User Guide

14
SBFTF10xx-10x
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Operation -- Continued
Setting the password:
1. At the prompt, press the letter “P” key.
2. At the prompt, type any alphanumeric combination (8 characters maximum)
3. Press the ENTER key: the password is set.
Important: After setting up or changing command parameter(s) you must save the
change(s) before exiting the screen or the change(s) will not go into effect.
To show the current configuration:
1. At the prompt, press the letter “D” key.
2. Press the ENTER key and the current configuration will appear as shown
below:
---- Local Device ---- SN: 676.
Mode: Software
Ethernet: AutoNeg, 100Mbs, HD, LPT
T1/E1 #1: DSX-1 0-133, Xmit AIS, AMI,
T1/E1 #2: DSX-1 0-133, Xmit AIS,
T1/E1 #3: DSX-1 0-133, Xmit AIS, AMI,
T1/E1 #4: DSX-1 0-133, Xmit AIS,
Serial : 9600, No Parity
DMI: Not Detected. VLAN: Disabled
---- Remote Device ---- SN: 676.
Mode: Software
Ethernet: AutoNeg, 100Mbs, FD, LPT
T1/E1 #1: DSX-1 0-133, Xmit AIS,
T1/E1 #2: DSX-1 0-133, Xmit AIS,
T1/E1 #3: DSX-1 0-133, Xmit AIS,
T1/E1 #4: DSX-1 0-133, Xmit AIS,
Serial : 9600, No Parity
DMI: Not Detected.
->
15
[e-mail] -- Click the “Transition Now” link for a live Web chat.
Operation -- Continued
To show the configuration menu for the local device:
1. At the prompt, type the letter “C,” press the spacebar, then type the letter “L.”
2. Press the ENTER key and the local device configuration menu will appear as
shown below:
Note: In this menu, the T1/E1/J1 commands for local loopback, for example, type
the command this way: LL
, press the spacebar, then type
the port
number, press spacebar, then type the
number
of the command, in this case (1= enable or 2 = disable).
The command sequence IS NOT case sensitive.
Local Device Configuration Menu:
*T1/E1/J1:
LL x 1 - Local Loopback on T1/E1/J1 Port x ENABLE
LL x 2 - Local Loopback on T1/E1/J1 Port x DISABLE
RL x 1 - Remote Loopback on T1/E1/J1 Port x ENABLE
RL x 2 - Remote Loopback on T1/E1/J1 Port x DISABLE
XE x - Enable Transmit AIS on LOS for Port x
XD x - Disable Transmit AIS on LOS for Port x
EB x - Encoding set to B8ZS on Port x
EA x - Encoding set to AMI on Port x
*RS-232:
B x - Serial port baud rate
(1=9600, 2=19200, 3=36400, 4=57600)
*Enet 10/100:
A1 - Autonegotiation ENABLE
A2 - Autonegotiation DISABLE
TLPT1 - Transparent Link Pass Through ENABLE
TLPT2 - Transparent Link Pass Through DISABLE
F10 - Force 10Mbps
F100 - Force 100Mbps
FF - Force Full Duplex
FH - Force Half Duplex
S - Save new Configuration and Exit
Q - Exit without saving Configuration
->