SATA III 2260 M.2 SSD MTS600I Datasheet Products Product Description TS32GMTS600I M.2 2260 SSD, SATA3 B+M Key, MLC, Wide Temp. Datasheet version 1.1 No.70, Xingzhong Rd., Neihu Dist.,Taipei City 114, Taiwan, R.O.C. Tel:+886-2-2792-8000 Fax:+886-2-2792-1614 www.transcend-info.com Copyright© Transcend Information, Inc. All Rights Reserved.
Revision History Revision No. History Released Date Editor by 1.0 First version (WD 15nm) 2019/12/31 TSD 1.1 Vibration Format Updated Add 2.6 Recommended Measurement Point Revise 5.2.
Transcend MTS600I Features Part Name Capacity TS32GMTS600I 32GB FEATURES SATA 6Gbps 2D MLC NAND Flash Wide-temperature operation M.2 SATA 2260 B+M Key DDR3 DRAM cache Global wear-leveling function UBER DWPD MTBF Data Retention Warranty 10-15 2.
Table of Content 1 Introduction……………….…..………………………………………………..…………………………..………..……… 5 1.1 General Feature Information……………………………………………………………….………………. 5 1.2 Product List……………………………..……………..………………………………………………..……………5 1.3 Ordering Information……………..……..………………..…………………………………………….………6 2 Product Specifications………………………………………………….……………..……………………………….. 7 2.1 Interface and Compliance……………………………………………………………………….…….……7 2.2 Drive Capacity…………………………………..………………………………………………………….…..…7 2.3 System Performance……………..
1. Introduction 1.1 General Feature Information Hardware Feature - SATA 6Gbps - Transcend Controller TS6500 - 2D MLC NAND Flash - Temperature operation from -40°C to 85°C - M.2 SATA 2260 B+M Key Embedded DDR3 DRAM cache Power shield function AES-256 function (Optional) Firmware Feature - Global wear-leveling function - Enhance Bad block management function - BCH ECC(Error Correction Code) function - TRIM Command function - Advanced Garbage Collection function - StaticDataRefresh function - S.M.A.R.T.
1.3 Ordering Information TSXXXGMTS600I 1 2 3 4 1 – Transcend 2 – SSD Density 3 – G: Gigabyte; T: Terabyte 4 – M.
2. Product Specifications 2.1 Interface and Compliance - SATA3, compatible to SATA2 and SATA1 Compatible with ATA/ATAPI-7 Standard Native Command Queuing(NCQ) Command Set RoHS Compliance CE, FCC and BSMI Compliance 2.2 Drive Capacity [Table 1] User Capacity and Addressable Sectors 32GB User-Addressable Sectors 62,533,296 Byte per Sector 512 Byte 2.
2.4 Supply Voltage [Table 4] Supply Voltage Item Requirements 3.3V±5% Allowable voltage Allowable noise / ripple 100 mV p-p or less 2.5 System Power Consumption [Table 5] Power Consumption Read / Write Active Write (Max.) 32GB 1) 0.84W Active Read (Max.)1) 0.85W Idle 0.3W DEVSLP 5mW Note: 1) The power consumption is measured under SSD operation at maximum performance. The value is affected by system operation performance and workload. 2.
2.7 System Reliability [Table 7] Telcordia SR332 issue 4 MTBF Specifications Parameter 32GB MTBF 2,500,000 hours Note: 1) The calculation is based on 25°C. [Table 8] UBER Specifications Parameter 32GB UBER 10-15 Note: 1) Uncorrectable Bit Error Rate (UBER) is a metric for the rate of occurrence of data errors, equal to the number of data errors per bits read as specified in the JESD218 document of JEDEC standard. For the client application, JEDEC recommends that UBER -15 shall be below 10 .
[Table 13] Warranty Parameter Warranty 32GB 3 years limited [Table 14] Regulations Parameter 32GB Compliance CE, FCC and BSMI 11
3. Mechanical Specification The figure below illustrates the Transcend M.2 Type 2260-D2-B-M Solid State Drive. [Table 15] Physical Dimensions and Weight Model Height (mm) 32GB Max 3.58 12 Width (mm) 22.00±0.15 Length (mm) 60.00±0.
4. Pin Assignments 4.1 Pin Assignments [Table 16] Pin Assignments Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name 01 CONFIG_31) 02 3.3V 39 GND 40 NC 03 GND 04 3.
5. Block Diagram and Function Explanations 5.1 Block Diagram 5.2 Function Explanations 5.2.1 Global Wear Leveling Function Global wear leveling ensures that every block has an even erase count. This helps to extend the life expectancy of an SSD. There are three main processes in global wear leveling: (1) Record the block erase count and save this in the wear-leveling table. (2) Find the static-block and save this in the wear-leveling pointer.
5.2.4 StaticDataRefresh Technology Normally, ECC engine corrections take place without affecting the normal operations of the host. As time passes by, the number of error bits, accumulated in the read transaction, exceeds the correcting capability of the ECC engine and causes corrupted data to be sent to the host. In order to prevent such occurrence, the controller monitors the error bit levels at each read operation.
5.2.8 TCG-Opal Function(Optional) Opal is a comprehensive set of guidelines. The target audience includes manufacturers of storage devices, software vendors, system integrators, and academia. These specifications cover the manufacturing of storage devices, system setup, management, and use; they allow password protection and hierarchical storage management, while preventing data from being stolen or tampered with.
6. Technology Term Explanations 6.1 TBW Terabytes Written (TBW) directly measures how much you can write cumulatively into the drive over its lifetime. Essentially, it just includes the multiplication conducted above in the measurement itself. For example, if your drive is rated for 365 TBW, that means you can write 365 TB into it before a replacement is required. If its warranty period is 5 years, that works out to 365 TB ÷ (5 years × 365 days/year) = 200 GB of writes per day.
7. Installation Requirements 7.1 Card Insertion Angles insertion is allowable and preferred; the intention is to minimize the insertion/extraction force. Minimum of angle of insertion is 5° Minimum two step insertion is desirable; the intention is to minimize the insertion/extraction force.
8. Command Descriptions 8.1 Support ATA Commands This table and the following paragraphs summarize the ATA command set.
SMART Enable/Disable Autosave B0h Non-data SMART Enable Operations B0h Non-data SMART Execute Off-Line Immediate B0h Non-data SMART Read LOG B0h PIO data-In SMART Read Data B0h PIO data-In SMART Read THRESHOLD B0h PIO data-In SMART Return Status B0h Non-data SMART SAVE ATTRIBUTE VALUES B0h Non-data SMART WRITE LOG B0h PIO data-out Read Native Max Address F8h Non-data Set Max Address F9h Non-data Set Max Set Password F9h PIO data-out Set Max Lock F9h Non-data Set Max Fr
8.
8.3 SMART Attributes The following table shows the vendor specific data in byte 2 to 361 of 512-byte SMART data.
9. Contact Information TAIWAN JAPAN No.70, XingZhong Rd., NeiHu Dist., Taipei, Taiwan, R.O.C TEL +886-2-2792-8000 Fax +886-2-2793-2222 E-mail: sales-tw@transcend-info.com E-mail: sales-jp@transcend-info.com Shanghai GERMANY E-mail: sales-cn@transcendchina.com TEL: +86-21-6161-9388 E-mail: sales-de@transcend-info.com TEL: +49-40-538-907-0 Beijing NETHERLANDS E-mail: sales-cn@transcendchina.com E-mail: sales-nl@transcend-info.
