Quick Installation Guide TL2-E284 1.
Table of Contents English 1. Before You Start 2. Hardware Installation 3. LEDs 4. Configure the Switch 1 1 2 3 5 Troubleshooting 9 Version 11.23.
1. Before You Start Package Contents ŸTL2-E284 ŸMulti-Language Quick Installation Guide ŸCD-ROM (User's Guide) ŸRS-232 cable (3 m / 9.8 ft.) ŸPower Cord (1.8 m / 5.9 ft.) ŸRack Mount Kit Installation Requirements ŸWeb Browser: Internet Explorer (6.0 or higher) ŸA computer with a network adapter properly installed ŸCAT-5e or CAT-6 Network Cable ŸThe surface must support at least 2 Kg (4.4 lbs) for the Switch ŸThe power outlet should be within 1.8 meters (5.
2. Hardware Installation Note: Note: The Mini-GBIC slots are shared with port 25 and 26 Gigabit Ethernet ports. When the Mini-GBIC slots are in use, port 25 and 26 Gigabit Ethernet ports are disabled. 1. Connect the Power Cord to the TL2-E284 and then to a power outlet. 2. Connect a Cat.5e or Cat.6 RJ-45 network cable from the computer to an available Ethernet port on the TL2-E284. 3.
3.
Device Status LED PWR (Power) SYS (System) Ethernet LED (RJ-45) 100M Link/ACT 10M Link/ACT Combo Gigabit Ethernet (RJ-45) / Mini-GBIC LED 1000M Link/ACT 10/100M Link/ACT Color Sequence Definition Green Solid Device powered On N/A Off Device powered Off Green Solid Device is ready N/A Off Device is not ready Color Sequence Definition Solid 100/200Mbps (Half/Full Duplex) Connected (per port) Blinking 100/200Mbps (Half/Full Duplex) Data Transmitting/Receiving (per port) Green Amber
4. Configure the Switch Note: 1. Before the Switch can be configured, a Static IP address must be assigned to your computer's network adapter in the subnet of 192.168.10.x. Since the Switch's default IP address is 192.168.10.200, make sure no other network devices are assigned an IP address of 192.168.10.200. (Refer to Troubleshooting section on how to configure TCP/IP settings on your PC.) 2. There are three methods of configuring the TL2-E284: Web Browser, Console Port and Telnet. 1.
2. Using the Console Port Note: A terminal program such as HyperTerminal is required to configure the switch via the Console Port. The instructions shown below demonstrates how to configure the Switch on a Windows PC using HyperTerminal. 1. Connect the RS-232 cable from a serial port on your PC to the console port on the switch. 2. Go to Start Ž Programs Ž Accessories Ž Communications Ž HyperTerminal 3. Enter a name, choose an icon and then click OK. 4. Select the correct COM port (e.g.
5. Enter the following, click Apply and then click OK. Bits per second: 115200 Data bits: 8 Parity: None Stop bits: 1 Flow control: None 6. Press the Enter Key. 7. Enter the User Name for login. Then press the Enter. Then Enter the Password and then press Enter. By default login: admin Password: admin If you do not see the login prompt, please power cycle the switch by unplugging the power cord, wait 15 seconds and then plug it back in. 3.
2. Click Accessories and then click Command Prompt. 3. Type in telnet 192.168.10.200. Then press the Enter key. 4. Enter the User Name for login. Then press the Enter. Then Enter the Password and then press Enter. By default login : admin Password: admin If you do not see the login prompt, please power cycle the switch by unplugging the power cord, wait 15 seconds and then plug it back in.
Troubleshooting 1. How do I configure TCP/IP settings on my computer? Windows 7 1. Go into the Control Panel, click Network and Internet, click Network and Sharing Center, click Change Adapter Settings and then right-click the Local Area Connection icon and then click Properties. 2. Click Internet Protocol Version 4(TCP/IPv4) and then click Properties. Then click on Use the following IP address, and make sure you assign your network adapter an IP address in the subnet of 192.168.10.x. Windows Vista 1.
2. I typed http://192.168.10.200 in my Internet Browser's Address Bar, but an error message says “The page cannot be displayed.” How can I get into the TL2-E284's web configuration page? 1. Check your hardware settings again by following the instructions in section 2. 2. Make sure the PWR(Power), SYS(System) and Link/ACT lights are lit. 3. Make sure your network adapter’s TCP/IP settings are configured properly (see Q1). 4. Since the Switch's default IP address is 192.168.10.
11
TL2-E284 Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service. Specific warranty periods are listed on each of the respective product pages on the TRENDnet website. Garantie Limitée TRENDnet garantit ses produits contre les problèmes de matériel ou de fabrication, dans des conditions normales d'utilisation et de service. Les périodes de garanties précises sont mentionnées sur chacun des pages produits du site web de TRENDnet.
TL2-E284 Certifications This device can be expected to comply with Part 15 of the FCC Rules provided it is assembled in exact accordance with the instructions provided with this kit. Operation is subject to the following conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received including interference that may cause undesired operation. Waste electrical an electronic products must not be disposed of with household waste.
Copyright ©2010, All Rights Reserved. TRENDnet.