MMDS Transmitter Operation Manual Copyright 2007, TRANSYSTEM, INC. All rights reserved TRAN SYSTEM I N C. No.1-2 Li-Hsin Rd.I Science-Based Industrial Park, Hsinchu, Taiwan Tel:+886-3-5780393 Fax:+886-3-5784111 e-mail: sales@transystem.com.tw website: www.transystem.com.
*Contact Us: The Headquarter Tel : + 886-3-578-0393 Fax: + 886-3-578-4111 Website: http://www.transystem.com.tw E-mail: sales@transystem.com.tw Address: NO. 1-2, LI-HSIN RD.
TABLE OF CONTENTS Chapter 1. Chapter 2. Chapter 3. General Information 4 1.1 Module Features and Specifications 4 Installation 5 2.1 Step by Step Installation 5 2.2 Connection to the Power Inserter and Cable Modem 8 2.3 Waterproofing Connections 10 Accessories 12 3.
Chapter 1. General Information 1.1 Module Features and Specifications Input Frequency Output Frequency Output 1 dB Compression Point Output Transmitting Noise Output Spurious (+22dBm TX Out) Output Power Blanking Threshold TX Switching Latency LO Stability Phase Noise Input and Output Return Loss Input Impedance Output Impedance Supply Voltage Supply Current Temperature Humidity Lightning & Surge Protection PLC100 22~34 MHz PLC200 12~42 MHz 2170~2182MHz 24dBm Typ. 2500~2530MHz 24dBm Typ.
Chapter 2. Installation 2.1 Step by Step Installation 2.1.1 Mounting Bracket Assembly Suite The following hardwares are suggested for mounting the Transmitter to the pole. A set of mounting bracket includes ONE 2511 mounting bracket, ONE bracket 3, ONE bracket 2, TWO screws 4013, and FOUR hex flange nuts. Please contact TSI sales department for this accessory.
2.1.2 Step by Step Installation Step 1 – Attach sequence Left to right: Bracket 3, Bracket 2, and 2511 Mounting Bracket. Step 2 – How to Attach The concave of Bracket 2 is for holding onto the pole.
Step 3 – Tighten the bracket against pole Step 4 – Installation Complete Loosen Screws A & B for left-and-right and up-and-down angle adjustments. Tighten up Screws A & B after fixing the directions.
2.2 Connection to the Power Inserter and Cable Modem Connections to the Transmitter are shown in diagram 2.2. Please note: ① The power inserter normally has 3 ports: DC Connect to wall adapter with RG-59 cable ANT Connect to the Transmitter TV Connect to Cable modem VERY IMPORTANT NOTICE! a. The power inserter should be correctly connected, or the Transmitter will not operate. b. Ensure that all wires and cables are hooked up before plugging into the AC adapter/power supply (i.e.
② After connection, the F connector of Transmitter must be sealed with an asphalt sealing tape. (For details, please refer to Section 2.3 Waterproofing Connections) Diagram 2.
2.3 Waterproofing Connections Water-proofing is very important during installation of Transmitter. Please use the included water-proof asphalt tape to seal off the F-connector as shown below: ① After you plug in the coaxial cable into the F-connector, use the included water-proofing asphalt tape to seal off the F-connector from the bottom (i.e. the part close to Transmitter). Note that the tape must wrap up all the thread of the F-connector. ② The wrap up of the tape must be tight and sturdy.
③ The total width of the wrap-around is about 6cm, which corresponds to 7 to 8 rounds of tapes. * Warning: If you do not follow the above procedure, the Transmitter could become malfunctioning due to water leakage.
FCC Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. CAUTION: Change or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
PLC-200 PLC-200 is TSI’s latest offering for 2-way wireless broadband Internet application. It accepts an IF signal of 12~42MHz from cable modem, upconverts the signal to 2500~2530MHz and transmits it back to the MMDS headend site. With a built-in automatic on/off switch, PLC-200 will enter sleep mode to eliminate broadband noise when there is no data packet transmission. Without exception, PLC-200 embodies the long term stability and reliability common to all TSI products.
