User Guide
Table Of Contents
- Contents
- Contents
- Introduction to the Mercury6e- Transcore Module
- Functionality of the Embedded Modules
- Overview of the Communication Protocol
- Command Set
- Boot Loader Commands
- Multi-Protocol Tag Commands
- Allegro/Title-21 Tag Commands
- eGo/SeGo Tag Command Set
- ATA Tag Command Set
- Gen2 Tag Commands
- Get Configuration Commands
- Get Hardware Version (10h)
- Get Antenna Configuration (61h)
- Get Read TX Power (62h)
- Get Current Tag Protocol (63h)
- Get Write TX Power (64h)
- Get Frequency Hop Table (65h)
- Get User GPIO Inputs (66h)
- Get Current Region (67h)
- Get Power Mode (68h)
- Get User Mode (69h)
- Get Reader Configuration(6Ah)
- Get Protocol Configuration (6Bh)
- Get Reader Statistics (6Ch)
- Get Available Protocols (70h)
- Get Available Regions (71h)
- Get Current Temperature (72h)
- Set Configuration Commands
- Regulatory Test Commands
- Appendix A: Hardware Details
- Appendix B: Using the ArbSer Application
- Appendix C: Error Messages
- Common Error Messages
- FAULT_MSG_WRONG_NUMBER_OF_DATA – (100h)
- FAULT_INVALID_OPCODE – (101h)
- FAULT_UNIMPLEMENTED_OPCODE – 102h
- FAULT_MSG_POWER_TOO_HIGH – 103h
- FAULT_MSG_INVALID_FREQ_RECEIVED (104h)
- FAULT_MSG_INVALID_PARAMETER_VALUE - (105h)
- FAULT_MSG_POWER_TOO_LOW - (106h)
- FAULT_UNIMPLEMENTED_FEATURE - (109h)
- FAULT_INVALID_BAUD_RATE - (10Ah)
- Bootloader Faults
- FPGA Faults
- Flash Faults
- Protocol Faults
- FAULT_NO_TAGS_FOUND – (400h)
- FAULT_NO_PROTOCOL_DEFINED – 401h
- FAULT_INVALID_PROTOCOL_SPECIFIED – 402h
- FAULT_WRITE_PASSED_LOCK_FAILED – 403h
- FAULT_PROTOCOL_NO_DATA_READ – 404h
- FAULT_AFE_NOT_ON – 405h
- FAULT_PROTOCOL_WRITE_FAILED – 406h
- FAULT_NOT_IMPLEMENTED_FOR_THIS_PROTOCOL – 407h
- FAULT_PROTOCOL_INVALID_WRITE_DATA – 408h
- FAULT_PROTOCOL_INVALID_ADDRESS – 409h
- FAULT_GENERAL_TAG_ERROR – 40Ah
- FAULT_DATA_TOO_LARGE – 40Bh
- FAULT_PROTOCOL_INVALID_KILL_PASSWORD – 40Ch
- FAULT_PROTOCOL_KILL_FAILED - 40Eh
- FAULT_PROTOCOL_BIT_DECODING_FAILED - 40Fh
- FAULT_PROTOCOL_INVALID_EPC – 410h
- FAULT_PROTOCOL_INVALID_NUM_DATA – 411h
- FAULT_GEN2 PROTOCOL_OTHER_ERROR - 420h
- FAULT_GEN2_PROTOCOL_MEMORY_OVERRUN_BAD_PC - 423h
- FAULT_GEN2 PROTOCOL_MEMORY_LOCKED - 424h
- FAULT_GEN2 PROTOCOL_INSUFFICIENT_POWER - 42Bh
- FAULT_GEN2 PROTOCOL_NON_SPECIFIC_ERROR - 42Fh
- FAULT_GEN2 PROTOCOL_UNKNOWN_ERROR - 430h
- Analog Hardware Abstraction Layer Faults
- Tag ID Buffer Faults
- System Errors
- Common Error Messages
- Appendix D: FPGA Support
6
Basic Tag Inventory 111
Tag Inventory with Select 113
Tag Inventory With Embedded Operations 114
Write Tag EPC (23h) .................................................................116
Write Tag Data (24h) .................................................................117
Lock Tag (25h) ......................................................................120
Kill Tag (26h) ........................................................................121
Read Tag Data (28h) .................................................................122
Get Tag Data 124
Get Tag Data and Meta Data 124
Get Tag Buffer (29h) .................................................................127
Clear Tag Buffer (2Ah) ................................................................127
Gen2 Tag Specific (2Dh)..............................................................127
Alien Higgs Silicon (Chip Type=0x01) 127
NXP Silicon (Chip Type=0x02) 131
Erase Block Tag Specific (2Eh) .........................................................136
Get Configuration Commands .......................................................137
Get Hardware Version (10h) ...........................................................138
Get Antenna Configuration (61h) .......................................................139
Get Read TX Power (62h) .............................................................140
Get Current Tag Protocol (63h) ........................................................140
Get Write TX Power (64h).............................................................142
Get Frequency Hop Table (65h) ........................................................142
Get User GPIO Inputs (66h) ...........................................................143
Get Current Region (67h) .............................................................143
Get Power Mode (68h) ...............................................................144
Get User Mode (69h) .................................................................145
Get Reader Configuration(6Ah) ........................................................146
Get Protocol Configuration (6Bh) .......................................................146
Get Reader Statistics (6Ch) ...........................................................147
Get Available Protocols (70h) ..........................................................150
Get Available Regions (71h) ...........................................................150
Get Current Temperature (72h).........................................................151
Set Configuration Commands .......................................................152
Set Antenna Port (91h) ...............................................................153
Set Read TX Power (92h) .............................................................153
Set Current Tag Protocol (93h).........................................................154
Set Write TX Power (94h) .............................................................154
Set Frequency Hop Table (95h) ........................................................154
Set User GPIO Outputs (96h) ..........................................................155