User's Manual

ManualsBrandsTranzeo Wireless Technologies ManualsElectronicsWIRELESS NETWORKING DEVICE

20155 Stewart Crescent,

Maple Ridge, B.C. Canada V2X 0T6

Phone (604) 460-6002 Fax (604) 460-6005

www.tranzeo.com

Revision 7/26/04 Build 51 Page 1 of 10

TRANZEO WIRELESS QUICK START GUIDE

FCC Information

This equipment has been tested and found to comply with the limits for a Class A digital devices pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communication.

Operation of this equipment in residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at this own expense.

The user should not modify or change this equipment without written approval from company name.

Modification could void authority to use this equipment.

For the safety reason, people should not work in a situation which RF Exposure limits be exceeded. To prevent

the situation happening, people who work with the antenna should be aware of the following rules

1. Install the antenna in a location where a distance of 32.5 cm from the antenna may be maintained.

2. While installing the antenna in the location, please do not turn on the power of wireless card.

3. While the device is working, please do not contact the antenna.

4. RF exposure: The antenna used for this transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter”

retrieval system, translated into any language, or transmitted in any form or by any means without the written

permission of the supplier.

About This Manual

The purpose of this manual is for the setup of the TRANZEO TR-CPE200. This manual, revised as version 1.0.0

in 2004, includes procedures assisting you in avoiding unforeseen problems.

Summary of content (10 pages)

PAGE 1
TRANZEO WIRELESS QUICK START GUIDE FCC Information This equipment has been tested and found to comply with the limits for a Class A digital devices pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 2
TRANZEO WIRELESS QUICK START GUIDE TR-CPE Quick Start Guide Introduction This next-generation wireless LAN device – the TRANZEO TR-CPE200, brings Ethernet-like performance to the wireless realm. Fully compliant with the IEEE802.11b standard, the TRANZEO TR-CPE200 also provides powerful features such as the Internet-based configuration utility, and WEP security. Maximize network efficiency while minimizing your network investment and maintenance costs.
PAGE 3
TRANZEO WIRELESS QUICK START GUIDE 2-4 Hardware Installations Take the following steps to set up your TR- CPE200. Site Selection: Before installation, determine the TR- CPE200 Units location. Proper placement of the unit is critical to ensure optimum radio range and performance. You should perform a Site Survey to choose a proper placement for your unit. Place your unit within the line of sight of the Access Point. Obstructions may impede performance of the unit.
PAGE 4
TRANZEO WIRELESS QUICK START GUIDE Connecting the Ethernet Cable Step 1 Place the Ethernet Boot Cover over the end of your Cat 5 Cable. Step 2 Attach tightening bracket on top of the Ethernet Boot. This is easiest to do before you attach the CAT 5 cable. The Gasket must be attached to the Boot so that it sits between the radio and the boot. Step 3 Insert the Cat 5 Cable and tighten the Boot Cover. Be sure to pull enough cable through to reach the RJ-45 connector with an RJ-45 jack attached.
PAGE 5
TRANZEO WIRELESS QUICK START GUIDE Step 4 Place the Ethernet boot over the 4 Screw Posts. The screws should just barely clear the tightening bracket. Apply 4 Ket nuts to the screw posts and tighten until the metal plate makes full contact with the Ethernet boot. Do not over tighten. This is an example of over tightening. Over tightening connections like this may crack the boot and will compromise the gasket seal. Over tightening is not covered by warranty.
PAGE 6
TRANZEO WIRELESS QUICK START GUIDE Connect the Power Cable To CPE To PC Connect the power adapter to the power socket on the Power over Ethernet Adaptor, and plug the other end of the power into an electrical outlet. Plug the RJ-45 Cable from the unit into the POE. The Station Adaptor will be powered on and the Red power indicator on the top panel will turn on. NOTE: ONLY use the power adapter supplied with the Access Point. Otherwise, the product may be damaged.
PAGE 7
TRANZEO WIRELESS QUICK START GUIDE HTML Interface2 NOTE: The default IP address is 192.168.1.99 System Settings Password Again Firmware Allow Upgrades Cloning Bridge Allows user to change passwords. Confirm Password Lists Diagnostic Information about internal firmware Allows User to Change Firmware Version If selected, the CPE will use the MAC address of the device it is attached to Revision 7/26/04 Build 51 20155 Stewart Crescent, Maple Ridge, B.C.
PAGE 8
TRANZEO WIRELESS QUICK START GUIDE IP Address Mode IP Address Subnet Mask Gateway Select Static to enter a valid Static IP or select DHCP address for auto select.
PAGE 9
TRANZEO WIRELESS QUICK START GUIDE Buttons Default Apply Undo Reboot Performance – - Resets the Radio to factory Defaults Save Changes and reset Radio Clear any changes not applied Reboot the radio Loads the test page Performance Shows all available Access Points using the SSID in this radio. Hint: Leave the SSID field blank to see all APs in the area. Shows your current TX rate and the quality of the link. The signal level is in dbm.
PAGE 10
TRANZEO WIRELESS QUICK START GUIDE RF Exposure Evaluation FCC 1.1310 states that the criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to RF radiation as specified in 1.