5AH28B User’s Guide Version 09.23.05 TRENDnet TRENDware, USA What's Next in Networking Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
Table of Contents English ...................................................................................................... 1 1. Prepare for Installation ...................................................................... 1 2. Install Hardware ................................................................................ 2 Troubleshooting ........................................................................................
English UG 1. Prepare for Installation Thank you for purchasing the TRENDnet 15AH28B Outdoor Internet Camera Server Housing with Fan/Heater. This guide will help you set-up your Outdoor Internet Camera Server Housing. Following the installations should be quick and easy. If you run into problems, please refer to the Troubleshooting section. If you need further technical support, please visit www.TRENDNET.com or call technical support by phone.
2. Install Hardware 1. Depress the levers to unlatch the roof of the camera enclosure, and pull the roof upward. 2. Unscrew the metal bracket from the camera enclosure. 3. Use the following screw to mount the metal bracket onto the base of the IP Camera.
4. Take the assembly in step 3, and mount the assembly inside the camera enclosure. 5. Caution: Before cutting any power cord, make sure that the power cord is NOT PLUGGED into an electrical source. Now take a power cord with a two-prong plug and cut the wire. 6. Use a precision knife or a sharp object to split the wire in two halves.
7. Peel the plastic sheath to expose the copper wiring. It is recommended that you use a wire stripper to remove the plastic sheath effectively. 8. You should have two halves of exposed copper wire as shown below. 9. Turn the camera enclosure upside down to remove one of the rubber stoppers. This will give you an opening for your power cord, antenna cable, or network patch cable.
10. Run your power cord, network patch cable or antenna cable through the opening of the camera enclosure. Note: For security purposes, attach the metal arm assembly to the camera enclosure and run the wires through the metal arm assembly. Please refer to the camera enclosure's attachment for setup details. 11. Pair one half of the power cable with the red terminal of the enclosure's power supply.
12. Place the yellow wire connector over the assembly in step 11, and twist the wire connector clockwise to secure the contact between the wired pair. 13. Pair the other half of the power cable with the black terminal of the enclosure's power supply. 14. Place the yellow wire connector over the assembly in step 13, and twist the wire connector clockwise to secure the contact between the wired pair.
15. Take the DC plug and connect the terminals into the DC box of the camera enclosure. 16. Turn the screw counter-clockwise to insert the DC Plug's terminal into the DC box. Insert one end of the DC plug terminal into the positive side of the DC box. Insert the other end of the DC plug terminal into the negative side of the DC box.
17. Secure the contact between the DC plug terminal and DC box by turning the screw clockwise. 18. Connect the DC plug with the IP Camera's power connector. 19. Make sure all internal wires are inside the camera enclosure, and carefully close the lid. Then plug in the two-prong cord into any power outlet. The camera's LEDs should immediately turn on. Your hardware installation is now complete.
Troubleshooting Q1. What do I do if the LEDs on my camera remain off? A1. Make sure that the power adapter is connected to a power outlet and that your power outlet is receiving power. Q2. My power outlet is receiving power, but my camera will not turn on. What do I do next? A2. Unplug the power cord from your power outlet, and open the camera enclosure. Double check your power supply's connections.
Limited Warranty TRENDware warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase.
WARRANTIES EXCLUSIVE: IF THE TRENDWARE PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT TRENDWARE'S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
TRENDnet TRENDware, USA What's Next in Networking @ Product Warranty Registration Please take a moment to register your product online. Go to TRENDware’s website at http://www.TRENDNET.com TRENDnet Technical Support US/Canada Support Center Contact Telephone: 1(310) 626-6252 1(310) 626-6267 Fax: Email: support@trendnet.
