Data Sheet

ManualsBrandsTracoPower ManualsActive ComponentsTracoPower TEL 10-2413WI DC/DC converter (print) 24 V DC 666 mA 10 W No. of outputs: 1 x

www.tracopower.com Page 1 of 4

DC/DC Converter TEL 10WI Series, 10 Watt

Models

The TEL 10WI series is a range of isolated 10 Watt converters which come in a ultra com-

pact DIP-16 metal package. The design purpose of these series was to miniaturized low

power DC/DC converters to the maximum without sacriﬁng high efﬁcency. The TEL 10WI

series sets the new standart for power density with 3.83 W/cm

The TEL 10WI series offer an ultra wide 4:1 input voltage range and feature a high ef-

ﬁciency of up to 86% which enables an operation temperature of up to +70°C at full load

and up to 88°C with 50% load.

The converters have an internal input ﬁlter to comply with conducted emission EN 55032

/ EN 55022 class A. The TEL 10WI Series models are an economical solution for space

critical and cost sensitive applications in instrumentation, IT and industrial electronics.

Order code Input voltage Output voltage Output current max. Efﬁciency typ.

TEL 10-2410WI

3.3 VDC 2700 mA 80 %

TEL 10-2411WI

5.1 VDC 2000 mA 83 %

TEL 10-2412WI 9 - 36 VDC

12 VDC 833 mA 87 %

TEL 10-2413WI (nominal 24 VDC)

15 VDC 666 mA 88 %

TEL 10-2415WI

24 VDC 416 mA 88 %

TEL 10-2422WI

±12 VDC ±416 mA 87 %

TEL 10-2423WI

±15 VDC ±333 mA 87 %

TEL 10-4810WI

3.3 VDC 2700 mA 80 %

TEL 10-4811WI

5.1 VDC 2000 mA 83 %

TEL 10-4812WI 18 - 75 VDC

12 VDC 833 mA 87 %

TEL 10-4813WI (nominal 48 VDC)

15 VDC 666 mA 88 %

TEL 10-4815WI

24 VDC 416 mA 88 %

TEL 10-4822WI

±12 VDC ±416 mA 87 %

TEL 10-4823WI

±15 VDC ±333 mA 87 %

Models

• Most compact 10 Watt converter in

DIP-16 metal casing

• Highest power density of 3.83 W/cm

• 6-side shielded metal case with

insulated base plate

• Ultra wide 4:1 input voltage range

• High efﬁciency for low thermal loss

• Operating temperature range of

-40°C to +88°C

• Built-in EN 55032 class A ﬁlter

• Current limitation and protection

against short circuit

• 3 years product warranty

UL 62368-1

UL 60950 -1

Summary of content (4 pages)

PAGE 1
DC/DC Converter TEL 10WI Series, 10 Watt • Most compact 10 Watt converter in DIP-16 metal casing • Highest power density of 3.
PAGE 2
TEL 10WI Series, 10 Watt Input Specifications Input current at no load 24 Vin models: 10 mA typ. 48 Vin models: 7 mA typ. Surge voltage (1 s max.) 24 Vin models: 50 V max. 48 Vin models: 100 V max. Start up voltage 24 Vin models: 9 V (or lower) 48 Vin models: 18 V (or lower) Under voltage shut down 24 Vin models: 8 V typ. / 7 V min. 48 Vin models: 16 V typ. / 15 V min.
PAGE 3
TEL 10WI Series, 10 Watt General Specifications Temperature ranges – Operating (natural convection: 20 LFM, 0.1 m/s) 3.3 & 5.1 Vout models: –40°C to +80°C other output models: –40°C to +88°C – Case temperature +105°C max. – Storage temperature –55°C to +125°C Derating 3.3 & 5.1 Vout models: 2.0 %/K above 55°C other output models: 2.8 %/K above 70°C Humidity (non condensing) 95 % rel H max.
PAGE 4
TEL 10WI Series, 10 Watt Outline Dimensions Pin-Out 10.16 (0.40) bottom view 16 3.0 (0.12) 10 15.24 (0.60) 9 2.54 (0.1) Pin Single Dual 1 –Vin (GND) –Vin (GND) 7 NC NC 8 NC Common 9 +Vout +Vout 10 –Vout –Vout 16 +Vin (Vcc) +Vin (Vcc) NC: not connected Dimensions in mm, () = Inch Tolerances: x.x ±0.5 (±0.02) x.xx ±0.25 (±0.01) Pin diameter 0.5 ±0.05 (0.02 ±0.002) 3.8 (0.15) 8.0 (0.31) 23.8 (0.94) 13.7 (0.54) 8 7 1.77 (0.07) 1 ø 0.5 (0.