Quick Installation Guide EL-HS800
1. How to Install 1. Rotate the EL-HS800's cover counter-clockwise to begin cable installation. 2. Remove the thumbscrew and protective plating from the goose neck wall mount. 3. Run all necessary cables (CAT 5 cable, Power Adapter cable, and the EL-HS800's power terminals) through the goose neck wall mount. When using a wireless camera, please run the Antenna cable also. 1 English Version 01.18.
4. Run each cable through the opening located at the top of the EL-HS800. DO NOT run all cables through the opening simultaneously. Serious blockage can occur. 5. After inserting the appropriate cables, extend each cable to 6 inches for camera installation. 6. Caution: Before cutting any power cord, make sure that the power cord is NOT PLUGGED into an electrical source. Now take a power cord with a two-prong plug and cut the wire.
7. Use a precision knife or a sharp object to split the wire in two halves. 8. Peel the plastic sheath to expose the copper wiring. It is recommended that you use a wire stripper to remove the plastic sheath effectively. 9. You should have two halves of exposed copper wire as shown below.
10. Pair one half of the power cable with the red terminal of the enclosure's power supply. 11. Place the yellow wire connector over the assembly in step 10, and twist the wire connector clockwise to secure the contact between the wired pair. 12. Repeat steps 10-11 for the next pair of terminals. 13. Pull in the power terminals into the goose neck wall mount.
14. Slide the protective plating into the goose neck wall mount and tighten the thumb screw. 15. Screw the goose neck wall mount on top of the EL-HS800 with an Alan wrench and three hexagon socket screws. 16. Take the circular base and connect three 2-inch Mounting screws and three nuts to create this assembly.
17. Mount the assembly in step 16 using three screws. 18. Take the assembly in step 18, and use three countersunk head screws to mount the assembly on top of the 2-inch mounting screws. 19. Take the TV-IP400/TV-IP400W and turn to the bottom of the camera. Remove the rubber molding to prepare the camera for the mounting. 20. Attach the mounting plate for the camera with a small screw.
21. Take the assembly in step 21 and mount the assembly on top of the mounting screws with regular screws. 22. Place the EL-HS800's cover over the camera and rotate the cover clock-wise.
Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase.
WARRANTIES EXCLUSIVE: IF THE TRENDnet PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT TRENDnet'S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local Authority or Retailer for recycling advice.
TRENDnet Technical Support US . Canada Toll Free Telephone: 1(866) 845-3673 24/7 Tech Support Europe (Germany . France . Italy . Spain . Switzerland . UK) Toll Free Telephone: +00800 60 76 76 67 English/Espanol - 24/7 Francais/Deutsch - 11am-8pm, Monday - Friday MET Worldwide Telephone: +(31) (0) 20 504 05 35 English/Espanol - 24/7 Francais/Deutsch - 11am-8pm, Monday - Friday MET Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.
