Quick Installation Guide 15AH-28B
1. Before you start Package Contents 15AH-28B Quick Installation Guide Wall Mount Fasteners, washers and wall mount screws Installation Requirements The following items below are not included. Users must provide the items themselves. Make sure to have each item on hand before installation. Internet Camera Server (e.g.
2. Hardware Installation Note: Configure your Internet Camera Server to match your network settings before installing the device. 1. Lift up the latch and pull the roof upward. 2. Remove the metal bracket from the camera enclosure by unscrewing the four screws. Save these screws. You will need to use these screws later. 3. Use the following 2 sets of screws and washers to mount the metal bracket onto the base of the Internet Camera Server.
. Flip over the camera housing and remove the rubber stoppers and washers. 5. Remove the circuit board from the camera enclosure by unscrewing the two screws. Save these screws. You will need to use these screws later. 6. Take a power cord and cut it using a wire cutter. Cut it near the female end of the power cord. Note: The power cord is not included with 15AH-28B. 7. Cut the rubber insulation using a knife or box cutter.
8. Remove the insulation with pliers. 9. Run the power cord through the rubber stopper. 10. Insert the power cord through the hole and securely screw in the rubber stopper. 11. Insert the wires of the power cord into the power receptacle. Make sure the green and white wires match up. Make sure the black wires matches up with the orange wires. Then use a screwdriver to secure the wires.
12. Mount the Internet Camera Server inside the camera enclosure with the screws. Temporarily leave one hole unscrewed. This example shows a TRENDnet TV-IP100W. 13. Ground the green wire on the 15AH-28B. Then screw in the last hole. 14. Take the camera's power adapter and cut about 7 inches from the end the power connector using the wire cutter. Note: This is the AC/DC adapter that is included with your Internet Camera Server. 15. Take a knife or box cutter and cut along the middle to split the cable.
17. Run the power adapter and the RJ-45 Ethernet cable from the base to the top of the mounting arm. Make sure to leave one end of the RJ-45 Ethernet cable unterminated. 18. Insert the power adapter, RJ-45 Ethernet Cable through the rubber stopper screw it in securely. 19. Connect the two ends of the power adapter back by twisting the copper wiring. Make sure you do not cross the copper wires. 20. Use electrical tape to seal the cables back together.
21. Reconnect the circuit board back to the camera enclosure using the two screws. 22. Connect the Ethernet cable and power adapter to the camera. 23. Close and secure the back panel. 24. Plug the power cord and the camera power adapter into an available power outlet.
Mounting the Camera Housing 1. Place the mounting bracket against the wall and mark each of the four holes with a pencil. 2. Drill holes for the fastener plugs at each marked position. Make sure the drill bit matches the size of the provided white screw anchors. 3. Insert the fastener plugs into the holes.
4. Use the bracket screws to mount the mounting bracket to the housing. 5. Align the Wall Mount bracket with the fasteners, and then use the provided wood screws to secure it. Your installation is now complete.
Troubleshooting Q1: After I put my Internet Camera Server in the enclosure, the image is distorted. What should I do? A1: First, make sure that you have adjusted the focus on your camera. Second, mount the 15AH-28B so that it's not in direct view of the sun. Third, if you are using a day/night camera with auto iris lens, make sure to push the camera all the may to the front so that the lens is touching the glass. Q2: My Ethernet cable will not fit through the rubber stopper.
Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase.
WARRANTIES EXCLUSIVE: IF THE TRENDnet PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT TRENDnet'S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local Authority or Retailer for recycling advice.
TRENDnet Technical Support US . Canada Toll Free Telephone: 1(866) 845-3673 24/7 Tech Support Europe (Germany . France . Italy . Spain . Switzerland . UK) Toll Free Telephone: +00800 60 76 76 67 English/Espanol - 24/7 Francais/Deutsch - 11am-8pm, Monday - Friday MET Worldwide Telephone: +(31) (0) 20 504 05 35 English/Espanol - 24/7 Francais/Deutsch - 11am-8pm, Monday - Friday MET Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.
