Specifications

ManualsBrandsTP-LINK ManualsNetworkingTX-VG1530

TX-VG1530

N300 Wireless VoIP GPON Router

Rev: 1.0.0

1910010904

Summary of content (135 pages)

PAGE 1
TX-VG1530 N300 Wireless VoIP GPON Router Rev: 1.0.
PAGE 2
COPYRIGHT & TRADEMARKS is a registered trademark of Specifications are subject to change without notice. TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD.
PAGE 3
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 4
Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada.
PAGE 5
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України. Safety Information ● When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. ● Don’t disassemble the product, or make repairs yourself.
PAGE 6
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: N300 Wireless VoIP GPON Router Model No.
PAGE 7
CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Product Overview ................................................................................... 2 1.1 Overview of the GPON router ....................................................................................... 2 1.2 Main Features ............................................................................................................... 3 1.
PAGE 8
4.4.9 IPSec VPN ......................................................................................................................... 35 4.5 DHCP Server .............................................................................................................. 38 4.5.1 DHCP Settings ................................................................................................................... 38 4.5.2 Clients List...................................................................................
PAGE 9
4.10.2 Static Route ...................................................................................................................... 77 4.10.3 RIP Settings ...................................................................................................................... 78 4.11 IPv6 Route Settings .................................................................................................... 79 4.11.1 IPv6 Default Gateway ......................................................................
PAGE 10
4.21.5 SNMP Settings ............................................................................................................... 110 4.21.6 Backup & Restore ........................................................................................................... 111 4.21.7 Factory Defaults.............................................................................................................. 112 4.21.8 Firmware Upgrade .............................................................................
PAGE 11
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Package Contents The following contents should be found in your package:  One TX-VG1530 N300 Wireless VoIP GPON Router  One Power Adapter for TX-VG1530 N300 Wireless VoIP GPON Router  Quick Installation Guide  One RJ45 cable  One Resource CD for TX-VG1530 N300 Wireless VoIP GPON Router, including: • This User Guide • Other Helpful Information  Note: Make sure that the package contains the above items.
PAGE 12
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Chapter 1. Product Overview Thank you for choosing the TX-VG1530 N300 Wireless VoIP GPON Router. 1.1 Overview of the GPON router TP-LINK’s N300 Wireless VoIP GPON Router TX-VG1530 is a next-generation Gigabit Passive Optical Network (GPON) integrated access device (IAD), ideal for Fiber to The Home solution.
PAGE 13
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 1.2 Main Features  All-in-One: High speed GPON ONT, NAT Router, 4-port Switch, Wireless N Access Point and VoIP Gateway in one device provides a one-stop networking solution.  Complies with ITU G.984.1, ITU G.984.2, ITU G.984.3 and ITU G.984.4, providing you comprehensive GPON network compatibility.  Extremely high access speed up to 2.488Gbps Downstream and 1.244Gbps Upstream.
PAGE 14
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The router’s LEDs are located on the front panel (View from left to right). They indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name (Power) (PON) (LOS) (USB) (LAN1-4) (WLAN) Colour Green Green Red Green Green Green Status Indication On The GPON router is powered on. Off The GPON router is off.
PAGE 15
TX-VG1530 N300 Wireless VoIP GPON Router User Guide (WPS) Green （Phone1-2） Green On A wireless device has been successfully added to the network by WPS function. Flash WPS handshaking is in process and will continue for about 2 minutes. Please press the WPS button on other wireless devices that you want to add to the network while the LED is flashing. Off A wireless device has failed to be added to the network by WPS function. Please refer to 4.6.2 WPS Settings for more information.
PAGE 16
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  USB: The USB port connects to a USB storage device or a USB printer.  LAN1, LAN2, LAN3, LAN4: Through these ports, you can connect the Router to your PC or the other Ethernet network devices.  WiFi: The switch for the WiFi function.  RESET: There are two ways to reset the Router's factory defaults. Method one: With the Router powered on, use a pin to press and hold the Reset button for at least 6 seconds.
PAGE 17
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Chapter 2. Connecting the GPON Router 2.1 System Requirements  Broadband Internet Access Service (Fiber).  PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors.  TCP/IP protocol on each PC.  Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. 2.2 Installation Environment Requirements  The Product should not be located where it will be exposed to moisture or excessive heat.
PAGE 18
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Note: The diameter of the screw, 3.6mm
PAGE 19
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 2-2  Note: Only green SC/APC interface suits the OPTICAL port.
PAGE 20
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your TX-VG1530 N300 Wireless VoIP GPON Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default IP address of the TX-VG1530 N300 Wireless VoIP GPON Router is 192.168.1.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for description.
PAGE 21
TX-VG1530 N300 Wireless VoIP GPON Router User Guide You can check it following the steps below: 1) Is the connection between your PC and the router correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254. 3.
PAGE 22
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 2. After your successful login, you will see the Login screen as shown in Figure 3-5. Figure 3-5 3. The GPON router supports SN authentication and CTC authentication, you can select one of them according to your ISP requirement. If SN authentication is required, choose Network→ GPON SN Settings in the main menu, the GPON Configuration screen will appear, enter the GPON Password and GPON SN provided by your ISP and then click Save.
PAGE 23
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 3-6 If CTC authentication is required, choose Network→ GPON CTC Settings in the main menu, the GPON Configuration screen will appear, enter the GPON Username and GPON Password provided by your ISP and then click Save. Figure 3-7 4. Choose Pon→Connect Status in the main menu, the GPON Status screen will appear. Click Refresh to update this page, then check whether the ONU State is registered.
PAGE 24
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 3-8  Note: Once the ONU State in not registered, please the GPON information and try again with the correct settings. Choose Network→ WAN Settings in the main menu, the WAN Interface screen will appear, then click Add to add a new entry. In the next screen you can configure the WAN Settings, then click Save to make your settings take effect.
PAGE 25
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 3-9 The basic settings for your GPON router are completed. Please try to log on to website to test your Internet connection.
PAGE 26
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Chapter 4. Configuring the GPON Router This chapter will show each Web page's key function and the configuration way. 4.1 Login After your successful login, you will see the twenty one main menus on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions. The detailed explanations for each Web page’s key function are listed below. 4.
PAGE 27
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-1 4.3 PON Choose “PON”, there are four submenus under the main menu: Connect Status, Optical Status, Statistics and Advance. The detailed explanations for each submenu are provided below.
PAGE 28
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.3.1 Connect Status Choose “PON”“Connect Status”, the GPON Status screen will appear, click Refresh to update this page, which shows you the current GPON Status. Here we use CTC authentication as an example (shown in Figure 4-2). Figure 4-2  Connection Type: Here shows the type of the current connection.  ONU ID: The ID of the ONU.  ONU Status: The ONU is registered or not.  CTC Authentication: The current status of CTC Authentication.
PAGE 29
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-3 Click Refresh to update this page. 4.3.3 Statistics Choose “PON”“Statistics”, the traffic statistics screen will appear (shown in Figure 4-4), click Refresh to update this page, and then you can view the statistics of the GPON router, including GPON traffic and OMCI traffic of the current Packets Statistic. Figure 4-4  Bytes Sent: The total number of bytes sent by the GPON router.
PAGE 30
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.3.4.1 Forwarding Rules Choose “PON” “Advance”“Forwarding Rules”, and you will see the GPON Forwarding Rules Table in the screen similar to Figure 4-5. Figure 4-5 4.3.4.2 IOT Log Choose “PON” “Advance”“IOT Log”, and you will see the GPON OMCI Debug screen (shown in Figure 4-6). Figure 4-6 Click the Export button to save the GPON OMCI settings as a backup file in your local computer. 4.
PAGE 31
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.4.1 WAN Settings Choose “Network”“WAN Settings”, and you will see the WAN Port Information Table in the screen similar to Figure 4-7, which describes the WAN port settings and the relevant manipulation to each interface. There are four different configurations for the connection types, which are Static IP, Dynamic IP, PPPoE and Bridge. You can select the corresponding types according to your needs.
PAGE 32
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-8 4.4.1.1 Static IP Select this option if your ISP provides static IP information to you. You should set static IP address, IP subnet mask, and gateway address in the screen below.
PAGE 33
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-9 VLAN Configuration:  Enable VLAN: Enable or disable this function. Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same LAN, when in fact they are located on a number of different LAN segments.
PAGE 34
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Default Gateway: select a WAN Interface from the drop-down list as the IPv4 default gateway.  Enable IPv6: Check the box to enable IPv6.  IPv6 Address: Enter the IPv6 address in dotted-decimal notation provided by your ISP.  Prefix length: Enter the length of the prefix  IPv6 Gateway: Enter the gateway IPv6 address in dotted-decimal notation provided by your ISP.
PAGE 35
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-10 Click the Save button to save the settings. 4.4.1.2 Dynamic IP Select this option, the GPON router will be able to obtain IP network information dynamically from a DHCP server provided by your ISP.
PAGE 36
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-11 Click Advanced, advanced selections for WAN Service Setup can be shown.  MTU (bytes): Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1500 Bytes. It is not recommended that you change the default value unless required by your ISP.  Enable NAT: This technology translates the IP addresses of a local area network to a different IP address for the Internet.
PAGE 37
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Get IP Unicast: This is disabled by default. The minority of DHCP Server of ISP will not support to enable this. When the route is connected right but IP cannot get, you can select this box.  Set DNS Server manually: Choose “Set DNS Server manually”, you can set DNS Server manually here. The GPON router will use this DNS Server for priority.  Host Name: Here displays model No. of your GPON router. Click the Save button to save the settings. 4.4.1.
PAGE 38
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Choose the right connection type according to your needs: For PPPoE connection, you can select Connect on demand or Connect automatically or Connect manually. Connect on demand is dependent on the traffic. If there is no traffic (or Idle) for a pre-specified period of time), the connection will tear down automatically. And once there is traffic send or receive, the connection will be automatically on.
PAGE 39
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-13  Note: After you finish the Internet configuration, please click Save to make the settings take effect. 4.4.2 LAN Settings Choose “Network”“LAN Settings” menu, and you will see the LAN screen (shown in Figure 4-14). Please configure the parameters for LAN ports according to the descriptions below. Figure 4-14  IP Address: You can configure the GPON router’s IP Address and Subnet Mask for LAN Interface.
PAGE 40
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Enable IGMP Snooping: If you select the option, please choose the IGMP Mode: Standard Mode or Blocking Mode.  Enable Second IP: You can configure the GPON router’s second IP Address and Subnet Mask for LAN Interface through which you can also access to the Web-based Utility as the default IP Address and Subnet Mask.  DHCP Server: These settings allow you to configure the GPON router‘s Dynamic Host Configuration Protocol (DHCP) server function.
PAGE 41
TX-VG1530 N300 Wireless VoIP GPON Router User Guide If DHCPv6 Server is selected, please complete the following parameters. Figure 4-16  • Start IPv6 Address: Enter a value for the DHCPv6 server to start with when issuing IPv6 addresses. • End IPv6 Address: Enter a value for the DHCPv6 server to end with when issuing IPv6 addresses. • Leased Time: The Leased Time is the amount of time in which a network user will be allowed connection to the GPON router with their current dynamic IPv6 address.
PAGE 42
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.4.4 MAC Clone Choose menu “Network”“MAC Clone”, you can configure the MAC address of the WAN Interface as shown below. The WAN Interface List displays the WAN Interfaces you have configured on the section 4.4.1 WAN Settings, and its default MAC Address. You can select corresponding WAN Interface from the drop-down list and click Clone MAC To button to clone your current PC MAC, and then click Save.
PAGE 43
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  • L2TP Passthrough: Layer Two Tunneling Protocol (L2TP) is the method used to enable Point-to-Point sessions via the Internet on the Layer Two level. To allow L2TP tunnels to pass through the GPON router, click Enable. • IPSec Passthrough: Internet Protocol security (IPSec) is a suite of protocols for ensuring private, secure communications over Internet Protocol (IP) networks, through the use of cryptographic security services.
PAGE 44
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-22 GPON Password  GPON Password: Displays the factory default password.  New Password: Enter the password provided by your ISP. Click Save to make the settings take effect. GPON SN  GPON SN: Displays the factory default SN.  New SN: Enter the SN provided by your ISP. Click Save to make the settings take effect. 4.4.
PAGE 45
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Click the Save button to save your settings. 4.4.9 IPSec VPN Choose “Network”“IPSec VPN”, you can add/remove or enable/disable the IPSec tunnel connections on the screen as shown in Figure 4-24. Figure 4-24 This section will guide you to configure a VPN tunnel between two TX-VG1530s. The topology is as follows.  Note: You could also use other VPN Routers to set VPN tunnels with TX-VG1530. TX-VG1530 supports up to 10 VPN tunnels simultaneously.
PAGE 46
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-25  IPSec Connection Name: Enter a name for your VPN.  Remote IPSec Gateway Address (URL): Enter the destination gateway IP address in the box which is the public WAN IP or Domain Name of the remote VPN server endpoint. (For example: Input 219.134.112.247 in Device1, Input 219.134.112.
PAGE 47
TX-VG1530 N300 Wireless VoIP GPON Router User Guide After complete the basic settings and click Save/Apply in both Device1 and Device2, PCs in LAN1 could communicate with PCs in remote LAN2. (For example: You can ping the IP address of PC2 which is 192.168.2.100 in PC1)  Note: The VPN Servers Endpoint from both ends must use the same pre-shared keys and Perfect Forward Secrecy settings. Click Show Advanced Settings and then you can configure the Advanced Settings.
PAGE 48
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Note: If you want to change the default settings of Advanced Settings, please make sure that both VPN server endpoints use the same Encryption Algorithm, Integrity Algorithm, Diffie-Hellman Group and Key Life time in both phase1 and phase2. 4.5 DHCP Server Choose “DHCP Server”, you can see the next submenus: Click any of them, and you will be able to configure the corresponding function. 4.5.
PAGE 49
TX-VG1530 N300 Wireless VoIP GPON Router User Guide address has expired, the user will be automatically assigned a new dynamic IP address. The default is 24 hours.  Default Gateway - (Optional): It is suggested to input the IP address of the LAN port of the GPON router. The default value is 192.168.1.1.  Default Domain - (Optional): Input the domain name of your network.  DNS Server - (Optional): Input the DNS IP address provided by your ISP or consult your ISP.
PAGE 50
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Valid Time: The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. You cannot change any of the values on this page. To update this page and to show the current attached devices, click the Refresh button. 4.5.
PAGE 51
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 2. Modify the information. 3. Click the Save button. Click the Enable/Disable Selected button to make selected entries enabled/disabled. Click the Delete Selected button to selected entries. 4.5.4 Conditional Pool Choose menu “DHCP Server”“Conditional Pool”, you can see the next screen (shown in Figure 4-31). This page displays vendor class settings and allows you to set parameters for vendor class by clicking corresponding buttons.
PAGE 52
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Click the Enable/Disable Selected button to make selected entries enabled/disabled. Click the Delete Selected button to selected entries. 4.6 Wireless Choose “Wireless”, there are seven submenus to configure Wireless LAN settings. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.6.
PAGE 53
TX-VG1530 N300 Wireless VoIP GPON Router User Guide SSID. The wireless stations connected to different SSIDs can not communicate with each other.  Mode: Select the desired mode. 11b only: Select if all of your wireless clients are 802.11b. 11g only: Select if all of your wireless clients are 802.11g. 11n only: Select only if all of your wireless clients are 802.11n. 11bg mixed: Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixed: Select if you are using a mix of 802.
PAGE 54
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  SSID (to be bridged): The SSID of the AP your GPON router is going to connect to as a client. You can also use the search function to select the SSID to join.  BSSID (to be bridged): The BSSID of the AP your GPON router is going to connect to as a client. You can also use the search function to select the BSSID to join.  Scan: Click this button, you can search the AP which runs in the current channel.
PAGE 55
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  WPS: Enable or disable the WPS function here.  Current PIN: The current value of the GPON router's PIN is displayed here. The default PIN of the GPON router can be found in the label or User Guide.  Restore PIN: Restore the PIN of the GPON router to its default.  Gen New PIN: Click this button, and then you can get a new random value for the GPON router's PIN. You can ensure the network security by generating a new PIN.
PAGE 56
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Refer back to your client device or its documentation for further instructions. II. Enter the client device’s PIN on the GPON router Use this method if your client device has a Wi-Fi Protected Setup PIN number. Step 1: Keep the default WPS Status as Enabled and click the Add device button in Figure 4-34, then the following screen will appear. Figure 4-36 Step 2: Enter the PIN number from the client device in the field on the above WPS screen.
PAGE 57
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-37  SSID: Select the SSID from the drop-down list.  Disable Wireless Security: If you do not want to use wireless security, check this radio button. But it’s strongly recommended to choose one of the following modes to enable security.  WPA/WPA2 – Personal (Recommended): It’s the WPA/WPA2 authentication type based on pre-shared passphrase.
PAGE 58
TX-VG1530 N300 Wireless VoIP GPON Router User Guide • Wireless Password - You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters. • Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update.  WPA/WPA2 – Enterprise: It’s based on Radius Server. • Authentication Type: You can choose the version of the WPA security on the drop-down list.
PAGE 59
TX-VG1530 N300 Wireless VoIP GPON Router User Guide • Key Type: You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption. "Disabled" means this WEP key entry is invalid. • 64-bit: You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 ASCII characters. • 128-bit: You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 13 ASCII characters.
PAGE 60
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Start Time, End Time: You can select all day-24 hours or you may enter the Start Time and End Time in the corresponding field.  Add: Click this button to add your selected time to the below table. Click the Clear Schedule button to clear your settings in the table. Click Save to complete the settings. 4.6.
PAGE 61
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 2. Give a simple description for the wireless station in the Description field. For example: Wireless station A. 3. Select Enabled or Disabled for this entry on the Status drop-down list. 4. Click the Save button to save this entry. To edit or delete an existing entry: 1. Click the Edit in the entry you want to modify. 2. Modify the information. 3. Click the Save button.
PAGE 62
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-42  Transmit Power: Here you can specify the transmit power of GPON router. You can select High, Middle or Low which you would like. High is the default setting and is recommended.  Beacon Interval: Enter a value between 25-1000 milliseconds for Beacon Interval here. The beacons are the packets sent by the GPON router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons.
PAGE 63
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.6.7 Wireless Status Choose menu “Wireless””Wireless Status”, you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 4-43  MAC Address: The connected wireless station's MAC address.  Current Status: The connected wireless station's running status, one of STA-AUTH/ STA-ASSOC/ STA-JOINED/ WPA/ WPA-PSK/ WPA2/ WPA2-PSK/ AP-UP/ AP-DOWN/ Disconnected.
PAGE 64
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-44 You can enable or disable Guest Network. When you enable this function, you could set wireless parameters for Guest Network.  SSID: The guest network name. When setting up a Guest network, it is strongly recommended to use a name that easily distinguishes it from your primary network. The default name is TP-LINK_Guest_xxxxxx (xxxxxx is the last six numbers of MAC address).
PAGE 65
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.7.2 Guest Network Status Choose menu “Guest Network”“Guest Network Status”, you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 4-45  MAC Address: The connected wireless station's MAC address.  Current Status: The connected wireless station's running status.  Received Packets: Packets received by the station.  Sent Packets: Packets sent by the station.
PAGE 66
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-46  Profile Name: Displays the profile name of the account.  Registrar Address: Displays the IP address or domain name of the SIP Registrar server.  Phone Number: Displays the phone number of the account.  Status: Displays the status of the account. “Down” means that the account has not been registered.  Remove: Check the box and then click the Remove button below so that the very account will be deleted.
PAGE 67
TX-VG1530 N300 Wireless VoIP GPON Router User Guide SIP Account Advanced  Profile Name: Assign a name to identify the profile. Please note that special characters are not allowed.  Display Name: Assign a name for your account. This name is the Caller-ID you want to be displayed on your friend’s display panel, which can let your friend easily know who is calling. Please note that special characters are not allowed.
PAGE 68
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-48 Configure the current DigitMap settings, and click the Save button to make the configuration take effect. 4.8.3 Dial Plan Choose “Voice”“Dial Plan”, you can see the next submenus: This section includes Dial Plan List and Forbidden Call. The function allows users to set rules for outgoing calls. 4.8.3.1 Dial Plan List Choose “Voice”“Dial Plan” “Dial Plan List”, you will see the screen similar to Figure 4-49.
PAGE 69
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Enable: Displays the interface(s) enabled in this plan.  Remove: Check the box and then click the Remove button below so that the very plan will be deleted.  Edit: Click the Edit button to modify the very plan. To add a dial plan, click the Add button in Figure 4-49. Fill in the following parameters and click the Save button in Figure 4-50. Figure 4-50  Prefix: Set number(s) as the prefix. Up to 16 characters can be entered.
PAGE 70
TX-VG1530 N300 Wireless VoIP GPON Router User Guide • Add Number: If it is selected, the original phone number will be sent out with what you set in “Add Number” field added ahead. Take the 3rd dial plan in Figure 4-50 as an example. If you dial 018655556666, number 1795101865555666 will be dialed out to make a call.  Interface Enable: You can check any box to enable interface(s). Numbers matching prefix in DIal Plan List can only be dialed out through the selected interface(s).
PAGE 71
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.8.4 Phone Setup Choose “Voice”“Phone Setup”, you will see the screen similar to Figure 4-53. This section allows you to configure phone settings for phone 1 and phone 2. Figure 4-53  Phone Enable: Check the box behind to enable the function. Dial Settings  Dial Plan Priority: The parameters configured in the 2nd field determine which SIP account to use when making outgoing calls.
PAGE 72
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Dial Restriction: Choose the pull-down menu to set restriction for outgoing calls. • None: Allow all numbers to be dialed out. • All: Forbid all numbers to be dialed out. • According to Forbidden Call: Numbers will be dialed out according to settings in Forbidden Call.  WarmLine Enable: Check the box to enable WarmLine function.
PAGE 73
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.8.5 Advanced Setup Choose “Voice”“Advanced Setup”, you will see the next screen in Figure 4-54. Figure 4-54 SIP Advanced Setup:  Bound Interface Name: Bound Interface decides where to send/receive the VOIP traffic. Easy way to select the interface is to check the location of the SIP server. If it locates some where in the Internet then select Any_WAN. If it is on the local network then select LAN.
PAGE 74
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Registration Retry Interval(s): Set the time duration for your SIP Registrar server to keep your registration record. Before the time expires, the GPON router will send another register request to SIP Registrar again. If you are unsure of it, please always keep the default value.  Enable T38 support: T38 specifies a protocol for transmitting a fax across IP network in real time.
PAGE 75
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Click the Save button to make the configuration take effect. If you want to delete the entry, check the Remove box first, and then click the Remove button. 4.8.7 Call Log Choose “Voice”“Call Log”, you will see the screen as shown in Figure 4-58. This function allows you to view call logs and configure call log options. Figure 4-58  Call Log: Check the Enable if you want to make this function take effect; otherwise check the Disable.
PAGE 76
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.8.8 Call Firewall Choose “Voice”“Call Firewall“, you can see the next submenus: Call Firewall can be used to control incoming calls. This section introduces how to configure the Call Firewall. Choose “Voice”“Call Firewall““Mode Setting“, you will see the screen as shown in Figure 4-60. Figure 4-60  Call Firewall Enable: Check the box if you want to make the Call Firewall take effect.  Black: Check the Black box to enable Black List mode.
PAGE 77
TX-VG1530 N300 Wireless VoIP GPON Router User Guide To add a new entry, click the Add button and you will see the screen as shown in Figure 4-62. Figure 4-62 Enter a number with the length in the range of [3, 16]in the field of Black List Number and Click the Save button to make the configuration take effect, then you will go back to the previous page and see the following list as shown in Figure 4-61. If you want to delete the entry, check the Remove box first and then click the Remove button.
PAGE 78
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.8.9 USB Voice Mail Choose “Voice”“USB Voice Mail“, you will see the screen as shown in Figure 4-65. USB Voice mail is used to record voice messages when the call is not answered. To use this function, please make sure an external USB hard drive/USB flash disk with configure files has been plugged into the USB port on the GPON router. Figure 4-65  Phone: Displays the phone that has voice message.
PAGE 79
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-66  Enable Local Play Operation Notify: Check this box so there will be sound indication for operation when you listen to the voice messages. This is enabled by default. If you are very familiar with the operations, you can disable it.  Enable Global Wav Format: Check this box and all the voice message will be saved as wav files in your USB device. It is convenient for users to listen to the voice messages on the computer.
PAGE 80
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 3) Input the PIN code according to the notification. 4) You can listen to all the new messages after the PIN code is validated. Click Save to save your configurations. Click Back to go back to the previous page, i.e. Figure 4-65. 4.9 USB Settings There are six submenus under the USB Settings menu, USB Mass Storage, User Accounts, Storage Sharing, FTP Server, Media Server and Print Server.
PAGE 81
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Capacity: The storage capacity of the USB driver.  Status: Indicates the shared or non-shared status of the volume. Active means volume can be shared, while Inactive means volume can not be shared. If Deactivate in Action field is enabled, Inactive will be displayed in the Status field, which means volume can not be shared.
PAGE 82
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4. Re-enter the password in the Confirm Password field. 5. Click the Set button, and then a new entry will be added in the table. 6. Click the Apply button to apply your settings. Click the Refresh button to refresh this page immediately. 4.9.3 Storage Sharing Choose menu “USB Settings” → “Storage Sharing”, you can configure a USB disk drive attached to the GPON router and view volume and share properties on this page as shown below.
PAGE 83
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-70 2. 3. 4. Click the Browse button, and then select the Select Volume from the drop-down list. Enter display name of the share folder in Share Name filed. Click the Apply button to apply the settings. You can click the upper button to go to the upper folder Click the Enable/Disable Selected button to enable or disable the selected entries. Click the Delete Selected button to delete the selected entries.  Note: 1.
PAGE 84
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-71  Server Status: Indicates the FTP Server's current status.  Internet Access: Enable or disable this function.  Internet Address: If Internet Access is enabled, WAN IP will be displayed here.  Service Port: Enter the FTP Port number to use. The default is 21.  Share Name: This folder's display name.  Directory: The real full path of the specified folder.  User Index: The authorization of the user is displayed.
PAGE 85
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-72 2. 3. 4. Click the Browse button, and then select the Select Volume from the drop-down list. Enter display name of the share folder in Share Name filed. Click the Apply button to apply the settings. You can click the upper button to go to the upper folder. Click the Enable/Disable Selected button to enable or disable the selected entries. Click the Delete Selected button to delete the selected entries.  Note: 1.
PAGE 86
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Server Enable: Select this box to enable this function.  Server Name: The name of this Media Server. To add a new share folder for your media server, please follow the instructions below: a) Click Add New Folder button, and you will see the screen as shown in Figure 4-91. b) Enter the name of the share folder in Share Name field. c) Click the Apply button to apply the configuration.
PAGE 87
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.10 Route Settings Choose “Route Settings”, it includes three menus: Default Gateway, Static Route and RIP Settings. The detailed descriptions are provided below. 4.10.1 Default Gateway Choose “Route Settings”“Default Gateway”, you can see the Default Gateway screen. You can select a WAN Interface from the drop-down list as the system default gateway. Figure 4-76 Click the Add Interface button, you can add WAN Interfaces.
PAGE 88
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-78 2. Enter the following data:  Destination IP Address: The Destination IP Address is the address of the network or host that you want to assign to a static route.  Subnet Mask: The Subnet Mask determines which portion of an IP Address is the network portion, and which portion is the host portion.
PAGE 89
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Note: RIP cannot be configured on the WAN Interface which has NAT enabled (such as PPPoE). 4.11 IPv6 Route Settings Choose “IPV6 Route Settings”, it includes three menus: IPv6 Default Gateway, IPv6 Static Route. The detailed descriptions are provided below. 4.11.1 IPv6 Default Gateway Choose “IPv6 Route Settings”“IPv6 Default Gateway”, you can see the IPv6 Default Gateway screen.
PAGE 90
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 1. Click the Add New button in Figure 4-81, and you will see the screen as shown in Figure 4-82. Figure 4-82 2. Enter the following data:  Destination IP Address: The Destination IP Address is the address of the network or host that you want to assign to a static route.  Subnet Mask: The Subnet Mask determines which portion of an IP Address is the network portion, and which portion is the host portion.
PAGE 91
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.12.1 Virtual Servers Choose menu “Forwarding” → “Virtual Servers”, and then you can view and add virtual servers in the next screen (shown in Figure 4-83). Virtual servers can be used for setting up public services on your LAN. A virtual server is defined as a service port, and all requests from Internet to this service port will be redirected to the computer specified by the server IP.
PAGE 92
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-84  Note: It is possible that you have a computer or server that has more than one type of available service. If so, select another service, and type the same IP address for that computer or server. To modify or delete an existing entry: 1. Find the desired entry in the table. 2. Click Edit as desired on the Edit column. Click the Enable/ Disabled Selected button to make selected entries enabled/ disabled.
PAGE 93
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 1. Click the Add New button, the next screen will pop-up as shown in Figure 4-86. 2. Select a common application from the Common Service Port drop-down list, then the Trigger Port field and the Open Ports field will be automatically filled. If the Common Service Port do not have the application you need, enter the Trigger Port and the Open Ports manually. 3.
PAGE 94
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 2. Click Edit as desired on the Edit column. Click the Enable/ Disabled Selected button to make selected entries enabled/ disabled. Click the Delete Selected button to delete selected entries. Once the GPON router is configured, the operation is as follows: 1. 2. 3. A local host makes an outgoing connection to an external host using a destination port number defined in the Trigger Port field.
PAGE 95
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.12.4 UPnP Choose menu “Forwarding→UPnP”, and then you can view the information about UPnP in the screen (shown in Figure 4-88). The Universal Plug and Play (UPnP) feature allows the devices, such as Internet computers, to access the local host resources or devices as needed. UPnP devices can be automatically discovered by the UPnP service application on the LAN.
PAGE 96
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-89  Enable Parental Control: Check the box if you want this function to take effect. This function is disabled by default.  MAC Address of Parental PC: In this field, enter the MAC address of the controlling PC, or you can make use of the Copy To Above button below.  MAC Address of Current PC: This field displays the MAC address of the PC that is managing this GPON router.
PAGE 97
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.14 Firewall There are four submenus under the Firewall menu: Rule, LAN Host, WAN Host and Schedule. Click any of them, and you will be able to configure the corresponding function. 4.14.1 Rule Choose menu “Firewall” → “Rule”, and then you can view and set Access Control rules in the screen as shown in Figure 4-90. Figure 4-90  Enable Firewall: Select the check box to enable the Firewalll function, so the default filtering rules can take effect.
PAGE 98
TX-VG1530 N300 Wireless VoIP GPON Router User Guide The methods to add a new rule: 1. Click the Add New button and the next screen will pop up as shown in Figure 4-91. 2. Give a name (e.g. Rule_1) for the rule in the Description field. 3. Select a host from the LAN Host drop-down list or choose “Add LAN Host”. 4. Select a target from the WAN Host drop-sown list or choose “Add WAN Host”. 5. Select a schedule from the Schedule drop-down list or choose “Add Schedule”. 6.
PAGE 99
TX-VG1530 N300 Wireless VoIP GPON Router User Guide To add a new entry, please follow the steps below. 1. Click the Add New button. 2. In the Mode field, select IP Address or MAC Address.  If you select IP Address, please follow the steps below: 1) In Description field, create a unique description for the host (e.g. Host_1). 2) In IP Address field, enter the IP address.  If you select MAC Address, please follow the steps below: 1) In Description field, create a unique description for the host (e.g.
PAGE 100
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 2) In IP Address field, enter the IP address. If you select MAC Address, the screen shown is Figure 4-95. Figure 4-95 1) In Description field, create a unique description for the host (e.g. Host_1). 2) In MAC Address field, enter the MAC address. If you select URL Address, the screen shown is Figure 4-96. Figure 4-96 1) In Description field, create a unique description for the host (e.g. Host_1).
PAGE 101
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Edit: Here you can modify an existing schedule. To add a new schedule, follow the steps below: 1. Click Add New button and the next screen will pop-up as shown in Figure 4-98. 2. In Description field, create a unique description for the schedule (e.g. Schedule_1). 3. In Apply To field, select the day or days you need. 4. In time field, you can select all day-24 hours or you may enter the Start Time and Stop Time in the corresponding field. 5.
PAGE 102
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.15.1 IPv6 Rule Choose menu “IPv6 Firewall” → “IPv6 Rule”, and then you can view and set Access Control rules in the screen as shown in Figure 4-99. Figure 4-99  Enable IPv6 Firewall: Select the check box to enable the IPv6 Firewall function, so the Default Filtering Rules can take effect.  Description: Here displays the description of the IPv6 rule and this name is unique.
PAGE 103
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 3. Select a host from the IPv6 LAN Host drop-down list or choose “Add IPv6 LAN Host”. 4. Select a target from the IPv6 WAN Host drop-sown list or choose “Add IPv6 WAN Host”. 5. Select a schedule from the IPv6 Schedule drop-down list or choose “Add IPv6 Schedule”. 6. In the Action field, select Deny or Allow to deny or allow your entry. 7. In the Status field, select Enabled or Disabled to enable or disable your entry. 8.
PAGE 104
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4. Enter the prefix length of the IPv6 address in the Prefix Length field. 5. Click the Save button to save the settings. Click the Delete Selected button to delete selected entries. 4.15.3 IPv6 WAN Host Choose menu “IPv6 Firewall” → “IPv6 WAN Host”, and then you can view and set a Host list in the screen as shown in Figure 4-103. Figure 4-103  Description: Here displays the description about the WAN and this description is unique.
PAGE 105
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-105  Description: Here displays the description of the schedule and this description is unique.  Edit: Here you can modify an existing schedule. To add a new schedule, follow the steps below: 1. Click Add New button and you will see the screen as shown in Figure 4-106. Figure 4-106 2. Create a unique description for the schedule (e.g. Schedule_1) in Description field. 3. Select the day or days you need in Apply To field. 4.
PAGE 106
TX-VG1530 N300 Wireless VoIP GPON Router User Guide IPv6 completely supplants IPv4. It is a temporary solution for networks that do not support native dual-stack, where both IPv6 and IPv4 run independently. Choose menu “IPv6 Tunnel”, and you will see the screen as shown in Figure 4-107. Figure 4-107  Enable: Check the box to enable IPv6 Tunnel function. It is disabled by default.  Mechanism: Select a type for IPv6 tunnel from the drop-down list. DS-Lite, 6RD and 6to4 are supported.
PAGE 107
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-109  WAN Connection: Select a WAN connection from the drop-down list. Only the connected WAN connections can be shown in the drop-down list.  Configuration Type: Select a configuration type for this tunnel. Auto means to obtain the following parameters automatically while Manual means you set them manually. If Auto is selected, only Dynamic IP connection can be selected from the drop-down list.
PAGE 108
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.17 Quality of Service QoS (Quality of Service) helps to prioritize data as it enters your router. By attaching special identification marks or headers to incoming packets, QoS determines which queue the packets enter, based priority. This is useful when there are certain types of data you want to give higher priority, such as voice data packets give higher priority than Web data packets.
PAGE 109
TX-VG1530 N300 Wireless VoIP GPON Router User Guide • • • SP-Mode: Strict-Priority Mode. In this mode, the queue with higher priority will occupy the whole bandwidth. Packets in the queue with lower priority are sent only when the queue with higher priority is empty. The disadvantage of SP queue is that: if there are packets in the queues with higher priority for a long time in congestion, the packets in the queues with lower priority will be “starved to death” because they are not served.
PAGE 110
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-112 Queue: Click Add New button shown in queue part in Figure 4-112, you can add a new queue in Figure 4-113. Figure 4-113  Direction: Select the direction.  Scheduler Algorithm: Displays the Scheduler Algorithm you have chosen in Figure 4-111  Queue Name: Enter a name for the queue.  Status: Select the status of the queue is enabled or disabled.
PAGE 111
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Note: 1) Only enable the QoS function of the relevant direction, the queue configuration in SP or WRR mode could take effect. 2) At most you could establish 8 upstream queues and 8 upstream queues. Click the Save button to save your settings. Click Back to go back to the previous page Flow classification: Flow classification function identifies packets conforming to certain characters according to certain rules.
PAGE 112
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Mark Differentiated Service Code Point (DSCP): Enter the number to remark the DSCP priority. To make this function take effect, make sure you have enabled DSCP mark in Figure 4-111.  Mark 802.1P Priority: Select the type to remark the 802.1p priority. To make this function take effect, make sure you have enabled 802.1P mark in Figure 4-111. Click the Save button to save your settings.
PAGE 113
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.17.3 Bandwidth Control Choose menu “Quality of Service” → “Bandwidth Control”, and then you can view and configure the Bandwidth Control rules in the screen below. Figure 4-116  Description: This is the information about the rules such as address range.  Upstream Bandwidth: This field displays the max and mix upload bandwidth through the WAN port, the default is 0.
PAGE 114
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.18 IP&MAC Binding There are two submenus under the IP &MAC Binding menu: Binding Settings and ARP List. Click any of them, and you will be able to scan or configure the corresponding function. The detailed explanations for each submenu are provided below. 4.18.1 Binding Settings This page displays the IP & MAC Binding Setting table; you can operate it in accord with your desire (shown in Figure 4-118).
PAGE 115
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 2. Enter the MAC Address and IP Address. 3. Select the Bind checkbox. 4. Click the Save button to save it. To modify or delete an existing entry, follow the steps below. 1. Find the desired entry in the table. 2. Click Edit as desired on the Edit column. Click the Enable/ Disable Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete selected entries. 4.18.
PAGE 116
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-121  Service Provider: This field displays the service provider of DDNS.  Domain Name: Enter the Domain name you received from dynamic DNS service provider.  Username & Password: Type the “User Name” and “Password” for your DDNS account.  Enable DDNS: Activate the DDNS function or not.  Login/ Logout: Login to or logout of the DDNS service. 4.
PAGE 117
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.21 System Tools Choose menu “System Tools”, and you can see the submenus under the main menu: System Log, Time Settings, Manage Control, CWMP Settings, SNMP Settings, Backup & Restore, Factory Defaults, Firmware Upgrade, Reboot and Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.21.
PAGE 118
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Figure 4-124  Save Locally: If Save Locally is selected, events will be recorded in the local memory.  Minimum Level: Select the Minimum level in the drop-down list, for the Minimum Level, all logged events above or equal to the selected level will be displayed.  Save Remotely: If Save Remotely is selected, events will be sent to the specified IP address and UDP port of the remote system log server. Click the Save button to save your settings. 4.
PAGE 119
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 2. Enter the Date in Year/Month/Day format. 3. Enter the Time in Hour/Minute/Second format. 4. Click Save. To set time automatically: 1. Select your local time zone. 2. 3. Enter the address or domain of the NTP Server 1 or NTP Server 2. Click the Get GMT button to get system time from Internet if you have connected to the Internet. 4.21.
PAGE 120
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4.21.4 CWMP Settings Choose “System Tools” → “CWMP Settings”, you can configure the CWMP function in the screen. The GPON router offers CWMP feature. The function supports TR-069 protocol which collects information, diagnoses the devices and configures the devices automatically via ACS (Auto-Configuration Server). Figure 4-127  CWMP: Select enable the CWMP function.  Inform: Enable or disable the function.
PAGE 121
TX-VG1530 N300 Wireless VoIP GPON Router User Guide SNMP (Simple Network Management Protocol) has been widely applied in the computer networks currently, which is used for ensuring the transmission of the management information between any two nodes. In this way, network administrators can easily search and modify the information on any node on the network. Meanwhile, they can locate faults promptly and implement the fault diagnosis, capacity planning and report generating.
PAGE 122
TX-VG1530 N300 Wireless VoIP GPON Router User Guide restart automatically then. Keep the power of the GPON router on during the process, in case of any damage. 4.21.
PAGE 123
TX-VG1530 N300 Wireless VoIP GPON Router User Guide  Hardware Version: Displays the current hardware version. The hardware version of the upgrade file must accord with the GPON router’s current hardware version. To upgrade the GPON router's firmware, follow these instructions below: 1. Download a most recent firmware upgrade file from our website (www.tp-link.com). 2. Enter or select the path name where you save the downloaded file on the computer into the File Name blank. 3.
PAGE 124
TX-VG1530 N300 Wireless VoIP GPON Router User Guide • Update the configuration with the file (system will reboot automatically. 4.21.10 Statistics Choose menu “System Tools” → “Statistics”, and then you can view the statistics of the GPON router, including total traffic and current traffic of the last Packets Statistic Interval. Figure 4-133  Statistics Status: Enable or Disable. The default value is disabled. To enable it, click the Enable.
PAGE 125
TX-VG1530 N300 Wireless VoIP GPON Router User Guide IP/MAC Address Total Current Operation 4.22 The IP and MAC address are displayed with related statistics. Packets The total number of packets received and transmitted by the GPON router. Bytes The total number of bytes received and transmitted by the GPON router. Packets The total number of packets received and transmitted in the last Packets Statistic interval seconds.
PAGE 126
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Appendix A: Specifications General Standards and Protocols ITU 984.1，ITU 984.2，ITU 984.3， ITU 984.4, IEEE802.1p, IEEE 802.11b,IEEE802.11e, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3u, TCP/IP, PPPoE, SNTP, HTTP, DHCP, ICMP, NAT Safety & Emission FCC, CE Ports Four 10/100/1000M Auto-Negotiation RJ45 ports（Auto MDI/MDIX) One optical port, Two RJ11 ports, One USB 2.
PAGE 127
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Appendix B: Troubleshooting T1. How do I restore my GPON router’s configuration to its factory default settings? With the GPON router powered on, press and hold the RESET button on the front panel for at least 6 seconds before releasing it.  Note: Once the GPON router is reset, the current configuration settings will be lost and you will need to re-configure the router. T2.
PAGE 128
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK.  For Windows 8  Move your mouse to the lower right corner and you will see Search icon in the Popups. Go to “ -> Apps”. Type Control Panel in the search box and press Enter, then you will go to Control Panel.  Click “View network status and tasks > Change adapter settings”.  Right-click “Ethernet” and then select Properties.
PAGE 129
TX-VG1530 N300 Wireless VoIP GPON Router User Guide 4) Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your GPON router’s factory default settings and reconfigure your GPON router following the instructions in 3.2 Quick Installation Guide. Please feel free to contact our Technical Support if the problem still exists. T4.
PAGE 130
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Appendix C: Telephony Features This section introduces what the following features are used for. Call Holding This feature allows you to put a call on hold, in which case the call is not ended but no verbal communication is available. To put a call on hold, press the FLASH button. To return to the original call, press the FLASH button again.
PAGE 131
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Anonymous Call Blocking With this feature enabled, all anonymous calls will be blocked. Speed Dial This feature allows you to create short numbers for your frequently used telephone numbers to make your dialing more convenient. You just need to press one or two digits and the key # instead of the original phone number to make a call.
PAGE 132
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Appendix D: Telephone Operation The table below guides you to configure some frequently used call features using keypads on your telephone. For the features mentioned in this table, please refer to Telephony Features in Appendix C. Code Description Usage Pick up the phone to dial this code and then follow the voice prompts for the operations below: *20 Listen to voice messages stored in your USB storage device. Press 0 to listen to new messages.
PAGE 133
TX-VG1530 N300 Wireless VoIP GPON Router User Guide *71 Enable Call Forwarding on No Answer. Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect. *72 Enable Call Forwarding on Busy. Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect. *73 Enable Call Forwarding Unconditionally. Pick up the phone to dial this code.
PAGE 134
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Anonymous Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect. *84 Disable Calling. *86 Enable DND (Do Not Disturb). Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect. *87 Disable DND (Do Not Disturb). Pick up the phone to dial this code.
PAGE 135
TX-VG1530 N300 Wireless VoIP GPON Router User Guide Appendix E: Technical Support Technical Support  For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq  To download the latest Firmware, Driver, Utility and User Guide, go to: http://www.tp-link.com/en/support/download  For all other technical support, please contact us by using the following details: Global Tel: +86 755 2650 4400 Fee: Depending on rate of different carriers, IDD. E-mail: support@tp-link.