Install Manual

©2018 Thermaco, Inc. All rights reserved • Patented/Patents Pending • Specications subject to change without notice
Thermaco, Inc. • 646 Greensboro St. • Asheboro, N. C. 27204-2548 • [phone]
MNL-TZ-1826 11
A THERMACO® Technology
Trapzilla
®
Grease Interceptor
Installation and Operations Manual
TZ-1826 Models
AEF
MNL-TZ-1826 10
1
1
2
2
3
3
4
4
A A
B B
C C
D D

THIS DRAWING CONTAINS PROPRIETARY AND PATENTED MATERIAL. THIS DRAWING MAY NOT BE REPRODUCED IN WHOLE OR PART WITHOUT
WRITTEN CONSENT FROM THERMACO, INC. POSSESSION OF THIS DRAWING DOES NOT CONSTITUTE THE RIGHT TO MANUFACTURE.
POSSESSION OF THIS DRAWING DOES CONSTITUTE AN IMPLIED NONDISCLOSURE AGREEMENT BETWEEN THERMACO, INC. AND THE HOLDER OF
THIS DRAWING. DO NOT DESTROY THIS DRAWING, IT IS THE SO
LE PROPERTY OF THERMACO, INC. AND MUST BE RETURNED UPON REQUEST.
MATERIAL (UNLESS NOTED)
FINISH (UNLESS NOTED)
646 GREENSBORO STREET
PO BOX 2548, ASHEBORO, NC 27203
VOICE 336-629-4651 FAX [phone]
Decimals
.XX +/- .03
.XXX +/- .015
Unless otherwise specified
Dimensions are in inches
Tolerances
Angular
+/- 1
°
CHECKED
SIZE
REV. NO.
DWG NO.
PART NO.
C
SCALE
RELEASE DATE
SHEET OF
ENGINEERING
DRAWN
DATE
THIRD ANG LE PROJECTIO N
3.3.3 Installing Multiple Trapzilla Units in Series
Alternatively, two Trapzilla Grease Interceptors, Solids Separators or a combination may be installed in
series. A single Trapzilla Solids Separator and Trapzilla Grease Interceptor should always be installed
in series. Place Two-Way Cleanouts before, between and after the units as shown below. Make sure
to connect an outlet vent after the Trapzilla Grease Interceptor. A Low Head Flow Control (LHFC) is
shipped with each grease interceptor and should only be installed after the rst Cleanout and before
the rst grease interceptor.
*Use a Two-Way Cleanout before and after all
Trapzilla Installations
Outlet
Inlet
*Cleanout
*Cleanout
Outlet Vents
(Connect to
facility vent)
Low-Head Flow Control (not
pictured) to be installed as
close as possible to inlet of
rst grease interceptor.
*Cleanout
Note: Drawing for reference only. Equipment must be installed in compliance with all applicable laws, regulations
and codes, including plumbing codes. Installation should be performed by a qualied plumber.
The SSA-1826 Support Stand is a one-piece assembly with a conical center that sits on the oor.
It does not add appreciable height to the assembly.
4. Above-Ground Installation
4.1 Components for Above-Ground Installations
Using a model-specic Support Stand, a Trapzilla unit may be installed directly on top of the oor in a
location such as a basement or mechanical room.
TZ-1826-SSA comes with SSA-1826 and external brace for above-ground installations. All TZ-1826
units come with built-in 18” Risers which must be cut down and secured in eld.
The External Brace must be installed in above-ground installations or the warranty will be voided.
NOTE: SUPPORT STAND
MUST BE INSTALLED OVER
A CONTINUOUS SURFACE.
NON-CONTINUOUS
SURFACES SUCH AS GRATES
ARE NOT SUITABLE FOR
SUPPORT.
1
1
2
2
3
3
4
4
A A
B B
C C
D D

THIS DRAWING CONTAINS PROPRIETARY AND PATENTED MATERIAL. THIS DRAWING MAY NOT BE REPRODUCED IN WHOLE OR PART WITHOUT
WRITTEN CONSENT FROM THERMACO, INC. POSSESSION OF THIS DRAWING DOES NOT CONSTITUTE THE RIGHT TO MANUFACTURE.
POSSESSION OF THIS DRAWING DOES CONSTITUTE AN IMPLIED NONDISCLOSURE AGREEMENT BETWEEN THERMACO, INC. AND THE HOLDER OF
THIS DRAWING. DO NOT DESTROY THIS DRAWING, IT IS THE SO
LE PROPERTY OF THERMACO, INC. AND MUST BE RETURNED UPON REQUEST.
MATERIAL (UNLESS NOTED)
FINISH (UNLESS NOTED)
646 GREENSBORO STREET
PO BOX 2548, ASHEBORO, NC 27203
VOICE 336-629-4651 FAX [phone]
Decimals
.XX +/- .03
.XXX +/- .015
Unless otherwise specified
Dimensions are in inches
Tolerances
Angular
+/- 1
°
CHECKED
SIZE
REV. NO.
DWG NO.
PART NO.
C
SCALE
RELEASE DATE
SHEET OF
ENGINEERING
DRAWN
DATE
THIRD ANG LE PROJECTIO N
TZ-1826
External Brace
(installation instructions on
next page)
SSA-1826