Tranzeo TR-CPE Quick Start Guide Introduction This next-generation wireless LAN device – the TRANZEO TR-CPE, brings Ethernet- like performance to the wireless realm. Fully compliant with IEEE802.11b standard, the TRANZEO TR-CPE also provides powerful features such as the Windows-based configuration utility, and WEP security. Maximize network efficiency while minimizing your network investment and maintenance costs. Revision 5/1/2003 Unit 13 – 11720 Stewart Crescent, Maple Ridge, B.C.
Tranzeo TR-CPE Quick Start Guide FCC Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: The Manufacturer is not responsible for any Radio or TV interference caused by una uthorized modifications to this equipment. equipment.
Tranzeo TR-CPE Quick Start Guide Table Of Contents Introduction 1 Product Kit 4 LED Definition 5 Activity 5 Description 5 Power Supply 5 Installing the TRANZEO TR-CPE 6 Site Selection 6 Tools Required to Install 6 Connecting the Ethernet Cable 7 Attaching the Mounting Bracket 9 Connect the Power Cable 9 Configuring the TRANZEO TR-CPE 10 Wireless Station Adapter Utility 10 Assigning the ESSID 11 Assigning the Adapter’s Name 12 Assigning the Rate 12 Assigning the IP Address
Tranzeo TR-CPE Quick Start Guide Hardware Installation Product Kit Before installation, make sure that you have the following items: The TR CPE x1 DC Power Adapter x1 Power over Ethernet Adapter x1 Ethernet Boot x1 Ethernet Boot Tightening Bracket x1 Mounting Bracket x1 Ket Nuts (With Washer Attached) x8 U-Bolt w/ 2 Nuts x1 RJ-45 Patch Cable x1 Product CD x1 Spare Ethernet Boot Gasket x1 If any of the above items is not included or damaged, please contact your local dealer for support
Tranzeo TR-CPE Quick Start Guide Mechanical Description LED panel of the Wireless LAN Smart Access Point: The following table provides an overview of each LED activity: LED Definition Activity PWR Green WLAN Green Description Power enabled Off: No Wireless LAN traffic activity On: Associated to the Wireless AP and Wireless LAN traffic activity. Off: No Ethernet traffic activity LAN Green Flashing: Wired LAN traffic activity On: Connect to the Ethernet.
Tranzeo TR-CPE Quick Start Guide Installing the TRANZEO TR-CPE Take the following steps to set up your TRANZEO CPE. Site Selection Before installation, determine the TR Units location. Proper placement of the unit is critical to ensure optimum radio range and performance. You may use the Site Survey and Access Points Browser utility (The utilities included with the wireless PC Card) to choose a proper placement for your unit. Place your unit within the line of sight of the Access Point.
Tranzeo TR-CPE Quick Start Guide Connecting the Ethernet Cable Step 1 Place the Ethernet Boot Cover over the end of your Cat 5 Cable. Step 2 Attach tightening br acket around on top of the Ethernet Boot. This is easiest to do before you attach the CAT 5 cable. Step 3 Insert the Cat 5 Cable and tighten the Boot Cover. Be sure to pull through enough cable to reach the RJ-45 connector with an RJ-45 jack attached. Hands tighten only. DO NOT OVERTIGHTEN as you may damage the environment seal.
Tranzeo TR-CPE Quick Start Guide Step 4 Place the Ethernet boot over the 4 Screw Posts. The screws should just barely clear the tightening bracket. Apply 4 Ket nuts to the screw posts and tighten until the metal plate makes full contact with the Ethernet boot. Do not over tighten. This is an example of over tightening. Over tightening connections like this may crack the boot and will compromise the gasket seal. Over tightening is not covered by warranty.
Tranzeo TR-CPE Quick Start Guide Attaching the Mounting Bracket Step 1 As shown below, the U -Bolt is designed to mount around a pole. Tighten bolts sufficiently to prevent any movement. Step 2 Down or up tilt can be adjusted by using the swinging the unit before tightening the U-Bolt. Connect the Power Cable Connect the power adapter to the power socket on the Power over Ethernet Adaptor, and plug the other end of the power into an electrical outlet. Plug the RJ-45 Cable from the unit into the POE.
Tranzeo TR-CPE Quick Start Guide Configuring the TRANZEO TR-CPE The TRANZEO TR-CPE allows configuration either via the configuration utility, known as Wireless Station Adapter Utility, and Web Management. Wireless Station Adapter Utility The following gives instructions guiding you through the installations of the Wireless Station Adapter Utility. 1. Insert the Product CD into the CD-ROM drive on your computer. 2. Browse to the CD ROM and open the TR-CPE Folder. 3. Open the TR-CPE 1.6 Utility folder. 4.
Tranzeo TR-CPE Quick Start Guide INFO: This item shows the current information on the TR-CPE such as ESSID, Adapter’s name, Rate, IP Address, subnet mask, and default gateway. You may click the SETUP button to configure those parameters. Assigning the ESSID The ESSID is a unique ID used by Access Points and Stations to identify a wireless LAN. Wireless clients associating to any Access Point must have the same ESSID. The default ESSID is ANY. The ESSID can have up to 32 characters.
Tranzeo TR-CPE Quick Start Guide Assigning the Adapter’s Name Assign specificity a unique name for the TR-CPE. Assigning the Rate TR-CPE provides various data rate options for you to selec t. Data rates options include 1 Mbps, 2 Mbps, 5.5 Mbps, 11 Mbps, and Auto. In most networking scenarios, you will see that the factory-set default “Auto” will prove the most throughput. Assigning the IP Address Assign an IP address to your TR-CPE if you wish to configure the TR-CPE via the Web Management.
Tranzeo TR-CPE Quick Start Guide WEP To enable the WEP encryption, select the encryption type, either 40 bit or 128 bit, Key Format ASCII, Hex, or Passphrase. Then enter a WEP Key in the EDIT Key field. For 40 bit encryption you may choose: n n ASCII: 5 characters (case sensitive) ranging from “a-z”, “A-Z” and “0-9” (e.g. MyKey) Hex: 10 hexadecimal digits in the range of “A-F”, “a-f” and “0-9” (e.g.
Tranzeo TR-CPE Quick Start Guide After defining the WEP keys, click the APPLY button to make the configuration take effect. STATUS: The STATUS item allows you to monitor the general information of the Access Point with which TR-CPE is communicating, such as the Link status, Channel, ESSID, BSSID, Signal, RX and TX. AP BROWSER: By clicking the Refresh button, the AP Browser will reload and display the available Access Points around the working environment.
Tranzeo TR-CPE Quick Start Guide ABOUT: The About button display the version of the TR-CPE Utility software and firmware version of the TR-CPE. Revision 5/1/2003 Unit 13 – 11720 Stewart Crescent, Maple Ridge, B.C. Canada V2X 9E7 Phone (604) 460-6002 Fax (604) 460-6005 www.tranzeo.
Tranzeo TR-CPE Quick Start Guide Firmware Upgrade Utility When you finished the installation of the TR-CPE utility, you will find the Firmware upgrade utility in the TR-CPE utility Programs Folder. When you start the Firmware upgrade utility, it will browse for all of the TR-CPE’s available on the network. Select the TR-CPE you want to upgrade. Enter the password and click the LOGIN button. You will be able to upgrade Firmware of the TR-CPE utility as you desire.
Tranzeo TR-CPE Quick Start Guide Web Management The built-in Web Management provides you with a set of user-friendly graphical user interface to manage your TR-CPE. With the assigned IP address of the TR-CPE, you may get access to the TR-CPE via a web browser (e.g., Netscape Navigator 3.0 ~ 4.5 or MS Internet Explorer 4.0) to monitor and configure the TR-CPE. Technical Support You can find the most recent software and updated user documentation will be updated periodically on the Tranzeo Web site.
Tranzeo TR-CPE Quick Start Guide This page outlines Tranzeo Wireless, Inc's RMA policy and will guide you on what to do in case an RMA is required. Warranty 1. Tranzeo Wireless manufactured products are warranted against defects in material and workmanship for a period of one year from date of purchase, under normal use. 2. Tranzeo Wireless will repair or replace a product that was found to be defective by Tranzeo during the warranty period at its discretion. a.
Tranzeo TR-CPE Quick Start Guide Who do I contact for an RMA? To discuss your technical difficulties and request an RMA # please call the Technical Support Center at 604-460-6002 or email rma@tranzeo.com. Warranty Repair (a) Your RMA number is valid for 15 days only. (b) If the product is not received within 15 days, the RMA will be cancelled. (c) Tranzeo Wireless will carefully test and evaluate all returned products and will repair or replace defective products that are under warranty at no charge.
Tranzeo TR-CPE Quick Start Guide (k) Be sure to package the items well. Original packaging should be used for shipping. Tranzeo is not responsible for further damage caused to the unit due to inadequate packaging. (l) We require that you use UPS Air to ship your RMA. UPS Air includes all brokerage charges, making it the most cost effective method of shipping to Canada. Tranzeo will not accept any packages that arrive with charges owing. (m) Be sure to include the password for each device.
