GPS-TRACKER / RASTREADOR GPS / TRACEUR GPS / LOCALIZZATORE GPS EN - Operating instructions Product Name: GPS Tracker Model Name: TRKM010 Manufacture: Trackimo INC.
Pack contents / product parts.............................................................25 General information..............................................................................26 Key to symbols............................................................................................26 Proper use..........................................................................................28 Safety..................................................................................................
Pack contents / product parts 1 On/off SOS Reset button 2 G_ sensor 3 Magnetic charging port 4 Red light 5 Blue light 6 Green light
General information These operating instructions are for the TrackimoTravelCAT M1 GPS Tracker,which will simply be referred to as ‘tracker’ in the following. They contain important information regarding set-up and operation. Before using the tracker, please read the operating instructions carefully. This particularly applies to the safety notes. Failure to adhere to these operating instructions may result in severe injury or damage to the tracker.
The FCC logo indicates electronic devices that conform with FCC provisions from the American authority, the FederalCommunications Commission. The symbol also guarantees compatibility with standards, suchas those set out by the International Organization for Standardization (abbreviated as ISO).
Proper use The tracker is suitable for locating an item or living being. Only use the tracker as described in these operating instructions.Any other use is deemed improper and may result in damage to property or even personal injury. The tracker is not a children’stoy. The manufacturer and vendor do not accept any liability for damage caused by improper or incorrect use.
− − − − If the charging cable is damaged, it must be replaced by the manufacturer, the manufacturer’s service department or a similarly qualified person in order to avoid risk. Only charge the battery with the charging cable supplied. Do not open the tracker casing. Instead, ensure any repairs are carried out by specialists. Contact a specialist workshop.
WARNING! Explosion and fire hazard! Improperuse of the batteryincreases the risk of explosion and fire. − Protect the tracker from mechanical damage. − Do not expose the battery to excessive heat such as direct sunlight, fire, etc.The ambient air temperature should not exceed 60 °C or fall below -20 °C. − Only use original accessories for charging. − Always store the tracker in a dry space at the right temperature. − Do not try to remove the battery from the tracker using spikes or sharp objects.
− WARNING! Dangers to children and persons with reduced physical, sensory ormental abilities (for example partially disabled people, older persons with limitations to physical or mental abilities) or those with less experience and knowledge (for example older children). The tracker is not a children’s toy. If you give your child the tracker to take with them, you must comprehensively explain the dangers to them and explain how to operate the tracker.
Initial set-up Checking the pack contents NOTE Risk of damage! Installing and charging the battery When you unpack the tracker for the first time, the battery is empty. Charge it as follows: If you carelessly open the packaging 1. Connect the charging plug of the with a sharp knife or another sharp charging cable to the tracker with object, the tracker can quickly the magnetic chargingport. become damaged. 2.
Turning the tracker on 1. Take the tracker outside so that it is in the open air. 2. Press and hold the on/off button for at least 3 seconds. The green light on the front will start to flash. 3. Put the tracker down and wait for at least 15minutes. The trackerwill carry out initial GPS positioning. This is required for the device to function correctly. The tracker will then be ready for use and can be activated. Activating the tracker 1. Open your Internet browser and go to the following website: www.
Functions Button functions On/off button: Checking the Press and hold the on/off button connection Press the on/off button to check whether the tracker is on or off. If at least one light comes on, the tracker is on. If no light comes on, the tracker is off. Note: You can save battery life by using the OFF setting in your app’s menu or on the tracking interval homepage. The device doesn’t have to be turned off.
A pink rectangular fence will be created around your device’s current location (or in the centre of the map). − − − You can also enter an address to position a fence. You can choose a pre-defined size. You can change the size by making the sides ofthe rectangle bigger or smaller, or by moving the rectangle. 4. Onceyourfence hasbeencreated, you can give your geofence a name and click on “Save”. 5. Now you can enter additional telephone numbers (for SMS notifications) or e-mail addresses for notifications.
3. Set the movement alert function to “On”. Light sensor The tracker has a light sensor. It registers strong light changes such as an abrupt change of light from 5. Click on “Save”. dark to bright. If such a change of Low battery alert light is registered, the tracker will You will receive a notification when automatically send a notification to your registered e-mail address or, the tracker battery level is low. if you have specified a telephone 1.
a building or under a concrete roof. The signal may be blocked or diverted even if the tracker is placed near a window. In such cases the device will use an alternative method to calculate its position. The position is determined through identification of a nearby WiFi router or mobile communications antenna. This is less precise than GPS data, and may be hundreds of metres from the tracker.
Light and sound meanings Action Light Sound Press the on/off button and hold Green light lights up, then blinks twice; the tracker starts up Short beep sound Press the on/off button and hold Green light turns on and red light flashes; the tracker turns off No sound Press the on/off button quickly Green light turns on briefly No sound Connected to the mobile network Blue light turns on for 4 seconds Long beep sound Low battery Red light blinks No sound Battery is charging Red light blinks
Cleaning NOTE Risk of damage! Improper handling of the tracker may result in damage. − Do not use any abrasive cleaning agents, brushes with metal or nylon bristles or any sharp or metallic cleaning materials such as knives, metal scouring pads, etc. These could damage surfaces. − Never submerge the tracker in water and do not use any steam cleaners when cleaning. This can damage the tracker. − Never put the tracker in the washing machine. This would destroy it. 1. Wipe surfaces with a slightly damp cloth.
Technical data Model: TRKM010 Battery: Li-Ion, 600 mAh Input voltage: 5 V / 400 mA Protection class: Operating temperature: –20 to +60 °C Extreme Temp. Tolerance:-30℃ to +60℃ Battery life: form GSM/WCDMA: 2 to 60 days MTK6276 Position location platform GPS: MTK3337 Frequency band: SM :GSM 850/ GSM 900/ DCS 1800/ PCS 1900 Wi-Fi: MT5931 Bluetooth: TI CC2541 BT4.0 Dimensions: 47 ×40×17 mm Weight: approx.
Declaration of Conformity The NDM Network hereby declares that the TRKM010 tracker radio equipment model conforms with EU Directive 2014/53/EU.Thefull textfortheEU Declaration of Conformity can be found on the following webpage: https://trackimo.eu/de/download/ Disposal Disposing of the packaging Dispose of the packaging ensuring that materials are correctly separated. Dispose of cardboard and carton as waste paper and dispose of foils via the recyclable material collection service.
Batteries cannot be disposed of as household waste! As a consumer, you are legally obligated to dispose of all batteries at a municipal/district collection point or at a retailer, regardless of whether or not they contain harmful substances*, so that they can be disposed of in an environmentally friendly way.
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
