Leaflet
Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com
©2011 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
Specifications
Standards ANSI, ITU-TS, ETSI, G.823 for jitter tolerance,
G.755 for loss of signal
Coax Connectors 75 ohm coax
Fiber Connectors SFP: LC connector Uses standard 100BASE-X/OC-3 SFP
Fixed Optics: ST or SC connector
Data Rates DS3/T3 = 44.7Mbps; E3 = 34.4Mbps
Status LEDs Power, Coax link status, coax loop-back status, AIS on coax
link; Fiber link status, fiber loop-back status, AIS on fiber link
Dimensions W: 3.5” [82 mm]; D: 6.5” [165 mm]; H: 1.0” [25 mm]
Power Consumption 2.4 Watts
Power Input: 100-240 VAC
Output: 12 VDC
Operating Temp -10°C to 65°C
Altitude 0-10,000 Feet
Operating Humidity 5-95% (non-condensing)
Shipping Weight 2.0 lbs. [0.90 kg]
Regulatory Compliance CISPR/EN55022 Class A; FCC Class A; CE Mark, UL60950
MTBF w/Power Supply Greater than 41,660 hours (MIL-HDBD-217F)
Greater than 114,580 hours (Bellcore)
MTBF w/o Power Supply Greater than 250,000 hours (MIL-HDBD-217F)
Greater than 687,000 hours (Bellcore)
Warranty Lifetime
DS3 – T3/E3 Coax to Fiber Network Interface Device
Features
AIS (Alarm Indication Signal)
Coax Line Build Out
Switch selectable for DS3/T3 or E3
Remote firmware upgrade
Loopback – Coax and Fiber
LEDs for immediate visual status
Supports dual or single fiber
Supports multimode and single mode
fiber at a variety of distances
Supports CWDM SFPs
SNMP management when used with
ION chassis and management module
Remote standalone can be managed
by local peer
The DS3 – T3/E3 copper to fiber network
interface device (NID) provides a solution
for those users that need to extend DS3
connections over fiber.
The DS3 – T3/E3s supports Small Form
Pluggable (SFP) transceivers to support a
variety of fiber types, distances and
wavelengths to provide maximum flexi-
bility across a variety of network topolo-
gies. The use of Coarse Wave Division
Multiplexing (CWDM) SFPs can be utilized
to further increase the bandwidth capac-
ity of the fiber infrastructure.
The DS3 – T3/E3 NID must be used in
pairs. A typical installation will include a
chassis card installed in the ION Platform
locally and a stand-alone device installed
at the remote location.
Integrate Voice & Data on Fiber Network
S6210 Series
stand-alone device for the ion platform
DS3 – T3/E3
The ION Platform
Ordering Information
S6210-3011
(2) Coax (BNC)
to 1300nm multimode (ST)
[2 km/ 1.2 mi.] Link Budget: 11.0 dB
S6210-3013
(2) Coax (BNC)
to 1300nm multimode (SC)
[2 km/ 1.2 mi.] Link Budget: 11.0 dB
S6210-3014
(2) Coax (BNC)
to 1310nm single mode (SC)
[20 km/12.4 mi.] Link Budget: 16.0 dB
S6210-3015
(2) Coax (BNC)
to 1310nm single mode (SC)
[40 km/24.9 mi.] Link Budget: 29.0 dB
S6210-3016
(2) Coax (BNC)
to 1310nm single mode (SC)
[60 km/37.3 mi.] Link Budget: 32.0 dB
S6210-3017
(2) Coax (BNC)
to 1550nm single mode (SC)
[80 km/49.7 mi.] Link Budget: 29.0 dB
S6210-3040
(2) Coax (BNC)
to SFP slot (empty)
Single Fiber Products
Recommended use in pairs
S6210-3029-A1
(2) Coax (BNC)
to 1310nm TX/1550nm RX single fiber
single mode (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
S6210-3029-A2
(2) Coax (BNC)
to 1550nm TX/1310nm RX single fiber
single mode (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
S6210-3029-B1
(2) Coax (BNC)
to 1310nm TX/1550nm RX single fiber
single mode (SC)
[40 km/24.9 mi.] Link Budget: 25.0 dB
S6210-3029-B2
(2) Coax (BNC)
to 1550nm TX/1310nm RX single fiber
single mode (SC)
[40 km/24.9 mi.] Link Budget: 25.0 dB