Instruction Manual

7
NETB/LINC Installation Instructions TG200632 Issue 1/C 15/11/06
Installation Instructions NETB/LINC
16
Note Neuron ID
addRess/ neuron chip id 00:00:00:00:00:00
17
Exit Configuration
X
Æ "Exit from Utility"
3.2 Installation - Configuration (Continued)
14
Set up following parameters
Note that a PIN may be required to make changes in configuration mode. If the PIN has been forgotton the users should contact their supplier (installers contact Technical
Support) quoting the generator number (User module) and neuron id (Address module) whereupon a default PIN will be supplied. This will only work during the same
configuration mode session i.e. the utility must not be exited between reading the generator and entering the default PIN. After the PIN is entered a new PIN should be set up
and remembered.
edamebtsumtahtsgnitteS
retemaraPgnitteSnoitcnuFnoitidnoC
sserddAPratnoitulosersserddA
seY=tluafed,locotorp
lab
olgfforonosehctiwS
segassemnoitulosersserdda
sselnuoNotegnahC*
CNILdnocesotdetcennoc
noLyb
lacol
smrala
rddAs
serddaedonmralaCNILfosserddaedon
tegrat
pooltnerrucdnesot
smralakrowten
naletomeRrebmunnaLmralaCNILforebmunn
aL
tegrat
pooltnerrucdnesot
smralakrowten
ten/tni
smrala
EdonsserddaedonmralaCNILfosserddaedon
tegrat
noLmorfsm
raladnesot
krowtenretni
naleTomerrebmunnaLmralaCNILforebmunnaL
tegrat
noLmorfsmraladnesot
krowtenretni
* Note that to speed up
communications,TARP should
be changed to No unless there
is more than one LINC physically
connected by LonWorks.
Installation on a LonWorks
Management Tool sets TARP to
Yes and it can no longer be
changed in configuration mode
(see step 18).
Note
1: If PIN is forgotton see note in step 14
2: Message code can only be changed in configuration mode if 'lonworks managed' is set to No (i.e. managed by LINC). If
the LINC is installed on LonWorks Management Tool (see step 19 ), 'lonworks managed' is set to YES, and Message code
cannot be changed in configuration mode.
15
Optional Settings
Set up the following parameters if required. The table shows setting that may be required for special circumstances
edamebyamtahtsgnitteS
retemaraPgnitteSnoitcnuFnoitidnoCetoNeeS
resUniPrebmunnisegnahcstcetorP
edomnoitarugifnoc
.)detcetorpnu(knalbsitluafeD
.deriuqerytirucesfiputeS
1
sserddAreifitneDIciremunahpla51
ton-sretcarahc
sretc
arahc*?;{(^
sihtrofreifitnedi
CNIL
yalpsid,srosivrepusrofputeS
slenap
skrownoledocegasseM.rebmunedoc
.46=tlua
feD
llA
sLQI/sCNOL/sCNIL
edocemasesutsum
desugniebedocegassemfI
ebtsum-sresurehtoyb
metsysQIotevisulcxe
2
ezi
sreffuBretuor)setyb(ezisreffub
641=tluafeD
tsellamsseificeps
noreffubretuor
metsys
dnasCNILetarapessretuorfI
nahtrellamsezisreffubevah
tsellamsottes-setyb641
)66=muminim(.ezisreffub
reViecsnartsenifedrebmun
epytrev
iecsnart
)01-TTF(0=tluafeD
0MORFEGNAHCTONOD
emityrter-r skroWnoLmetsysQIeeS
ediuGgnireenignEstcudorP
sliate
drof
tekcapretni-i
yaled
ssalcecivres-s
SCN
SCN
T-
T+
R-
R+
T-
T+
R-
R+
N
E
L
~
230 Vac
This unit must be earthed
LON
J18
J8
J4
J14
J7
J6
J16
SERVICE
1 2 4 8
16 32 64
19k2
9K6 1K2
BAUD
ADDRESS
S3
FSI
J1
J5
TX
RX
LonA
LonB
SCN
LonA
LonB
SCN
LON OK
LAN OK
D2
D3
TREND NETWORK
a). When installing LINC On
LonWorks tool enter
neuron ID from step 16 - or
press service button.
18
Install on LonWorks Network Management Tool (LMT)
service button
If a binding IQLs to LonMark Devices
or b LINCs version <3.23 straddle router
or c other devices have address conflicts with IQ system devices
or d LONROUTERS used on system already installed on LMT
If one IQ system Lon device is installed on LMT, all must be installed
b). The LINC network image can be retrieved by uploading
the XIF file from LINC to tool.
See LonWorks network management
tool manual. See IQ system LonWorks
Products Engineering Guide
(TE200292). Lonworks System
Integrator must have Lonworks
engineering expertise.
Note that if a 3xtend/EINC L is installed in the LonWorks segment, IQ system devices cannot be installed on a LMT
because 3xtend/EINC L does not support installation on a LMT.