Submittal Sheet

6/19

Thermaco, Inc. • PO Box 2548 • Asheboro, NC 27204-2548 • (336) 629-4651 • www.trapzilla.com

Trapzilla

Grease Interceptor

TZ-1826-ECA Specications

NOTES

1. READ instruction manual included with system before installing/operating.

2. Unit requires 6” (15.24 cm) of clearance all the way around the lid from walls or other structures to allow for servicing.

3. Make piping connections with rubber “No Hub” connectors.

4. Keep outlet piping as straight as possible. Use only “sweep” connections.

5. Install vent on outlet piping.

6. If installing in conjunction with other Trapzilla products, include cleanout port before, after, and/or between each unit.

7. Do not install “P” Trap on outlet connection of tank (unit already has internal gas trap).

8. Do not reduce pipe size on outlet piping

9. Do not pressure test unit.

Equipment must be installed in compliance with all applicable laws, regulations and codes, including plumbing codes. Instal-

lation should be performed by a qualied plumbing contractor.

JOB SPECIFICATION

Grease separator(s) shall be Thermaco Trapzilla99 hydromechanical grease interceptor system(s) as manufactured by Ther-

maco, Inc., Asheboro, North Carolina as noted on plans.

SEPARATOR SPECIFICATIONS

Furnish and install __________ Thermaco Trapzilla99 Model No. TZ-1826-ECA, rotationally molded polyethylene grease

interceptor(s) for above ground installation, shall be PDI-G 101 and ASME A112.14.3 rated at 100 GPM (6.31 l/s) with 248.77

Gallons (941 L) / 1,826 lbs. (828 Kg) of total grease storage capacity with at separation efciency curve capable of holding

90% of volume in free-oating oils at capacity, with removable cover for grease and solids removal access, integral anti-otation

anchor ring for in-ground installation, integral horizontal bafe, laminar inlet ow diverter, integral vessel vent, separate storage

compartments for oil and heavier than water solids, a unitary tank body and 4” (101mm) inlet/outlet structures without gasket

interfaces, utilizing an interior radial compression ring conjoining invert to tank outlet/inlet structures without bulkhead ttings

and/or gaskets, invert top and bottom secured attachment points, sloping conical bottom for solids retention, integral sewer gas

trap, and a fully removable polyethylene self-positioning cover with sealed thread fasteners. Includes dual-entry extension collar

assembly, linear low-density rotationally molded polyethylene for eld adjustability to optimal installation depth.

SUBMITTAL OPTIONS

6” (150mm) Inlet/Outlet - Model# TZ-1826-ECA-6

Two ECA-TZ-29 Extension Collars (Two required for each TZ-1826-ECA)

TZSP-40-ECA Sampling Port with 4” Inlet/Outlet, 0.5” fall with 29” (73.7 cm) Extension Collar Assembly

TZSP-48-ECA Sampling Port with 4” Inlet/Outlet, 7.8” fall with 29” (73.7 cm) Extension Collar Assembly

TSS-95 Solids Interceptor for additional Solids Capacity

TSS-95-ECA Solids Interceptor for additional Solids Capacity with 18” (45.7 cm) adjustable extension collar

VFCA-100 Vented Flow Control Assembly for installation at plumbing xture level to limit ow to 100 gpm for installations with

head height greater than 6’

MFSH-44 Molded Flow Splitter Assembly for evenly diverting ow to two separate 4” Trapzilla units

MFSH-66 Molded Flow Splitter Assembly for evenly diverting ow to two separate 6” Trapzilla units

H20/Trafc Rated Installation, see link for installation drawings