VDV & USB Cable Tester TC-NT3 TC-NT3(V1) /10.30.
Transmitter Network/Phone Port USB 2.0/3.0 Port LED Indicators Active Network Link LED Mode Selection Button Test Button Power On/Off Switch Remote Terminator USB 2.0/3.
Slide the bottom of the TC-NT3 Remote Terminator towards the back of the TC-NT3 Transmitter. Warning and Caution 1. This device is designed to be used on a cabling system without voltage. Do not connect the TC-NT3 to any live circuits, lines or outlets. Doing so may damage the TC-NT3 and equipment. 2. Disconnect cables from all electronic equipment with voltage before testing. Failure to do so may damage the TC-NT3. Install / Replace the Battery (9V Alkaline battery is not included) 1.
ENGLISH Network/Phone and USB Cable Test 1. Connect one end of a network, phone or USB cable to the Network / Phone (RJ45/12) or USB port on the Transmitter. Connect the other end of the network, phone or USB cable to the Remote Terminator. 2. Switch the power button to the On position; it will perform a Quick Test by default. Quick Test Mode Quick Test mode quickly identifies the type of cable.
Auto Scan mode is used to quickly test pin configurations. Step mode allows you to manually verify each pin one at a time. 1. Connect one end of a cable to the TC-NT3 Transmitter and the other end to the Remote Terminator. 2. Power on the TC-NT3 then press the Test button once. The AUTO/STEP LED will blink in to indicate Auto mode. The pin LEDs will indicate pin status. 3. To change to manual testing, press the Mode button once to enter Step mode. The Auto/Step LED becomes solid to indicate Step mode. 4.
ENGLISH Blink Hub/LINK/Tone Mode Blink Hub mode is a quick way to identify if a network cable or outlet is connected to an active network such as a hub, switch or router. Do not test a cable connected to a live telephone system or AC/DC circuits (PoE injector/switch) in this mode. Doing so will damage the TC-NT3. 1. Power on the TC-NT3. Press the Test button 2 times to go into Blink Hub mode. The Blink Hub LED will blink to indicate it is in Blink Hub mode. 2. Connect a cable to the TC-NT3 transmitter.
Quick Test Learn Mode Cable LED Indicator Transmitter: type B Transmitter: type A TX: 1 2 3 4 5 6 7 8 9 RX: 1 2 3 4 5 6 7 8 9 TX: 1 2 3 4 5 6 7 8 9 S RX: 1 2 3 4 5 6 7 8 9 S USB 3.0 USB 3.0 Transmitter: type A Transmitter: type A TX: 1 2 3 4 5 6 7 8 9 RX: 1 2 3 4 8 9 7 5 6 TX: 1 2 3 4 5 6 7 8 9 S RX: 1 2 3 4 8 9 7 5 6 S USB 3.0 TX: 1 2 3 4 RX: 1 2 3 4 TX: 1 2 3 4 S RX: 1 2 3 4 S USB 2.0 TX: 1 2 3 4 RX: 1 2 3 4 TX: 1 2 3 4 S RX: 1 2 3 4 S USB 2.0 Cable Type USB 3.0 USB 2.
Manufacturer’s Name and Address TRENDnet, Inc. 20675 Manhattan Place Torrance, CA 90501 USA Product Information: Model Number: TC-NT3 VDV & USB Cable Tester Product Name: TRENDnet Trade Name: TRENDnet hereby declare that the product is in compliance with the essential requirements and other relevant provisions under our sole responsibility.
Manufacturer’s Nom et Adre TRENDnet, Inc. 20675 Manhattan Place Torrance, CA 90501 USA Détails du produit: TC-NT3 Modèle: Nom du produit: Testeur de câbles USB et VDV Nom Commercial: TRENDnet TRENDnet déclare par la présente que le produit est conforme aux exigences essentielles et aux autres dispositions pertinantes de la Directive en vertu de notre seule responsabilité.
TC-NT3 Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following length of time from the date of purchase. Warranty: 1 year limited warranty (When Applicable: 1 year warranty for power adapter, power supply, and cooling fan components.) Visit TRENDnet.com to review the full warranty policy, rights, and restrictions for this product.
TC-NT3 Certifications This device can be expected to comply with Part 15 of the FCC Rules provided it is assembled in exact accordance with the instructions provided with this kit. Operation is subject to the following conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received including interference that may cause undesired operation. Waste electrical an electronic products must not be disposed of with household waste.
