Manual

KIT/NODE/IQ23x Installation Instructions - Part 1
KIT/NODE/IQ23x Node Fixing Kit Installation Instructions TG200570 Issue 1/A 31/5/02
1 - 2
~
0 V
~
J 5
J 2
J 1
R S 2 3 2 A
P O W E R
1.1 Installing a Node in IQ23x using KIT/NODE/IQ23x - Part 1 (continued)
Screw on Plate
8
R X
T X
O K
1 2 8 4 16 32 64 1K 2 9K 6 19 K 2
A D D R E S S
B A U D
R X
T X
O K
1 2 8 4 1 6 3 2 6 4 1 K 2
9 K 6
1 9 K 2
A D D R E S S
B A U D
Fix Node to Plate
10
Connect Earth Cable
to IQ23x
11
J 5
J 2
J 1
R S 2 3 2 A
P O W E R
J 7
E T 1
J 1 6
D e v B
J 1 5
D e v A
J 9J 8
L a n B L a n A
M o d e m
Pre-TMN type boards
TMN type boards
power connector top left
hand corner
power connector top right
hand corner
Connect Earth to Node Board
12
J 7
E T 1
J 1 6
D e v B
J 1 5
D e v A
J 9J 8
L a n B L a n A
M o d e m
Pre-TMN type boards
TMN type boards
Connect Power
Cable to IQ23x
14
R X
T X
O K
1 2 8 4 1 6 3 2 6 4 1 K2 9 K6 1 9K 2
A D D R E S S
B A U D
J 5
J 2
J 1
R S 2 3 2 A
P O W E R
J 7
E T 1
J 1 6
D e v B
J 1 5
D e v A
J 9J 8
L a n B L a n A
M o d e m
Pre-TMN type boards
TMN type boards
J2
CABLE/EJ103087 supplied
polarised connector
~
~
O
+
-
J2
POWER
Connect Local Network to Node Board (4 wide)
15
J 5
J 2
J 1
R S 2 3 2 A
P O W E R
T -
R -
R +
T +
J 7
J 3
J 2
L A N
P O W E R
J 5
J 2
J 3
J 4
J 1
L a n BL a n A
R S 2 3 2 A R S 2 3 2 B
P O W E R
J 4
J 1 2
J 1 3
J 3
J 2
L a n BL a n A
R S 2 3 2 B
R S 2 3 2 A
P O W E R
CNC, PNC (circa 1988)
CNC, PNC (circa 1997)
INC, ANC, ENC, XN28,
XNC+ (circa 1988)
INC, ANC, AND, ENC,
XN28 (circa 1997)
local network (J5)
local network (LAN)
local network (Lan A) local network (Lan A)
(ENC only)
(ENC only)
Lan A
Place Node on Plate
9
Ensure correct orientation of node board
CABLE/EJ103087
supplied
CABLE/EJ103087
supplied
Connect Power Cable to Node Board
13
EJ101835
supplied
EJ101835
supplied
DO NOT
SWITCH ON
O
1
Note: ANC, AND, MNC, TMN if on internetwork
Note: INC2 if used as internetwork repeater (dumb/normal = normal,
address >=100). For LINC see step 17
CABLE/EJ103086
supplied
3 screws supplied
4 screws supplied
Ensure socket is connected to correct terminal pins (+, -, or , 0V)