Product Manual

ManualsBrandsTraxion ManualsAutomotiveFoldable Topside Mechanic's Creeper — 400-Lb. Capacity

engineered products

OWNER’S MANUAL

Foldable Topside Creeper

Model 3-100

Please read and understand all safety advisories and

operating instruction in this manual to ensure safe and

productive operation of your new Topside Creeper.

If you have any questions please contact us at:

phone: 479-474-3460

email: service@traxionproducts.com

VIDEO INSTRUCTIONS ARE AVAILABLE ON

OUR WEBSITE AT:

www.traxionproducts.com

Safety First

WARNING: Failure to follow these safety requirements could result in personal injury.

This product is a tool to reach what are normally hard to reach places, such as the topside of an

engine compartment for mechanics.

Always inspect the product for damage before each use. Do not use if damage is detected. Make

sure all nuts and bolts are secure before each use.

Always engage the caster locks before using the Topside Creeper.

Always make sure the angle adjustment bar is secure in one of the three position slots before using.

Always face the Topside Creeper when climbing up or down. Use both hands and keep your body

centered between the rails.

DO NOT USE THE PRODUCT if you tire easily or are subject to fainting spells or disorientation.

DO NOT USE THE PRODUCT if you are taking medication that could impair judgement.

DO NOT USE THE PRODUCT if you are under the influence of drugs or alcohol.

DO NOT USE THE PRODUCT if you are physically challenged.

DO NOT sit or stand on the chest pad.

DO NOT overload the product. The maximum capacity is 400 lbs (180 kg) which includes body

weight, tools and torque applied to tools.

DO NOT use the Topside Creeper over a running engine.

Summary of content (7 pages)

PAGE 1
OWNER’S MANUAL engineered products Foldable Topside Creeper Model 3-100 Please read and understand all safety advisories and operating instruction in this manual to ensure safe and productive operation of your new Topside Creeper. If you have any questions please contact us at: phone: 479-474-3460 email: service@traxionproducts.com VIDEO INSTRUCTIONS ARE AVAILABLE ON OUR WEBSITE AT: www.traxionproducts.
PAGE 2
Parts List Tools Needed 12mm wrench 8mm socket 6mm wrench philips screwdriver
PAGE 3
Assemble Base NOTE Assemble legs (M1 and M2) to Base (N) using bolts (F), Nuts (C) and Pins (I) as shown. Do not overtighten. The two legs must be angled outward with angle adjustment notches on the inside. Attach Casters With angle adjustment notches upward, secure two Locking Casters (A2) to closed end of the base (N) using Flange Nut (B). Secure two non-locking casters (A1) to the outward protruding legs using Flange Nuts (B) as shown. Attach Climbing Section Position step section (O) as shown.
PAGE 4
Attach Angle Adjust Keepers Place angle adjustment bar into one of the three adjustment slots located on the base. Secure Angle Adjustment Keepers (N) to base using Bolts (G3) and Lock Nuts (E). Attach Base Cross Bar Using two Bolts (G1), two Nuts (D) and Washers (Q), attach Square Tube Cross Bar Support (J) to base as shown. Attach Padded Deck Frame Using Bolts (G2) and Nuts (D) secure chest frame to climbing section as shown.
PAGE 5
Attach Tool Pouch Insert Philips Head Screws (H) through Bracket (S), Pouch (R) and Padded Deck Frame as shown. Secure to frame using Lock Nuts (E). Attach Padded Deck Using two Philips Head Screws (H) secure the padded deck to the frame. Insert screws through holes in the bottom of the frame and into the threaded inserts in the bottom of the pad. Attach Bumper Pads Slide the three Bumper Pads (U) onto the angle support bars and the crossbar with the spring-loaded pins.
PAGE 6
Operating Instructions Using the adjustable angle lean-in feature There are three different lean-in angles that allow the user to adjust positioning. This helps the user to maximize safety and productivity. To adjust angle lean-in: 1. Lock casters (A2) by pressing the lock tab with your foot on each of the locking casters. 2. Push back on the climbing section (O). 3. Move angle adjustment to one of the three notches located on the base.
PAGE 7
Other Stuff From TraXion Engineered Products... Thank you for purchasing the Topside Creeper from TraXion Engineered Products. If you need anything please call us at 800-364-7359 or email service@traxionproducts.com. There is more information, including assembly videos on our website at: www.traxionproducts.