Installation and Maintenance Manual
Installation Mechanical
22 RTAE-SVX001B-EN
Extended Length Unit
(a)
150S 1553 704 1795 814 1974 895 1959 889 2088 947 1804 818 --------
165S 1344 610 1236 561 1537 697 1494 678 1686 765 1668 757 1636 742 1570 712 ----
150 1563 709 1621 735 1705 773 1875 850 1952 885 1575 714 1601 726 1601 726 ----
165 1776 806 1827 829 1956 887 1925 873 2058 933 1958 888 1517 688 1515 687 ----
180 1774 805 1822 827 1990 903 1975 896 2128 965 2030 921 1577 715 1557 706 ----
200 1706 774 1524 691 1662 754 1294 587 1938 879 1738 788 1267 575 1753 795 1457 661 1652 749
225 1857 842 1669 757 1844 836 1412 640 2156 978 1860 844 1378 625 1985 900 1501 681 1766 801
250 1852 840 1664 755 1885 855 1439 653 2219 1006 1936 878 1438 652 2046 928 1530 694 1795 814
275 1874 850 1860 844 1626 737 1700 771 2204 1000 2101 953 2017 915 2131 967 1820 826 1642 745
300 1946 883 1826 828 1854 841 1795 814 2143 972 2106 955 2408 1092 2338 1060 1808 820 1898 861
(a) Units are extended length if either of the following are selected:
Low Harmonic Distortion Option (model number digit 29 = 1)
Autotransformer (model number digit 28 = 1 or 2)
Units without Low Harmonic Distortion Option or Autotransformer (digits 28, 29 = X0) are standard length.
Table 11. Point weights (continued)
Location
12345678910
Tons lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg
Table 12. Isolator locations
(a)
Location
12345678910
Tons in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm
Standard Length
150S 23.6 600 27.6 700 102.4 2600 94.5 2400 187.0 4750 187.0 4750 --------
165S 15.7 400 23.0 585 98.4 2500 102.2 2595 196.9 5000 204.7 5200 --------
150 24.4 620 11.8 300 47.2 1200 82.7 2100 100.4 2550 153.5 3900 188.2 4780 188.2 4780 ----
165 17.7 450 23.0 585 98.6 2505 102.2 2595 155.5 3950 190.6 4840 242.1 6150 242.9 6170 ----
180 17.7 450 23.0 585 98.6 2505 102.2 2595 155.5 3950 190.6 4840 242.1 6150 242.9 6170 ----
200 23.6 600 23.6 600 102.4 2600 137.8 3500 155.5 3950 198.8 5050 255.9 6500 263.8 6700 ----
225 23.6 600 23.6 600 102.4 2600 137.8 3500 155.5 3950 198.8 5050 255.9 6500 263.8 6700 ----
250 23.6 600 23.6 600 102.4 2600 137.8 3500 155.5 3950 198.8 5050 255.9 6500 263.8 6700 ----
275 21.7 550 18.9 480 141.3 3590 125.2 3180 196.1 4980 236.2 6000 236.2 6000 259.8 6598 328.0 8330 324.4 8240
300 19.7 500 27.6 700 143.1 3634 143.1 3634 202.4 5142 235.6 5984 257.9 6551 296.6 7534 347.8 8834 339.5 8624
Extended Length Unit
(b)
150S 19.7 500 15.7 400 102.4 2600 133.9 3400 204.7 5200 208.7 5300 --------
165S 23.6 600 23.6 600 86.6 2200 78.7 2000 149.6 3800 157.5 4000 259.8 6600 259.8 6600 ----
150 25.0 635 23.6 600 84.6 2150 98.4 2500 147.6 3750 190.9 4850 240.2 6100 240.2 6100 ----
165 19.7 500 19.7 500 129.9 3300 129.9 3300 204.7 5200 234.3 5950 293.3 7450 299.2 7600 ----
180 19.7 500 19.7 500 129.9 3300 129.9 3300 204.7 5200 234.3 5950 293.3 7450 299.2 7600 ----
200 25.6 650 19.7 500 118.1 3000 98.4 2500 208.7 5300 196.9 5000 255.9 6500 255.9 6500 315.0 8000 315.0 8000
225 25.6 650 19.7 500 118.1 3000 98.4 2500 208.7 5300 196.9 5000 255.9 6500 255.9 6500 315.0 8000 315.0 8000
250 25.6 650 19.7 500 118.1 3000 98.4 2500 208.7 5300 196.9 5000 255.9 6500 255.9 6500 315.0 8000 315.0 8000
275 6.3 160 9.8 250 177.2 4500 139.8 3550 198.8 5050 242.1 6150 309.1 7850 313.0 7950 354.3 9000 370.1 9400
300 9.8 250 9.8 250 177.2 4500 139.8 3550 206.7 5250 242.1 6150 311.8 7920 313.4 7960 393.7 10000 393.7 10000
(a) Dimensions are referenced from end of frame on the control panel side.
(b) Units are extended length if either of the following are selected:
Low Harmonic Distortion Option (model number digit 29 = 1)
Autotransformer (model number digit 28 = 1 or 2)
Units without Low Harmonic Distortion Option or Autotransformer (digits 28, 29 = X0) are standard length.