The most advanced trailer dolly on the planet Operating Manual WARNING Carefully read and understand all the instructions before connecting your new Trailer Valet. Failure to follow these guidelines may result in serious injury to persons and property for which Trailer Valet will not be held liable. Do not allow persons to operate or assemble this trailer dolly until they have read this manual and have developed a thorough understanding of how the trailer dolly works.
Congratulations on your purchase of the Trailer Valet. For your future reference please complete the owner’s record below: Purchase Date: ______________________Order No.:______________________ Retailer:_____________________________ Be sure to save your receipt and owner’s manual with warranty information in a safe place. The Trailer Valet is made of high strength steel and given a powder coat finish made to resist corrosion from the elements and marine use.
DO NOT use the Trailer Valet on slopes and inclines beyond stated limits. DO NOT attempt to use the Trailer Valet to pull up (nose first) or to push down (rear first) an incline. Always move along an incline with the unit on the lower end of the incline. DO NOT use your drill on the Trailer Valet’s high gear. Carefully read all instructions.
Upon removing items from packaging, it is very important to thoroughly inspect all parts of the system before using the device. Any part that is missing or damaged must be immediately replaced. Contact Trailer Valet Customer Service at 1-844-846-9344 or Support@TrailerValet.com What’s in the Box: A. The Trailer Valet 1. Axle Yoke Compartment 2. Rotating Coupler 3. Brake Cap 4. Drive/Crank Handle 5. Steering/Brake Handle 6. Side Plates 7. Gear Covers 8. Low Gear Driveshaft 9. High Gear Driveshaft 10.
Step 1: SETUP Remove all the items from the box. If the Coupling Plate is not already installed with the Ball Base, detach the ball from the Locking Nut, slip the Coupling Plate under the ball, and reinsert into the Locking Nut. Secure tightly. ALTERNATIVE METHOD FOR INSTALLING THE BALL ATTACHMENT: NOTE: This method is recommended for heavier trailers and users who have difficulty securing the ball tightly into the coupler. I.
Knowing the proper techniques to operate your Trailer Valet can help keep you and others around you safe. In this guide, you are shown the basic fundamentals for effective operations. However, it is up to you to analyze the situation and make the decisions necessary for the proper use of your Trailer Valet. Apply your knowledge of your Trailer Valet and the basic fundamentals you have practiced to adjust your techniques to each unique situation.
Step 6: OPERATING THE DEVICE NOTE: If your trailer has built-in brakes, they must be disengaged prior to operation of the Trailer Valet. Consult your trailer manufacturer’s manual/instructions on temporary brake release. If this is not available to you, please contact Trailer Valet Customer Support through phone or email for assistance. 1) When you’re getting ready to operate the device, make sure you have one hand firmly gripped on the brake, and the other hand firmly gripped on the drill/driver.
SuperTech S Corp warrants for one year from the purchase date that the product will be in working condition and will be free from manufacturing defects, provided that installation and use of the product is in accordance with product instructions. This warranty is only made to the original consumer purchaser and is non-transferable. ALL OTHER WARRANTIES IMPLIED OR EXPRESSED ARE HEREBY DISCLAIMED. This warranty does not cover: 1. Normal wear and tear or normal aging of the product; 2.
Check Before First Use Before Each Use Every 90 Days Take the time to read and understand these operating instructions in order to understand your Trailer Valet and its operations. Read and understand your drill/driver operator’s manual and instructions. Inspect the Trailer Valet for damage. Replace any damaged parts immediately. If a part must be replaced, contact Trailer Valet Customer Service.
10
Copyright 2017 by Supertech S. Corporation. All right reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Supertech S. Corporation. For further information or if you have any questions, please contact: SUPERTECH S. CORP. 2368 Peck Road Industry, CA 90601 Customer Service: (844) 846-9344 Email: support@trailervalet.com Or visit: www.trailervalet.
