Manual

ManualsBrandsTREND ManualsAccessories for electricalKIT_NODE_IQ25x

KIT/NODE/IQ25x Installation Instructions TG200595 Issue 1/B 21/11/06

Important: Retain these instructions

Installation Instructions

KIT/NODE/IQ25x

Node Mounting Kit

Switch Off

Isolate I/O

WARNING: The connecting leads may

be connected to input power.

Isolate before touching.

Open Panel

WARNING: Opening the panel may expose

dangerous voltages.

417-IEC-5036

1 UNPACKING

KIT/NODE/IQ25x

Installation

Instructions,

TG200595

CABLE/EJ102364

POWER

25 W Male

red

sheath

25 W

Female

black

sheath

CABLE/EJ103817

RS232/TMNE

CABLE/EJ100179A001

RS232/CNC2, PNC2

MolexMolex

2 INSTALLING A NODE IN IQ250/251 USING KIT/NODE/IQ25X

78-2781

NETWORK

IQ251/USA

The unit is UL rated as

'UL916, listed open energy

management equipment'

Unscrew Main Cover

Remove 6 screws

CAUTION: This unit contains static sensitive devices. Suitable anti-static

precautions should be taken throughout this operation to

prevent damage to the unit. BS EN100115/1 Basic

Specification: protection of electrostatic sensitive devices.

Unscrew Main Cover

Remove Network Links

J 1 2 M N C

J 1 3

J 1 2 M N C

J 1 3

Pull off links

Store Cover on Back of Unit

Not ANC, AND, MNC, TMN if on internetwork.

Not INC2 if used as internetwork repeater

(dumb/normal = normal, address>=100)

AD DR ES S

EJ104091

EARTH

(GROUND)

Summary of content (8 pages)

PAGE 1
Installation Instructions KIT/NODE/IQ25x Node Mounting Kit Important: Retain these instructions 1 UNPACKING 78-2781 NETWORK EJ104091 EARTH (GROUND) CABLE/EJ102364 POWER 2 25 W Female 25 W Male red sheath black sheath Molex Molex CABLE/EJ103817 RS232/TMNE KIT/NODE/IQ25x Installation Instructions, TG200595 CABLE/EJ100179A001 RS232/CNC2, PNC2 INSTALLING A NODE IN IQ250/251 USING KIT/NODE/IQ25X 1 Switch Off 2 Isolate I/O 3 Open Panel IQ251/USA The unit is UL rated as 'UL916, listed open e
PAGE 2
KIT/NODE/IQ25x 2 Installation Instructions INSTALLING A NODE IN IQ250/251 USING KIT/NODE/IQ25X Connect Local Network Cable 8 Install Nylon Inserts 4 off Not ANC, AND, MNC, TMN if on internetwork. Cable 78-2781 supplied Nylon insert Not INC2 if used as internetwork repeater (dumb/normal = normal, address >= 100).
PAGE 3
Installation Instructions 2 KIT/NODE/IQ25x INSTALLING A NODE IN IQ250/251 USING KIT/NODE/IQ25X Connect Input Power Cable to IQ25x 16 17 Cable EJ102364 supplied Connect Local Network to Node Board (4 wide) Not ANC, AND, MNC, TMN if on internetwork Not INC2 if used as internetwork repeater (dumb/normal = normal, address >=100).
PAGE 4
KIT/NODE/IQ25x 2 Installation Instructions INSTALLING A NODE IN IQ250/251 USING KIT/NODE/IQ25X 20 (Continued) Connect Internetwork and Internetwork Segment B to Node Board Internetwork for INC, INC2 Internetwork Segment B for INC2 if used as internetwork repeater (dumb/normal = normal, address >=100) (a) either pierce grommet (b) or use copex gland Connect internetwork J 8 (c) Internetwork cable T + Lan B R + L a n B R - J 9 (Lan B) Internetwork Internetwork Segment B if INC2 used as int
PAGE 5
Installation Instructions 2 KIT/NODE/IQ25x INSTALLING A NODE IN IQ250/251 USING KIT/NODE/IQ25X 22 (Continued) Connect Device to IQ25x RS232/Modem Connector CNC2 PNC2 TMNE Modem/ Terminal Adaptor 25 Way D type Male 25 Way D type Male 9 Way D type Female CABLE/58-0750 25 Way D type Male Special cable, pins 3,7,20 connected straight through Standard 24 way cable wired 1 to 1 through to 25 to 25 25 Way D type Male 25 Way D type Female Route Special Device Cables For ENC, MNC, TMNH J 8 23 (b) Id
PAGE 6
KIT/NODE/IQ25x 2 Installation Instructions INSTALLING A NODE IN IQ250/251 USING KIT/NODE/IQ25X 24 Link Network Connectors (Continued) If ANC, AND, XN28, MNC, TMN, is fitted and IQ25x is not networked (stand alone) N E T W O R K O U T IN T X R X O N T - A D D R E S S 25 Connect to LonWorks (b) For LINC only T + R - R + T - T + R - R + Route cables through hole either pierce grommet (a) Knock out hole or use copex gland (c) Connect Lon cables 9 1 0 P O W E R J 1 L A N J 1 5 2
PAGE 7
Installation Instructions 2 KIT/NODE/IQ25x INSTALLING A NODE IN IQ250/251 USING KIT/NODE/IQ25X (Continued) Check Trend Lan and Internetwork sections 29 Do separate check for each Lan/Internetwork segment IQ 2 3 x TMN type board shown Check node data sheet for location of LEDs on other boards a J 8 RX (yellow) ? IQ 2 3 x b TX (yellow) J 9 ? L a n B E T 1 J 7 J 1 6 D e v A D e v B M o d e m J 1 5 L a n A c OK (green) Network Address Invalid 0, 2, 3 or >119 LAN N E T W O R K O U T IN
PAGE 8
KIT/NODE/IQ25x 2 Installation Instructions INSTALLING A NODE IN IQ250/251 USING KIT/NODE/IQ25X 34 Reconnect Input Power to I/O 35 (Continued) Configure If required (INC, INC2, ANC, AND, XN28, MNC, TMN, ENC, XNC+, LINC) Node Installation Instructions O I 36 Test System Node Installation Instructions 3 DISPOSAL WEEE Directive : At the end of their useful life the packaging , product, and batteries should be disposed of by a suitable recycling centre.