!" #$%&" '($)*!+#,$$) *$#*$- +)- ./&)- */ 0/('1 23" *! *!$1 " (" *#./4+ 1 +## -" 5" *+1-$6" 0$#'&4#&+)**/ '+4* /.*!$ &1 $# !$#$1 " (" *#+4$-$#" 5)$- */ '4/6" -$4$+#/)+,1 $'4/*$0*" /) +5+" )#*!+4(.&1" )*$4.$4$)0$3!$) *!$$%&" '($)*" #/'$4+*$-" )+0/(($40" +1$)6" 4/)($)* !" #$%&" '($)*5$)$4+*$# &#$# +)- 0+) 4+-" +*$4+-" / .4$%&$)02$)$452+)- " .)/*" )#*+1 1 $- +)- &#$- " ) +00/4-+)0$ 3" *!*!$" )#*4&0*" /)(+)&+1(+20+&#$!+4(.&1" )*$4.$4$)0$*/4+-" /0/((&)" 0+*" /) '$4+*" /) /.
, , ! ! - !& !& Introduction This next-generation wireless LAN device – the TRANZEO TR-AP-5amp-N, brings Ethernet-like performance to the wireless realm. Fully compliant with the IEEE802.11a standard, the TRANZEO TR-AP-5amp-N also provides powerful features such as the Internet-based configuration utility, and WEP and WPA security. Maximize network efficiency while minimizing your network investment and maintenance costs.
Power Supply: ONLY use the power adapter supplied with the TR- AP-5a. Otherwise, the product may be damaged. www.tranzeo.com 20155 Stewart Crescent, Maple Ridge, B.C.
2-4 Hardware Installations Take the following steps to set up your TR-AP-5amp-N. Site Selection: Before installation, determine the TR-AP-5amp-N Units location. Proper placement of the unit is critical to ensure optimum radio range and performance. You should perform a Site Survey to choose a proper placement for your unit. Place your unit within the line of sight of the Access Point. Obstructions may impede performance of the unit.
Connecting the Ethernet Cable Step 1 Place the Ethernet Boot Cover over the end of your Cat 5 Cable. Attach the sticky side of the gasket to the underside of the Ethernet Boot. Step 2 Attach Ethernet Cable Lock on side of the Ethernet Boot. This is easiest to do before you attach the RJ-45 Jack. Step 3 Tighten using a ¾” wrench or socket. Tighten until the Cable Lock touches the Boot as shown in Step 3. USE HAND TOOLS ONLY. DO NOT OVERTIGHTEN as you may damage the environment seal. www.tranzeo.
Step 4 Attach optional tightening bracket on top of the Ethernet Boot. This is easiest to do before you attach the CAT 5 cable. The Gasket must be attached to the Boot so that it sits between the radio and the boot. Step 5 Insert the Cat 5 Cable and tighten the Boot Cover. Be sure to pull enough cable through to reach the RJ-45 connector with an RJ-45 jack attached. Attach tightening bracket on top of the Ethernet Boot. This is easiest to do before you attach the CAT 5 cable.
This is an example of over tightening. Over tightening connections like this may crack the boot and will compromise the gasket seal. Over tightening is not covered by warranty. Attaching the Mounting Bracket As shown below, the U-Bolt is Tighten bolts sufficiently to prevent designed to mount around a pole. any movement. Down or up tilt can be adjusted by swinging the unit before tightening the U-Bolt.
Connect the Power Cable Connect the power adapter to the power socket on the Power over Ethernet Adaptor, and plug the other end of the power into an electrical outlet. Plug the RJ-45 Cable from the unit into the POE. The Station Adaptor will be powered on and the power indicator on the top panel will turn on. NOTE: ONLY use the power adapter supplied with the Access Point. Otherwise, the product may be damaged. This unit must be grounded.
HTML Interface NOTE: The default IP address is 192.168.1.100 Select the option in the frame on the left you wish to configure. www.tranzeo.com 20155 Stewart Crescent, Maple Ridge, B.C.
Wireless Settings SSID Turbo Mode www.tranzeo.com The SSID is a unique ID given to an Access Point. Wireless clients associating to the Access Point must have the same SSID. The SSID can have up to 32 characters. HINT: Entering “none” the field allows the unit to see all AP’s in the area. When using turbo mode, the other device must also support Turbo Mode. Also, the channel must be set manually on the AP. 20155 Stewart Crescent, Maple Ridge, B.C.
Security Basic Enabled Key Length Shared Key Authentication Keys www.tranzeo.com Turn On WEP Level of Encryption. NOTE: 64 bit is called 40 bit on some systems Turn on Shared Key Authentication Enter your WEP keys. NOTE: Keys must be entered in HEX only. 20155 Stewart Crescent, Maple Ridge, B.C.
Security Advanced Enabled Encryption Type Turn On WPA Level of Encryption. TKIP or AES Enabled Authentication 802.1x for Radius Server www.tranzeo.com 20155 Stewart Crescent, Maple Ridge, B.C.
Access Control Click on stations in Wireless Devices Available to enter station in Allowed Stations or Click in Associated Wireless Devices to delete it. www.tranzeo.com 20155 Stewart Crescent, Maple Ridge, B.C.
Station List www.tranzeo.com 20155 Stewart Crescent, Maple Ridge, B.C.
. " $ / What is a proper Ground? This antenna must be grounded to a proper Earth Ground.
Where to Ground the device This radio must be grounded at the Pole AND at the POE. This is because the radio is between the Exterior Antenna and the POE ground. See the examples below Ungrounded Radio An ungrounded radio causes the surge to pass through the radio. In this case the radio most likely will be damaged. ` Antenna Radio POE Ground Grounded Radio An grounded radio causes the surge to pass directly to ground, bypassing the radio. Antenna Radio POE Ground www.tranzeo.
Ungrounded POE Mounting Pole In this case, the surge will be picked up by the Cat 5 cable, and since the POE is not grounded, the route for the surge is through the radio to the antenna, and out through the building. POE Cat 5 Cable Grounded POE Mounting Pole In this case, the surge will be picked up by the Cat 5 cable, and since the POE is grounded, the route for the surge is through the POE to ground. Ground POE Cat 5 Cable www.tranzeo.com 20155 Stewart Crescent, Maple Ridge, B.C.
Best Practices 1) Allow try to run the Cat5 and LMR inside of the mounting pole wherever possible. This helps to insulate the cable from any air surges. Building Cat 5 Cable 2) Keep all runs as straight as possible. Never put a loop into the cables. 3) Test all grounds to ensure that you are using a proper Ground. If using a electrical socket for Ground, use a socket tester, such as Radio Shack 22-141 4) Buy a copy of the National Electrical Code Guide and follow it.
