a) b) c) d) e) f) a Wall Tile Shower Pan Liquid Membrane Crack Isolation Tape Concrete b d c f e fusion shower pan surface mounted on concrete installation guide www.TrendingAccessibility.
Installation Guide 2 for fusion shower pan surface mounted on conrete Required Components (included) b) c) f) e) d) a) b) c) d) e) f) Fusion Standard Shower Pan Tile Drain Liquid Waterproofing One Roll Rubberized Crack Isolation Tape 2 - Inside corners of Rubberized Crack Isolation Tape Gasket Membrane 15 - 2 1/2” screws 4 - 3/4” screws a) Required Tools (not included) • • • • • • • • • • • • • • • • • • www.trendingaccessibility.
Installation Guide 3 for fusion shower pan surface mounted on conrete Stainless Steel Grate Stainless Steel Grate Frame Height Extension Ring (5/8” - 1”) This must be fixed in place using solvent cement. Height Adjustment Ring (1/4” - 5/8” rotate counter-clockwise to increase height - This must be fixed in place using solvent cement. Gasket Clamp (use solvent cement on inner face to achieve seal) Gasket Membrane 3/4” Screws Drain Adapter Flange Fusion Pan Sealing Washers www.
Installation Guide 4 for fusion shower pan surface mounted on conrete Step 1 > > > > > > > > > For optimal performance, it is imperative there is a level surface prior to installation of new Fusion Pan. Check existing floor to make sure it is level. If it is not, please correct prior to installation. Place the Fusion pan in desired location and check to make sure it is level.
Installation Guide 5 for fusion shower pan surface mounted on conrete Step 5 > > > > > > > > > Install the drain in accordance with current plumbing and building codes. Step 6 > > > > > > > > > Set the Fusion pan into place and check to make sure the pan is level. This is important to achieve proper drainage. If you notice any rocking or flexing in the pan, you may need to shim or shave areas.
Installation Guide 6 for fusion shower pan surface mounted on conrete If required you may drill and countersink anywhere on the surface of the Fusion Pan. Step 9 > > > > > > > > > Again while insuring that your pan has remained level, drill and counter sink holes into the Fusion pan. Using cement anchors, attach the pan. Do not aggressively screw and over tighten, as you may force the Fusion Pan out of level.
Installation Guide 7 for fusion shower pan surface mounted on conrete Step 13 > > > > > > > > Make your final connections to the drain. First apply a bead of caulk to the underside of the strainer body. Pass the strainer through the drain adapter flange, and tighten. Make sure connection is snug but do not over tighten. Step 14 > > > > > > > > Materials needed for wet room waterproofing. You will now begin waterproofing the wet room.
Installation Guide 8 for fusion shower pan surface mounted on conrete Step 17 > > > > > > > > Just like you applied the corner pieces, use your cut strips of Crack Insulation Tape to cover all the seams. Again, trowel or paint liquid waterproofing onto seam, press tape into position and coat the top to seal. Make sure to fully cover both sides of the crack isolation tape with the liquid waterproofing product. To make this process more manageable, it is best to work in two foot sections.
Installation Guide 9 for fusion shower pan surface mounted on conrete Step 21 > > > > > > > > Begin the application of the liquid waterproofing membrane. Paint a layer of liquid waterproofing over all taped joints. It is easiest to begin with the walls first and then proceed to the floor area. For consistant application, use a paint roller to apply waterproofing to all surfaces. After first coat is dry, re-coat.
Installation Guide 10 for fusion shower pan surface mounted on conrete Step 24 > > > > > > > > The height adjustment ring and floor drain must now be fixed together using solvent cement. Because solvent cements sets very rapidly we strongly recommend the adjustment is done “dry” first. To set the permanent height of the grate frame, place a floor tile beside the frame. Rotate the frame until the height is about 1/16” higher (this accounts for adhesive thickness).
