Installation Instructions NBOX(B)TMNE, G, H Trend Modem Node Controller Important: Retain these instructions CONTENTS 1.1 Unpacking 1.2 Storing 1.3 Installation - Mounting 1.4 Installation - Configuration 1 1 1 5 2 Limitations of Use 3 Resetting the Node 4 Disposal 14 16 16 1 Installation Instructions 1.1 Unpacking EJ 10 53 83 ../24 only ../230 only TMNH only 1.2 Storing +50 °C (122 °F) -10 °C (14 °F) H2 O ..
NBOX(B)TMNE, G, H Installation Instructions 1.3 Installation - Mounting (continued) Requirements 2 b a c d +45 °C (113 °F) 0 °C (32 °F) T M N TMNE 0 %RH T M N H2 O T M N 90 %RH TMNH, TMNG 90 %RH 20 %RH Protection :IP30 (NEMA 2) e f TMNG only 1 >=20 cm (8") 2 3 TMNG only Mount antenna away from souces of interference (e.g. domestic appliances, computer monitors or TV receivers, machinery with high HF leakage) Do not operate near unshielded or susceptible equipment (e.g.
Installation Instructions NBOX(B)TMNE, G, H 1.3 Installation - Mounting (continued) NBOX(B)/TMN Consumption < = 7.5 VA /230 230 Vac 2 3 0 V either screw terminal E N L ~ Connecting Input Power Supply /230 version 2 4 V ~ 6 R D S /R S 2 3 2 M O D E M ! a Terminal size 0.5 to 2.
NBOX(B)TMNE, G, H Installation Instructions 1.3 Installation - Mounting (continued) 8 Connect Network (unless direct connected to single device - old IQs or configuration) polarity independent 19k2 38k4 No.
Installation Instructions NBOX(B)TMNE, G, H 1.4 Installation - Configuration 1 2 Switch off Open MBOX 3 if unit fitted in ENCLS/MBOX/IQ22x Open Flap a O I 4 b Set the Network Baud Rate (or Device A RS232 baud rate if connected to single device) BAUD A BAUD B BAUD A e.
NBOX(B)TMNE, G, H Installation Instructions 1.4 Installation - Configuration (continued) 6 Set Dumb/Normal switch D U M B e.g. Dumb only for pre Network+ (pre 1985) O N N O R M Normal for all other networks A D D R E S S 7 Set modem/terminal adaptor baud rate BAUD B BAUD B BAUD A set baud rate to maximum baud rate of modem or terminal adaptor up to 19k2. e.
Installation Instructions NBOX(B)TMNE, G, H 1.4 Installation - Configuration (continued) 10 1 2 3 4 5 Plug in SIM Card (TMNG only) Contact a GSM service provider. (In UK Trend recommend O2 or Orange.) Obtain a GSM data enabled SIM card with a data number (9600 bps) in addition to the normal voice number. (For O2 or Orange stress Mobile Terminator Data SIM required; if O2 also stress analog data number required.) Communications with an /ADL require the SIM card to have a 2400 bps data number.
NBOX(B)TMNE, G, H Installation Instructions 1.4 Installation - Configuration (continued) Check Network 16 a RX (yellow) NBOX(B)/TMN Not if local device connector plugged into Dev A (1.4 step 9) ? b TX (yellow) NBOX(B)/TMN ? c OK (green) Network Address Invalid 0,2,3 or >119 OK NBOX(B)/TMN L A N T X - T X + A R X - Check network cabling for short circuits with a multimeter (NOT Megger) OK TMN Faulty R X + L A N A Check baud rate .
Installation Instructions NBOX(B)TMNE, G, H 1.4 Installation - Configuration (continued) 19 Check Settings - Default Leave the following TMN default configuration settings unchanged for normal operation.
NBOX(B)TMNE, G, H Installation Instructions 1.4 Installation - Configuration (continued) 21 Settings for special conditions Set up following parameters if special conditions apply.
Installation Instructions NBOX(B)TMNE, G, H 1.4 Installation - Configuration (continued) 22 Configure GSM modem settings As a result of inserting the SIM card (1.4 step 10), select ‘init’ from top level config prompts (see 1.4 step 18) to automatically re-initialize modem (v4.5 and greater only). For TMNG v4.4 the settings must be entered manually: • In configuration mode with the top menu prompts displayed, type 'direct'.
NBOX(B)TMNE, G, H Installation Instructions 1.4 Installation - Configuration (continued) 24 Set up device (communicating by way of TMN) (continued) TMN 915MDS, 916MDS TMN using SANC - no need for TMN 915, 916 Lan I/N 915, 916 direct • Put outstation address, Lan, and phone number in TMN record. • If dialling a TMNG, use its data number modem • Can only dial into TMN, TMN cannot dial into 915 + modem. Dialling into TMN v4.1 needs manual addressing in 915, TMN >= v4.
Installation Instructions NBOX(B)TMNE, G, H 1.4 Installation - Configuration (continued) 28 Install auto-dialled end Device Install A/D TMN When MNC dials into TMN it must have telephone number prefixed with SW. TMNE may not be able to communicate with MNC if its modem cannot achieve V21. TMN cannot dial into 915 + modem but 915 + modem can dial into TMN >= v4. TMN must be >= v4.
NBOX(B)TMNE, G, H Installation Instructions 1.4 Installation - Configuration (continued) 30 Close MBOX if fitted in ENCLS/MBOX/IQ22x a b 2 Limitations of Use 2.1 TMNH INTEGRAL MODEM (MT5600SMI-92) 2.1.1 Approvals The CE and UL Approvals are defined in the Specification (Environmental) section of the TMNE, G, H data sheet (TA200734). 2.1.2 General Host Equipment: The TMNH consists of the TMN host with the attached modem daughter board.
Installation Instructions NBOX(B)TMNE, G, H 2 Limitations of Use (continued) “This product meets the applicable Industry Canada technical specifications” The REN is 0.1B REN: For Canada the sum of the RENs of all the devices must not exceed five”. Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Reglement Canadien sur le matériel brouilleur.
NBOX(B)TMNE, G, H Installation Instructions 3 Resetting the Node Open MBOX 1 a Open Flap 2 if unit fitted in ENCLS/MBOX/IQ22x b Check Network Address and Dumb/Normal Switch 3 4 Set all Poles to Zero D U M B 6 4 3 2 8 1 6 4 2 1 O N N O R M A D D R E S S D U M B O N Address = 2 + 16 = 18 DUMB D U M B N O R M NOT SET SET O N A D D R E S S NORMAL N O R M A D D R E S S 5 Wait 3 Seconds 6 OK Set Network Address, Dumb/Normal Swtich section 1.
