User Manual

Trango Broadband Wireless — User Manual M900S Rev. A Draft
Page 37
configuration section
save <sudb> write downloaded su dbase into flash memory after
unpacking
Both On/Off
set apid <ap-id> set ap id, <ap-id> = 1..255 Both Off
set baseid <base-id> set base station id, <base-id> = 1..9999 Both Off
set defaultopmode <on | off> set default opmode Both On/Off default opmode is off, 0
= 30 sec
set httpport [<port #>] set or display HTTPD port number
port # = 1..65534
Both On/Off default = 80
set snmpcomm <read | write | trap id#
|trap all>
set SNMP read or write or trap community string Both On/Off
set snmpsample <min, 1..60> set SNMP sample period Both On/Off
set telnetport [<port #>] specify telnet port, <port #> = 1..65534 Both On/Off default = 23
ssrssi <ch #> <v | h> display rssi on the current channel Both On/Off
sudb add <suid> <pr|re> <mac> Add new su to sudb AP On/Off
sudb cirmir <<suid>|all> <cir dn> <cir
up> <mir dn> <mir up>
Change su’s cir mir setting AP On/Off
sudb defaultcirmir <default cir dn>
<default cir up> <default mir dn>
<default mir up>
set MIR/CIR values to default values AP On/Off all setting values will be
3000Kbps
sudb delete <<suid>|all> Delete su in sudb AP On/Off
sudb dload unpack the su entries dowloaded from tftp and store
them to su dbase
AP On/Off
sudb gid <suid>|all> <0..15> Change su’s group id AP On/Off
sudb view Display all sudb AP On/Off
survey <search time, sec> <antenna,
h | v | e>
spectrum analysis pf the entire band Both Off
sw display current sw setting Both On/Off
sw 0 [on | off] set sw #0 - packet filter for broadcast/multicast Both On/Off default = on
need to update flash
sw 1 [on | off] set sw #1 – su’s scan ap (su only) SU On/Off default = on
need to update flash
sw 2 [on | off] set sw #2 – su’s TCP/IP service for ap SU On/Off default = off
need to update flash
sw 3 [on | off] set sw #3 – SU to SU service AP On/Off default = off
need to update flash
sw 5 [on | off]* set sw #5 - httpd enable / disable Both On/Off default = on
need to update flash
sw 6 [on | off]* set sw #6 - tcp/ip service for ethernet port (su only) SU On/Off default = off
need to update flash
sw 7 [on | off] set sw #7 - tcp/ip service for su AP On/Off default = off
need to update flash
sysinfo display system configuration Both On/Off
temp display current temperature Both On/Off
tftpd <on | off> enable or disable tftpd service Both On/Off
time display current time Both On/Off
tm display current time mark Both On/Off
updateflash <mainimage | fpgaimage>
<* | <current chscksum>> <* | <new
checksum>>
get image from tftp buffer, verify checksum and write
to flash memory at main or fpga image section.
*: skip checksum verification
Both On/Off
updateflash [systemsetting | ss] write current configuration into flash memory at system
configuration section
Both On/Off
updateflash sudb> write downloaded su dbase into flash memory after
unpacking
AP On/Off
ver display
1. version number and date code
2. firmware and fpga version code
Both On/Off