a) b) c) d) e) f) g) h) a Wall Tile Adjustable Shower Pan Liquid Membrane Crack Isolation Tape Cement Board Subfloor Joists b d c f g h e adjustable fusion shower pan surface mounted on subfloor installation guide www.TrendingAccessibility.
Installation Guide 2 for adjustable fusion shower pan surface mounted on subfloors Required Components b) c) f) e) d) a) b) c) d) e) f) Adjustable Fusion Shower Pan Tile Drain Liquid Waterproofing One Roll Rubberized Crack Isolation Tape 2 - Inside corners of Rubberized Crack Isolation Tape Gasket Membrane 15 - 2 1/2” screws 4 - 3/4” screws a) nt stme Adju 0° 36 Important: Do not install this kit without the appropriate waterproof‐membrane liners or coating.
Installation Guide 3 for adjustable fusion shower pan surface mounted on subfloors Stainless Steel Grate Stainless Steel Drain Frame Height Extension Ring (5/8” - 1”) (Optional) - This must be fixed in place using solvent cement. Height Adjustment Ring (1/4” - 5/8” rotate counter-clockwise to increase height - This must be fixed in place using solvent cement.
Installation Guide 4 for adjustable fusion shower pan surface mounted on subfloors Step 1 > > > > > > > > > For optimal performance, it is imperative there is a level surface prior to installation of new Adjustable Pan. Check existing floor to make sure it is level. If it is not, please correct prior to installation. Place the Adjustable pan in desired location and check to make sure it is level.
Installation Guide 5 for adjustable fusion shower pan surface mounted on subfloors Step 5 > > > > > > > > > If the drain position lands over a joist, Simply rotate the plate until free of obstacles. Step 6 > > > > > > > > > Once plate is set in the desired location, mark the orientation on the plate and the pan. This will ensure that you have the plate properly aligned when you go to reinstall it later.
Installation Guide 6 for adjustable fusion shower pan surface mounted on subfloors Step 9 > > > > > > > > > To prep for permanent installation, remove the Adjustable Fusion pan from the surface. Apply a generous amount of construction adhesive to the subfloor. Step 10 > > > > > > > > Carefully set the Adjustable pan into place. Drill and countersink holes in the pan. Using the 2 ½” screws provided, attach the pan.
Installation Guide 7 for adjustable fusion shower pan surface mounted on subfloors Step 13 > > > > > > > > Check that the Fusion Pan is level on all four sides. Fill in any gaps around the perimeter of the pan over 1/8” with latex or acrylic caulk. Do not use 100% silicone. Step 14 > > > > > > > > Make your final connections to the drain. First apply a bead of caulk to the underside of the strainer body. Pass the strainer through the drain adapter flange, and tighten.
Installation Guide 8 for adjustable fusion shower pan surface mounted on subfloors Step 17 > > > > > > > > Using the 5” crack isolation tape provided, cut strips of tape to length, to cover all seams (Corner seams, wall/floor seams, pan/floor joint). Put pieces aside. If you are creating full wet room, you will need to tape any seams throughout the entire room. If you are only waterproofing the shower zone, you will only need to tape the seams up to 2 feet outside the shower area.
Installation Guide 9 for adjustable fusion shower pan surface mounted on subfloors Step 21 > > > > > > > > Gasket Clamp Now attach the clamping ring. Apply solvent cement to inside of clamping ring. Press firmly into position and allow the solvent to set. NOTE: Do not allow the solvent cement to come into contact with the membrane Drain Adapter Flange Gasket Membrane Step 22 > > > > > > > > Begin the application of the liquid waterproofing membrane.
Installation Guide 10 for adjustable fusion shower pan surface mounted on subfloors Step 24 > > > > > > > > In order to set the correct height of the grate frame, you may need to use the height extension ring (see diagram to the right). If the height extension ring is required, it will need to be fixed to the height adjustment ring using solvent cement. The grate frame can now be attached to the height adjustment or extension ring, depending on tile thickness.
Installation Guide 11 for adjustable fusion shower pan surface mounted on subfloors Step 27 > > > > > > > > Once your tiling is complete, grout the floors and walls. Finalize by adding the drain grate. Your Fusion Pan installation is now complete.
Installation Guide 12 for adjustable fusion shower pan surface mounted on subfloors Adjustable Fusion Shower Pan - Cutting and Drilling guideline Cutting and Drilling Guidlines Do not cut into central solid oval section Maxim um cut Maxim um cut Maxim um cut Maxim um cut Fig.1 Cut using an old or disposable handsaw. Additional timber F ig . 2 Cu t t o l e n g t h . Additional timber Additional timber F ig . 3 C u t t o a c c o m m o d a t e d ia g o n a l w a ll . Fig.
