SISTG10xx-111-LR(T) 10/100/1000Base-T to 1000Base-X Industrial Media Converter Installation Manual Rev.
Transition Networks Table of Contents Trademark, copyright, and product classification information ......................................................................... iii Trademark.................................................................................................................................................. iii Copyright restrictions ................................................................................................................................. iii FCC warning .....
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter Section III: ...............................................................................................................................................................22 Advanced Features .................................................................................................................................................22 Introduction .........................................................................................
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Trademark, copyright, and product classification information Trademark All trademarks and registered trademarks are the property of their respective owners. Copyright restrictions © 2008 Transition Networks: All rights reserved. No part of this work may be reproduced or used in any form or by any means—graphic, electronic, or mechanical—without written permission from Transition Networks. Printed in the U.S.A.
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter About this product and manual Industrial Media Converter The SISTG10xx-111-LR(T) Industrial Media Converter provides a 10/100/1000Base-T (RJ-45) copper connection and a 1000Base-X fiber connection with either a fixed optical transceiver or an SFP port. These Media Converters are hardened devices designed to reliably operate in harsh environments such as those found on factory floors, outdoor enclosures or other hazardous environments.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Cautions and warnings Cautions and warnings Make sure that you read and understand all content identified by these two symbols: Cautions and warnings appear here and throughout this manual where appropriate. Failure to read and understand the information identified by the “caution” and “warning” symbols could result in poor equipment performance, damage to equipment, or injury to persons.
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter Cautions and warnings, continued Warnings Warnings indicate the possibility of injury to persons. WARNING Be sure to disconnect power before installing and wiring the Media Converter. Failure to observe this warning could result in an electrical shock. WARNING Fiber optics: Visible and invisible laser radiation when open: DO NOT stare into the beam, or directly view the beam with optical instruments.
Section I SISTG10xx-111 Industrial Media Converter In this section These are the topics: Topic General description SISTG10xx-111 Industrial Media Converter model numbers Package Contents Physical Description See Page 2 3 4 5
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter General description Overview The SISTG10xx-111 Industrial Media Converter can help eliminate EMI or RFI issues and help to overcome distance limitations with copper-based cabling by providing a fiber interface to transport data from copper-based industrial networking and communication devices over fiber optic cabling.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks SISTG10xx-111 Industrial Media Converter part numbers Standard models The part numbers shown in Tables 1 and 2 perform as described in this manual. Table 1: Industrial Media Converter Part Numbers Standard Operating Temperature (-10°C to +50°C) Part Number Port 1: 10/100/1000Base-T SISTG1013-111-LR RJ-45 100 m (328ft) SISTG1014-111-LR SISTG1040-111-LR Port 2: 1000Base-X SC, 850 nm multimode [62.5/125µm: 220 m/722 ft.
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter Package contents Package contents Quantity 1 1 2 8 1 1 Description 10/100/1000BaseT to 1000BaseX Industrial Media Converter DIN-Rail mounting bracket (installed) Wall mount brackets Screws (for attaching wall-mount bracket) Installation manual CD Barrel connector interface cable - For external AC/DC power supply (sold separately) Compare the package contents of your industrial media converter with the standard checklist above.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Physical description Physical dimensions Width: 1.2” [30mm] Height: 5.5” [140mm] Depth: 3.
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter Physical description, continued Bottom panel The top view of the Media Converter is shown in Figure 2 with corresponding descriptions listed below: 6-position terminal block Grounding Screw Primary power input terminals (2) Secondary power input terminals (2) Contact relay output terminals (2) Figure 2: SISTG10xx-111-LR(T) Industrial Media Converter (Top View) Back panel The back view of the Media Converter is shown in Figure 3 wit
Section II Installation In this section These are the topics: Topic DIN rail mounting Wall mounting Grounding the Media Converter Connecting power to the Media Converter Connecting an alarm fixture Connecting fiber cable Connecting copper cable DIP switches Light Emitting Diodes (LEDs) See Page 8 10 11 12 16 18 19 20 21
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter DIN rail mounting DIN rail clip The Media Converter includes an aluminum DIN Rail Clip attached to the rear panel. Verify the clip is attached and oriented as pictured in Figure 4 below.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks DIN rail mounting, continued DIN rail mounting To mount the Media Converter to the DIN rail, see Figure 5 and do the following: Step Action 1. Align and then position DIN-Rail-clip spring to the top of the DIN rail as shown in Figure 5, step (a). 2. Press DOWN on the Media Converter and then IN to snap it into place on the DIN Rail. See Figure 5, step (b).
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter Wall mounting Wall mount bracket The Media Converter includes a wall mount bracket and screws in the contents of the shipping package. The wall mount bracket can be attached to the rear panel of the Media Converter to enable mounting to a vertical surface such as the wall of an enclosure. Locate the brackets (2) and screws (8) and follow the steps below to install the bracket on the Media Converter.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Grounding the Media Converter CAUTION Be sure to disconnect the Media Converter from the DC power source before installing and wiring the device. Wiring considerations The following wiring considerations are recommended: • Signal lines must not be directly connected to outdoor wiring. • Use separate paths or conduits to route wiring for power and device data cables.
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter Connecting power to the Media Converter Redundant power inputs The Media Converter has dual (redundant) power inputs capable of auto-sensing the input voltage, while providing over current protection and reverse polarity protection. The dual power inputs can be connected simultaneously to live DC power sources. See Figure 8.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Connecting power to the Media Converter, continued Note: Terminal-block wiring The terminal block can accept 12 – 24 AWG wire for power and alarm relay inputs. To wire the 6-position terminal block for redundant power, do the following: Note: Step 1. 2. 3. 4. 5. The 6-position terminal-block plug is constructed (keyed) to mate with the Media Converter terminal block.
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter Connecting power to the Media Converter, continued Terminal-block wiring (continued) Step 6. Action Insert the terminal block plug into the Media Converter’s terminal block, as shown in Figure 10. Figure 10: Wired Terminal Block Plug Inserted Into Media Converter 7. 8. 14 Make sure that the DC power source is stable and clean.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Connecting power to the Media Converter, continued Barrel connector interface cable A barrel connector interface cable is included with the Media Converter and can be used to convert the barrel connector output of an external AC/DC power supply over to a wire interface that can then be inserted into the terminal block following the instructions and figure 9, both located on page 13 of this manual.
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter Connecting an alarm fixture Alarm relay The Media Converter has dry relay contacts for connecting an external alarm fixture. Located on the green terminal block on the top panel, the relay has “normally open” contacts that can be wired to form a circuit for triggering an external alarm when a fault occurs (light or audible alarm). See Figure 12.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Connecting an alarm fixture, continued Fault indications Wire the relay contacts to any warning light or audible alarm in the control room as shown in Figure 14. When a fault occurs, the relay contacts open, stopping the flow of current through the contact circuit. This will disable the external alarm or turn OFF a light, indicating a fault.
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter Connecting fiber cables Fiber cable installation When connecting fiber cables to the 1000BASE-X port on the Media Converter, make sure the correct type is used: LC or SC. To install the fiber cables, do the following: Step 1. Action Remove and keep the fiber-port protective dust cover(s).
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Connecting copper cables Copper cable installation To connect the copper cable to the Media Converter and other equipment, do the following: Step 1. 2. 3. 4. Action Locate or build 10Base-T or 100Base-TX or 1000Base-T compliant copper cables with male, RJ-45 connectors installed at both ends. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on the media converter. See Figure 16 below.
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter DIP Switches DIP switch position descriptions The Media Converter features two DIP switches on the front panel used to configure the Media Converter for use in a particular network setting. Figure 18 shows the DIP switches and a chart that explains each setting.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Light Emitting Diodes (LEDs) LEDs The Media Converter has LED indicators located on its front panel. The LEDs present at-aglance network status, and provide real-time connectivity information. Figure 19 shows the LEDs and a chart that explains the function of each.
Section III: Advanced Features Introduction This section provides an explanation of the advanced features on the Media Converter.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Advanced Features AutoCross TM TM AutoCross automatically detects and configures the twisted pair port on the converter to the correct MDI or MDI-X configuration allowing either straight-through (MDI) or crossover (MDI-X) cables to be used – see figure 20. No user intervention is required.
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter Advanced Features, continued Link Pass Through Link Pass Through is a troubleshooting feature that allows the media converter to monitor both the fiber and copper RX ports for loss of signal. In the event of a loss of RX signal on one media port, the converter will automatically disable the TX signal of the other media port, thus "passing through" the link loss.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Section IV: Cable Specifications Introduction This section provides copper and fiber cable specifications.
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter Copper (RJ-45) cable specifications Copper cabling Shielded twisted-pair (STP) or unshielded twisted-pair (UTP) cabling may be used and can be configured as either Straight-through or crossover – see figure 22.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Fiber cable and optic specifications Fiber cable characteristics Fiber optic specifications Cable physical characteristics must meet or exceed IEEE 802.3™ specifications. Parameter Specification Bit Error Rate: Single mode fiber: Multimode fiber: Multimode fiber: <10 9 µm 62.
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter Section V: Troubleshooting Introduction This section provides basic troubleshooting information for the Media Converter via a problem and corrective action table. The problems are stated in the problem column and the action(s) to take for the problem is stated in the corrective action column.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Troubleshooting problem and corrective action table Problem Media Converter does not power up No link or activity on the UTP port No link or activity on the Fiber port Potential Cause • Is the wired terminal-block plug fully inserted into the Media Converter? Potential Solution • Wire and insert the terminal-block plug into the Media Converter’s terminal block – See pages 12-16 • Is the power LED lit? • Check that DC power is at the
Section VI: Contact Us, Warranty, & Compliance Information Introduction This section explains how to contact Transition Networks via Phone, fax, email, and direct mail.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Contact us Technical support Technical Support is available 24 hours a day. United States: 1-800-260-1312 International: 00-1-952-941-7600 Live Web chat Chat live via the Web with a Transition Networks Technical Support Specialist. Log onto www.transition.com and click the Transition Now link. Web-based training Transition Networks provides 8-10 seminars per month via live web-based training. Log onto www.transition.
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter Warranty Limited lifetime warranty Effective for products shipped May 1, 1999 and after, every Transition Networks’ labeled product will be free from defects in material and workmanship for its lifetime. This warranty covers the original user only and is not transferable.
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks Warranty, continued Customer pays non-compliant return costs The customer must pay the non-compliant product(s) return transportation cost to Transition Networks for evaluation of said product(s) for repair or replacement. Transition Networks will pay for shipping the repaired or replaced in-warranty product(s) back to the customer (any and all customs charges, tariffs, or/and taxes are the customer’s responsibility).
Transition Networks SISTG10xx-111-LR(T) Industrial Media Converter Compliance information Compliances CISPR22/EN5022 Class A + EN55024; EN60950 Class A; FCC Class A; CE Mark UL Listed; C-UL Listed The following part numbers are UL Listed: SISTG1040-111-LR, SISTG1040-111-LRT, SISTG1013-111-LR, SISTG1013-111-LRT, SISTG1014-111-LR, SISTG1014-111-LRT.
SISTG10xx-111-LR(T) Industrial Media Converter European Regulations, (continued) Transition Networks In accordance with European Union Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003, Transition Networks will accept post usage returns of this product for proper disposal. The contact information for this activity can be found in the ‘Contact Us’ portion of this document. CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBLIC TELEPHONE NETWORK.
Appendix A: Technical Specifications SISTG10xx-111-LR(T) specifications, notices, and warnings Parameter Standards Regulatory Compliance for Emissions Safety Compliance EMI Compliance Environmental Compliance Ports Fiber Optic Specifications Max Distance Max Data Rate Signals Power Consumption Ingress Protection MTBF (MIL-HDBK-217F) Input Power Dimensions Weight Shipping weight Standard Operating Temperature (-LR models only) Extended Operating Temperature (-LRT models only) Storage Temperature Operat
SISTG10xx-111-LR(T) Industrial Media Converter Transition Networks SISTG10xx-111-LR(T) specifications, notices, and warnings, continued Notices • The information in this user’s guide is subject to change. For the most up-to-date information on the SISTG10xx-111-LR(T) Industrial Media Converter, please refer to the user’s guide on-line at: www.transition.com. • Product is certified by the manufacturer to comply with DHHS Rule 21/CFR, Subchapter J applicable at the date of manufacture.
