packet with a specific source IP address. Matching packet with any source IP address. Matching packet with a range of source IP address. For example 172.17.5.1 with mask 255.255.255.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots deny icmp (Extended IP Access List Configuration) To configure a rule that packets matched will be filtered. Command deny icmp {any |host | } {any | host | } {message-type <(0-255)>} {message-code <(0-255)>} Syntax Description any Matching packet with any source IP address.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description any Matching packet with any source IP address. host src-ip-address src-ip-address mask Matching packet with a specific source IP address. Matching packet with a range of source IP address. For example 172.17.5.1 with mask 255.255.255.0 means 172.15.5.0~255. Matching packet with any destination IP address.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots ip access-group To apply an IP access control list from the port. Command ip access-group no ip access-group [] Syntax Description access-list-number (1-65535) Command Modes Interface Configuration Mode User Guidelines Using no form to dissociate ACL from the port. Example switch(config-if)# ip access-group 1001 Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command History 35-13 Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 36 Classmap Command Classmap Command List class-map match access-group show class-map class-map To create or enter a class map. Command class-map no class-map Syntax Description class-map-number (1-65535) Command Modes Global Configuration Mode User Guidelines Using no form to delete a class map.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots User Guidelines The access control list rule must be created before associating. Example switch(config-cmap)# match access-group mac-access-list 1 Command History Version History 1.00.001 This command was introduced show class-map To display the settings of class maps.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 37 Policymap Command Policymap Command List policy-map class set police show policy-map policy-map To create or enter a policy map. Command policy-map no policy-map Syntax Description policy-map-number (1-65535) Command Modes Global Configuration Mode User Guidelines Using no form to delete a policy map.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots User Guidelines Class map must be created before associating. Example switch(config-pmap)# class 1 Existing Policy-map configurations have been deleted. Please apply the policy-map to make it active. switch(config-pmap-c)# Command History Version History 1.00.001 This command was introduced set To set the new 802.1p priority or DSCP type of packets match the associated ACL rule.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch(config-pmap-c)# police 64 exceed-action drop Command History Version History 1.00.001 This command was introduced show policy-map To display the settings of a policy map.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 38 Rate Limiting Command Rate Limiting Command List rate-limit egress rate-limit ingress show rate-limit rate-limit egress To enable and setup the egress packet rate limiting on a port.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command Modes Interface Configuration Mode User Guidelines The no form is to disable the rate limiting on a port. Example switch(config-if)# rate-limit ingress 64 Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 39 Storm Control Command Storm Control Command List storm-control pkt-type storm-control pkt-type To enable and configure the details of the storm control function. Command storm-control pkt-type { broadcast-only | multicast-broadcast | dlf-multicast-broadcast } rate-level no storm-control Syntax Description broadcast-only Only controls the broadcast packets.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 40 QoS Command QoS Command List set dscp vlan map-priority dscp map-type cosq scheduling algorithm switchport priority default show vlan traffic-classes show vlan port config show dscp show cosq algorithm set dscp To configure the priority and switch queue mapping Command set dscp { enable | disable } Syntax Description enable Enables DSCP and queue mapping.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description priority value(0-7) Specify which priority to map. traffic-class Traffic class value(0-3) Specify which switch queue to map. Default Settings Priority 0 1 2 3 4 5 6 7 Default traffic class 0 0 1 1 2 2 3 3 Command Modes Global Configuration Mode Example switch(config)# vlan map-priority 0 traffic-class 1 Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command cosq scheduling algorithm { strict | wrr } Syntax Description strict The traffic in highest queue always process first. wrr Using weighted round-robin algorithm to handle packets in priority queues. Default Settings Strict Command Modes Global Configuration Mode Example switch(config)# cosq scheduling algorithm wrr Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command Modes Privileged EXEC Mode Example switch# show vlan traffic-classes Traffic Class table --------------------Priority Traffic Class --------------------0 0 1 0 2 1 3 1 4 2 5 2 6 3 7 3 Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command History Version History 1.00.001 This command was introduced show dscp To display the current dscp setting. Command show dscp Command Modes Privileged EXEC Mode Example switch# show dscp DSCP is disabled Command History Version History 1.00.001 This command was introduced show cosq algorithm To display the current setting of CoS scheduling algorithm.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 41 RMON Command RMON Command List set rmon rmon alarm rmon event rmon collection history rmon collection stats show rmon set rmon To enable or disable RMON function. Command set rmon { enable | disable } Syntax Description enable Enable RMON. disable Disable RMON.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description number (1-65535) Specify the alarm number. mib-object-id (255) The MIB OID to set alarm. sample-interval-time (1-2147482647) absolute The time interval in seconds that alarm monitors the MIB variable. To test the MIB variable directly. delta To test the change between samples of a MIB variable. The threshold value to trigger alarm when the number of sample exceeds.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command Modes Global Configuration Mode User Guidelines 1. RMON function must be enabled and RMON event must be configured before configuring alarms. 2. Using no form to delete events from RMON event table. Example switch(config)# rmon event 1 description broadcast-too-high log owner trendnet trap redalert Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command rmon collection stats [owner ] no rmon collection stats Syntax Description index (1-65535) Specify the index of the RMON statistics collection. owner ownername (127) Specify the owner of the statistics Command Modes Interface Configuration Mode User Guidelines 1. RMON function must be enabled and RMON event must be configured before configuring alarms. 2.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show rmon RMON is enabled switch# show rmon statistics 1 alarms events history overview RMON is enabled Collection 1 on Fa0/5 is active, and owned by trendnet, Monitors ifEntry.1.5 which has Received 0 octets, 0 packets, 0 broadcast and 0 multicast packets, 0 undersized and 0 oversized packets, 0 fragments and 0 jabbers, 0 CRC alignment errors and 0 collisions.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 42 Statistics Command Statistics Command List clear interfaces show ip traffic clear interfaces To clear counters of interfaces. Command clear interfaces [ ] counters Syntax Description interface-type interface-id Command Modes Privileged EXEC Mode User Guidelines System will clear all interface counters when executing the command without a interface type and ID.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# show ip traffic IP Statistics: -------------Rcvd: 1817 total, 0 header error discards 0 bad ip address discards, 12 unsupported protocol discards Frags: 0 reassembled, 30 timeouts, 0 needs reassembly 0 fragmented, 0 couldn't fragment Bcast: Sent: 0 forwarded, 2845 generated requests Drop: ICMP Statistics: ---------------Rcvd: 4 total, 0 checksum errors, 0 unreachable, 0 redirects 0 time exceeded, 0 param probl
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 43 System Operation Command System Operation Command List watchdog copy ping help clear screen lock logout cmdbuffs show history dir flash: space flash: space memory: ? watchdog To auto-recover the Switch if Switch was found hanging up. Command watchdog { enable | disable} Syntax Description enable Enables the watchdog. disable Disables the watchdog.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command copy { tftp://ip-address/filename | flash: filename}{ tftp://ip-address/filename | flash: filename} Syntax Description tftp://ip-address/filename flash: filename tftp://ip-address/filename flash: filename The IP address the remote tftp server and the filename you would like to copy from. The path and filename of the local file you would like to copy from.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots help To list all the command starting with the given keyword and also display the description of the command. Command help Syntax Description command Command Modes All Modes User Guidelines System will display all commands under the command mode without descriptions when executing the command without a keyword. Example switch(config)# help sys Specify which command you would like to get the help.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example switch# clear screen Command History Version History 1.00.001 This command was introduced lock To lock the command line interface to prevent unauthorized user accessing the Switch. Command lock Command Modes Privileged EXEC Mode User Guidelines Entering the password of any privilege 15 user to unlock.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description user name Specify which user to configure the buffer size. no.of buffers (1-200) Specify the number of buffer size. Command Modes Global Configuration Model Example switch(config)# cmdbuffs root 200 Command History Version History 1.00.001 This command was introduced show history To display the command history had been executed.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command space flash: Command Modes Privileged EXEC Mode Example switch# space flash: Command History Version History 1.00.001 This command was introduced space memory: To display the space of DRAM remained Command space memory: Command Modes Privileged EXEC Mode Example switch# space memory: Command History Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Chapter 44 Interface Command Interface Command List interface shutdown mtu show interfaces show interface mtu show interfaces counters interface To create or enter a physical or logical network interface.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command shutdown no shutdown Default Settings Interfaces had been created are active by default. Command Modes Interface Configuration Mode User Guidelines The no form reactivates the interface. Example switch(config-if)# shut down Command History Version History 1.00.001 This command was introduced. mtu To setup the Maximum Transmission Unit (MTU) frame size of the interface.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Syntax Description interface-type interface-id Specify the information of which interface to display. Interface-type including Fa (Fast Ethernet) or Gi (Gigabit Ethernet). Interface-id is slot/port number.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Command show interface mtu [{ Vlan | port-channel | }] Syntax Description Vlan vlan-id (1-4094) port-channel port-channel-id (1-65535) interface-type interface-id VLAN ID Port channel ID Specify which interface to show the mtu setting. Interface-type including Fa (Fast Ethernet) or Gi (Gigabit Ethernet). Interface-id is slot/port number.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Example Command History 44-5 switch# show interface fa 0/12 counters Port InOctet InHCOctet -----------------Fa0/12 30159626 8763 30159626 InUcast InDiscard InErrs ------- --------- ------ Port OutOctet OutHCOctet -------------------Fa0/12 226671 2858 OutUcast OutDiscard OutErrs -------- ---------- ------- 0 0 0 Version History 1.00.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Technical Specifications Hardware Standards Interface Cabling Switching Method Protocol/Topology Buffer Memory Filtering Address Table Switch Fabric/Capacity LED Display Power Power Consumption Dimensions Weight Temperature Humidity Certifications Software Management Spanning Tree Link Aggregation Quality of Service 44-6 IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots VLAN IGMP Port Mirror Security Frame Size Bandwidth Control Flow Control Firmware Update 44-7 DSCP (Differentiated Services Code Point) Asymmetric VLAN 802.1Q Tagged VLAN & Dynamic GVRP Up to 256 static/dynamic groups Support IGMP Snooping v1/2 Up to 64 multicast entries RX, TX, or both MAC Address learning, ACL L2/L3/L4 User Authentication: 802.1X Port-Based Network Access Control, Local User Database 1522 bytes (max.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TL2-E284 – 3 Years Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots Go to http://www.trendnet.com/gpl or http://www.trendnet.com Download section and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. Please go to http://www.gnu.org/licenses/gpl.txt or http://www.gnu.org/licenses/lgpl.
24-Port 10/100Mbps Layer 2 Switch w/ 4 Gigabit Ports and 2 Shared Mini-GBIC Slots 44-10
