Installation Guide TX432 JetStream 10-Gigabit 2-Port SFP+ Module REV1.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
CE Mark Warning This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.
Chapter 1 Introduction 1.1 Overview of the Product JetStream 10-Gigabit 2-Port SFP+ Module TX432 is an interface card providing two 10G SFP+ ports. It is applicable to multiple TP-LINK switch models.
1.2 Description of Ports Ports of TX432 are both 10G SFP+ ports. You can insert an SFP+ transceiver into the port (on TX432) to connect it to the SFP+ port (on another device) through an optical fiber, or an SFP+ cable provided by TP-LINK. For details about the supported SFP+ transceivers and SFP+ cables, please refer to the table below. Transceiver Central /Cable wavelength Connector Interface cable Max transmission distance 50/125μm multimode TXM431-SR 300m optical fiber 850nm 62.
1.3 Description of LEDs There is an LED for each port, labeled as M1 and M2, on the panel of TX432. Described below: LED M1,M2 Status Description Off The port isn’t connected to any devices. On Blinking SPF+ port is connected to a device. SPF+ port is connected to a device and transferring data. )Note: The switch applicable to TX432 will display corresponding LEDs on its front panel to indicate the port status of the interface card. For details about the LEDs, please refer to the switch user guide.
Figure 2-1 Install an interface card (1) 3. Hold the fastening screws on the front panel of the interface card, and gently push the interface card in along the slot guide rail until the interface card is flush with the switch, as shown in Figure 2-2. Figure 2-2 Install an interface card (2) 4. Tighten the captive screws with a Phillips screwdriver to fix the interface card in place. • Removing the Interface Card 1.
2. Use a Phillips screwdriver to loosen the captive screws at both sides of the interface card until all spring pressure is released. 3. Pull the interface card towards you along the guide rails, until it completely comes out of the switch chassis. )Note: • TX432 supports hot plug, so if necessary you can install or remove the interface card when the switch is operating. However, it is recommended that the power be turned off during installation.
Do not look straight at the optical port of TX432 when it is operating, because the optical fiber beam is of high energy and thus will do great harm to the retina. Looking straight at the optical fiber beam could do great harm to your eyes.
Appendix: Specifications Normal Standards Safety & Emissions Max Power Consumption LED Operating Temp Storage Temp Operating Humidity Storage Humidity Dimension IEEE 802.3ae, IEEE 802.3aq, SFF-8431 FCC, CE 6.
Technical Support For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq To download the latest Firmware, Driver, Utility and User Guide, go to: http://www.tp-link.com/en/support/download For all other technical support, please contact us by using the following details: Global Tel: +86 755 2650 4400 Fee: Depending on rate of different carriers, IDD. E-mail: support@tp-link.com Service time: 24hrs, 7 days a week USA/Canada Toll Free: +1 866 225 8139 E-mail: support.usa@tp-link.
