Network Cables User Manual

8
SCSCF30xx-10x
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Cable Specifications -- Continued
SCSCF3029-102 1310 nm (TX) / 1550 nm (RX) simplex
SCSCF3029-103 1550 nm (TX) / 1310 nm (RX) simplex
Fiber-optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm
Fiber-optic Receiver Sensitivity: min: -33.0 dBm max: -3.0 dBm
Link Budget: 25.0 dB
CSCSCF3039-100 1300 nm multimode
Fiber-optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm
Fiber-optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm
Link Budget: 11.0 dB
The fiber optic transmitters on this device meet Class I Laser safety requirements per
IEC-825/CDRH standards and comply with 21 CFR1040.10 and 21CFR1040.11.
Technical Specifications
For use with Transition Networks Model SCSCF30xx-10x or equivalent
Standards FCC Class A; EN 55022 Class A; EN 55024; ANSI
T1.102-1993; ETSI TBR-24; ITU-T G.703 G.823 for jitter
tolerance; G.775 for loss of signal; Telecordia GR-
499CORE & GR-253-CORE
Data Rate DS3 / T3 = 44.7 Mb/s; E3 = 34.4 Mb/s
Dimensions 3.25" x 4.7" x 1.0" (83 mm x 119 mm x 25 mm)
Weight 10 oz. (283 g) approximately
Power Consumption 6.0 Watts
Power Supply 12 VDC, 0.8 Amp (minimum)
DC Outlet Minimum output regulation: 5%
MTBF (stand alone) 48,996 (MIL217F2 V5.0) (MIL-HDBD-217F)
119,854 (Bellcore7 V5.0)
Environment Tmra*: 0 to 50°C (32° to 122°F )
Storage Temp: -20° to 85°C (-4° to 185°F)
Humidity: 5 to 95%, non condensing
Altitude: 0 to 10,000 feet
Warranty Lifetime
*Manufacturer’s rated ambient temperature.
For the most up-to-date information on the SCSCF30xx-10x Device, view the user’s
guide on-line at www.transition.com.
Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,
Subchapter J applicable at the date of manufacture.
CAUTION:
Visible and invisible laser radiation when open. Do not stare into beam
or view directly with optical instruments.
CAUTION:
Use of controls, adjustments or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
[e-mail] -- Click the “Transition Now” link for a live Web chat.
9
Troubleshooting
If the Device fails, isolate and correct the failure by determining the answers to the
following questions and then taking the indicated action:
1. Is the PWR (Power) LED on the Device illuminated?
NO
• Ensure that the power adapter is the proper type of voltage and cycle
frequency for the outlet.
• Ensure the power adapter is properly installed in the Device and in the
grounded outlet.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 2.
2. Is the SDC (Signal Detect / Coax) LED illuminated green?
NO
• Check the coax cables for the proper connection.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 3.
3. Is the SDF (Signal Detect / Fiber) LED illuminated green?
NO
• Check the fiber cables for proper connection.
• Verify that the TX and RX cables on the local Device are connected to
the RX and TX ports, respectively, on the remote Device.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 4.
4. Is the SDC (Signal Detect / Coax) LED flashing green?
YES
• The coax link is in loop-back mode. For normal operation, set the loop-
back switch to the center (normal) position.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
NO
• Proceed to step 5.
5. Is the SDF (Signal Detect / Fiber) LED flashing green?
YES
• The fiber link is in loop-back mode. For normal operation, set the loop-
back switch to the center (normal) position.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
NO
• Proceed to step 6.