User Guide AC1600 Wireless Gigabit VoIP VDSL/ADSL Modem Router Archer VR600v REV2.0.
Contents About This Guide..........................................................................................................1 Chapter 1. Get to Know Your Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . 2 1. 1. 1. 2. Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Physical Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. 3. 6. 4. 6. 5. 6. 6. 6. 7. 6. 8. 6. 2. 2. Configuring DECT Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Entering Telephone Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Telephone Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 6. 4. 1. Telephone Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11. 4. IP & MAC Binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 11. 5. IPv6 Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Chapter 12. NAT Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 12. 1. 12. 2. 12. 3. 12. 4. 12. 5. Translate Address and Port by ALG . . . . . . . . . . . . . . .
15. 3. Update the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 15. 3. 1. Online Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 15. 3. 2. Local Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 15. 4. Back up and Restore Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About This Guide This guide is a complement to Quick Installation Guide. The Quick Installation Guide provides instructions for quick internet setup, while this guide contains details of each function and demonstrates how to configure them in typical scenarios. When using this guide, please notice that features of the router may vary slightly depending on the model and software version you have, and on your location, language, and internet service provider.
Chapter 1 Get to Know Your Modem Router This chapter introduces the modem router by detailing its main features and appearance.
Chapter 1 1. 1. Product Overview TP-Link’s modem router is a combined wired/wireless network connection device with wireless router and DSL modem capabilities. With DSL and LAN/WAN ports, the modem router is compatible with DSL connections and fiber/cable access. Ethernet ports and adjustable antennas enable the modem router to provide wired and wireless access for multiple computers and mobile devices.
Chapter 1 LED Explanation Name Power Status On Flashing Off On DSL Flashing Off On Internet Wireless 2.4GHz / Wireless 5GHz LAN Off On Flashing Off On Off On USB Phone Flashing Off On Flashing Off Indication The system has started up successfully. The system is starting up or firmware is being upgraded. Do not disconnect or power off your modem router. Power is off. Please ensure that the power adapter is connected correctly. DSL synchronization is complete.
Chapter 1 1. 2. 2. Back Panel The modem router’s back panel shows the ports, buttons and antennas. Refer to the following for detailed instructions. Item Phone1/Phone2 DSL USB LAN1, LAN2, LAN3, LAN4/WAN Power Antennas Description For connecting your analog phone to the modem router. Connect your analog phones to the RJ11 ports on the back panel. For connecting the modem router to the internet. Connect the port to the splitter or directly connect the port to the phone jack via a phone cable.
Chapter 1 1. 2. 3. Side Panel The modem router’s side panel shows the buttons and ports. Refer to the following for detailed instructions. Item Power On/Off Reset WPS Wi-Fi DECT Description The switch for the power. Press it to power on or off the modem router. Press and hold down for 10 seconds to reset the modem router to factory default settings. Press to start a WPS synchronization. Press to turn both 2.4GHz and 5GHz Wi-Fi on or off.
Chapter 2 Connect the Hardware This chapter contains the following sections: • Position Your Modem Router • Connect Your Modem Router
Chapter 2 2. 1. Connect the Hardware Position Your Modem Router With the modem router, you can access your network from anywhere within the wireless network coverage. However, the wireless signal strength and coverage varies depending on the actual environment where your modem router is in. Many obstacles may limit the range of the wireless signal, for example, concrete structures, thick walls.
Chapter 2 Connect the Hardware 1 Attach the antennas. Power Adapter 3 Push in to turn on the modem router. Phone Jack L DS 2 one Ph 1 1 one Ph Connect the DSL splitter to the phone jack. Modem Router P H O N E M O D E M E LIN 2 Connect the modem router to the DSL splitter. DSL Splitter For traditional landline phone service 2. Connect your computer to the modem router.
Chapter 2 Connect the Hardware Computer Smart Device Connections are available CHOOSE A NETWORK... TP-Link_XXXX TP-Link_XXXX_5G Connect automatically Wi-Fi Wi-Fi Wireless Network Connection √ < Settings Connect TP-Link_XXXX TP-Link_XXXX_5G Other... Method 3: Use the WPS button Wireless devices that support WPS, including Android phones, tablets, most USB network cards, can be connected to your router through this method. (WPS is not supported by iOS devices.
Chapter 3 Log In to Your Modem Router
Chapter 3 Log In to Your Modem Router With the web management page, it is easy to configure and manage the modem router. The web management page can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. Follow the steps below to log in to your modem router. 1. If the TCP/IP Protocol on your computer is set to the static (fixed) IP address, you need to change its settings to obtain an IP address automatically.
Chapter 4 Set Up Internet Connections This chapter introduces how to connect your modem router to the internet. The modem router is equipped with a web-based Quick Setup wizard. It has many ISP information built in, automates many of the steps and verifies that those steps have been successfully completed. Furthermore, you can also set up an IPv6 connection if your ISP provides IPv6 service.
Chapter 4 4. 1. Set Up Internet Connections Use Quick Setup Wizard 1. Visit http://tplinkmodem.net, and log in with the password you set for the modem router. 2. Click Quick Setup on the top of the page. Then follow the step-by-step instructions to connect your router to the internet. 3. To enjoy a more complete service from TP-Link (remote management, TP-Link DDNS, etc.), log in with your TP-Link ID or click Register Now to get one.
Chapter 4 Set Up Internet Connections 3. Click Save to make the settings effective, and you can refer to Test Internet Connectivity to test the internet connection. Tips: You can view and edit all internet connection settings on the Advanced > Network > Internet page. 4. 3. Test Internet Connectivity After manually setting up the internet connection, you need to test the internet connectivity. The modem router provides a diagnostic tool to help you locate the source of any problems. 1.
Chapter 4 Set Up Internet Connections 3. Click Start to test the internet connectivity and you will see the test result in the gray box. 4. 4. Set Up an IPv6 Connection If your ISP has provided a DSL line that supports IPv6 connection as well as some detailed IPv6 parameters, you can manually set up an IPv6 connection. If your ISP provides an IPv4-only connection or IPv6 tunnel service, permit IPv6 connection by referring to Set Up the IPv6 Tunnel.
Chapter 4 Set Up Internet Connections 5. Scroll down the page, enable IPv6, and configure the IPv6 parameters. • • Addressing Type: Consult your ISP for the addressing type (DHCPv6 or SLAAC). SLAAC is the most commonly used addressing type. IPv6 Gateway: Keep the default setting as Current Connection. Note: If your ISP has provided the IPv6 address, click Advanced to reveal more settings. Check to use IPv6 specified by ISP and enter the parameters provided by your ISP. 6.
Chapter 4 Set Up Internet Connections 5. Go to Basic > Internet, select the Connection Type, and enter the information provided by your ISP. 6. Click Save to make the settings effective. Tips: 1. You can view and edit all internet connections on Advanced > Network > Internet page. 2. In the Wireless Router Mode, you can also permit IPv6 connection by setting up an IPv6 connection or the IPv6 tunnel just as in the DSL Modem Router Mode.
Chapter 5 TP-Link Cloud Service TP-Link Cloud service provides a better way to manage your cloud devices. Log in to your router with a TP-Link ID, and you can easily monitor and manage your home network when you are out and about via the Tether app on your smartphone or tablet. To ensure that your router stays new and gets better over time, the TP-Link Cloud will notify you when an important firmware upgrade is available. Surely you can also manage multiple TP-Link Cloud devices with a single TP-Link ID.
Chapter 5 5. 1. TP-Link Cloud Service Register a TP-Link ID If you have skipped the registration during the Quick Setup process, you can： 1. Visit http://tplinkmodem.net, and log in with the account you set for the router. 2. Go to Basic > TP-Link Cloud. 3. Click Register Now and follow the instructions to register a TP-Link ID. 4. After activating your TP-Link ID, come back to the TP-Link Cloud page to log in.
Chapter 5 TP-Link Cloud Service ¾¾ Change your password 1. Click behind the Password. 5. 3. Manage the User TP-Link IDs 2. Enter the current password, then a new password twice. And click Save. The first-time login TP-Link ID will be bound automatically to your router as an Admin account. An admin account can add or remove other TP-Link IDs to the same router as Users.
Chapter 5 TP-Link Cloud Service • Add/remove other TP-Link IDs to/from the router. 5. 3. 1. Add an TP-Link ID to Manage the Router 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID. 2. Go to Basic > TP-Link Cloud, and focus on the Bound Accounts section. 3. Click , enter another TP-Link ID as needed and click Save. Note: If you need another TP-Link ID, please refer to Manage the Router via TP-Link Tether App to install the app and register a new one. 4.
Chapter 5 5. 4. TP-Link Cloud Service Manage the Router via TP-Link Tether App The Tether app runs on iOS and Android devices like smartphones and tablets. 1. Open the Apple App Store or Google Play and search the key word TP-Link Tether or simply scan the QR code to download and install the app. OR 2. Connect your device to the router’s wireless network. 3. Launch the Tether app, select the model of your router and log in with your TP-Link ID or the password you set for the router. 4.
Chapter 6 Telephony This chapter guides you on how to make telephone calls via internet.
Chapter 6 6. 1. Telephony Connecting the Telephone Connect your telephone to the TAE ports on the side panel or RJ11 ports on the back panel. Please note that you can only connect to two ports (one to a Phone 1 and the other to a Phone 2) at most. Pho ne 1 Pho ne 2 RJ-11 6. 2. DECT 6. 2. 1. Registering DECT Handset The modem router is integrated with DECT (Digital Enhanced Cordless Telecommunications) function.
Chapter 6 Telephony 2. Enter the PIN (Default: 0000) on the DECT handset if required. Notes: 1. Up to six DECT handsets can be registered on the modem router. 2. If you press the DECT button for more than 4 seconds, and the Phone LED still does not light, release the button and try again. Method 2: Via Web Management Interface Follow the steps below to register: 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2.
Chapter 6 Telephony 3. Enable DECT. 4. The PIN code is needed when registering your cordless phone. The default is 0000. Change it by entering a new one. 5. Reduce DECT field strength: Check the box to enable this function. In this mode, base transmit power will be decreased. Then the DECT Handset will have signal within a small distance. 6. Eco DECT: Only when all handsets support Eco Mode, will it take effect.
Chapter 6 Telephony 3. Choose your Telephony Provider and enter the necessary information as required, and click Save to make the settings effective. 4. If your telephony provider is not listed here, choose Other provider, enter the information as required, and click Save to make the settings effective. Phone Number: The number you use to dial and answer. Registrar Address: Usually a domain name, if not, an IP address.
Chapter 6 Telephony Advanced: Click to have more configuration. 5. In the Area Code section, enable this function and enter the area code of your city or region. This can spare you the trouble of including the area code each time you make a local call over the internet. 6. Click Save to make the settings effective. Advanced: Click to have more configuration. To have more configuration on telephony settings Click Advanced under Advanced Settings to configure more telephony settings.
Chapter 6 Telephony DTMF Relay Setting: DTMF is Dual Tone Multi Frequency. Options available are SIP-Info, RFC2833, and In-band. If you are unsure which one to choose, please always keep the default value. • SIP INFO: If it is selected, the modem router will capture the DTMF tone and transfer it into SIP form. Then it will be sent to the remote end with SIP message.
Chapter 6 Telephony 2. Go to Advanced > Telephony > Telephone Book. Click Add to enter a new contact’s information. 3. You can set speed dial number for certain numbers. Speed dial function allows you to reach the desired party by dialing the reduced number of keys rather than a long phone number. 4. Click OK to save the settings. 6. 4. 2. Emergency Calls I want to: Make my telephone automatically call a specific contact when the handset is picked up but no operation is done within a period of time.
Chapter 6 Telephony 3. Enable Emergency Number. 4. No Operation Time: Set how long should the telephone wait before the first number is automatically dialed). 5. Emergency Number: Set the number to be automatically reached. If more than one number is set, the modem router will automatically call the next one if the previous is not answered. 6. Click Save to make the settings effective. Done! 6. 5.
Chapter 6 Telephony 3. Click to manage your telephony devices. 4. Device Name: Name the telephone device here. 5. Number for Outgoing Calls: Assign an outgoing number for this phone. 6. Number for Incoming Calls: Tick the incoming number for this phone. 7. VAD Support: VAD (Voice Activation Detection) prevents transmitting the silence packets to consume the bandwidth. It is also known as Silence Suppression, a software application that ensures bandwidth when voice activity is activated. 8.
Chapter 6 Telephony 10. Click OK to make the settings effective. Done! Now your telephony devices are bound to different incoming call numbers and outgoing call numbers. Tips: Internal number showed on the table are used to make calls between telephony devices connected to the same modem router. It is preset and cannot be changed. 6. 6. Call Log I want to: Have a call list recording detailed information of incoming calls and outgoing calls on your modem router. How can I do that? 1.
Chapter 6 Telephony dialed via this number. How can I do that? 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > Telephony > Call Rules. Click Add to set call rules. 3. Choose Long Distance in Call Type or Prefix. Prefixes and call types can vary according to your own circumstances. 4. In Number for Outgoing Calls, choose the number that has low charge in making long distance calls. 5. Click OK to make the settings effective.
Chapter 6 Telephony How can I do that? 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > Telephony > DND & Call Blocking. 3. Enable DND. 4. Set the day(s) when DND is enabled. 5. Click Save to make the settings effective. Done! 6. 8. 2. Now, within this period of time, no telephone will ring, but all incoming calls would be recorded in call log.
Chapter 6 Telephony 5. Click OK to make the settings effective. Done! 6. 8. 3. From now on, these calls are all automatically blocked by your modem router. Prevent from Dialing I want to: Prevent my modem router from dialing a certain type of numbers. How can I do that? 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router.
Chapter 6 Telephony forwarded to my mobile phone so that I won’t miss it. How can I do that? 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > Telephony > Call Forwarding. Click Add to set how calls should be forwarded. 3. Select the incoming calls to be forwarded: Choose to forward which call or call type. 4. Destination Telephone Number: Set the destination where calls should be forwarded. 5.
Chapter 6 Telephony 6. 10. Call Through I want to: Call someone through my telephone number registered on my modem router. For example, I am away from home, and want to call a friend who is aboard. I can call the friend using my mobile phone of course, but that would cost a huge sum. Meantime, my telephone number has a low charge in making international calls. So it would be great if I can call the friend using my mobile phone and my telephone number. Fortunately, you can do that.
Chapter 6 Telephony 1. Use your mobile to call the incoming number you selected in step 4. 2. Put in the PIN code when you hear the tone, remember to end the PIN with a “#”. Change of the default PIN code is recommended. 3. Dial the number of your friend. 4. At this time, your friend will receive a call from the outgoing number your selected in step 5. You can talk to your friend from your mobile phone. 6. 11. tpPhone tpPhone is an App allowing you to make and receive calls through VoIP modem router.
Chapter 6 Telephony 6. 12. Voice Mail I want to: Allow the caller who is not answered to leave a voice mail. How can I do that? 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. For example, I’m on my vocation, and cannot receive any call at the moment. If people who called can leave a voice mail, I would know what was going on when I was absent from home. 2. Go to Advanced > Telephony > Voice Mail. 3. Enable Voice Mail.
Chapter 6 Telephony 4. Set the “No answer“ Time. A time period. If the call is not answered within this time period, the caller can leave a voice mail. 5. Choose greetings for your Voice Mail. You can record the greeting by dialing *30 on the keyboard of your telephone. 6. Set how long a voice mail can last at Voice Mail Duration. 7. If you want to access your voice mail remotely, enable Remote Access Voice Mail and create a new Remote Access PIN to make this function available.
Chapter 7 IPTV IPTV is the abbreviation of Internet Protocol Television. The service can only be delivered through the Internet, and our modem router provides a specific LAN port for IPTV. By automatically separating IPTV from Internet surfing, you can enjoy a high quality of video streaming and fast browsing speeds at the same time.
Chapter 7 I want to: Configure the modem router to enable Internet Protocol Television (IPTV) Services. For example, I already bought IPTV service, but this service can only be delivered through the Internet. Therefore, I need to configure my modem router first. How can I do that? 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > IPTV to open the configuration page. 3. Click Enable IPTV to enable this function. 4.
Chapter 8 Guest Network This function allows you to provide Wi-Fi access for guests without disclosing your main network. When you have guests in your house, apartment, or workplace, you can create a guest network for them. In addition, you can assign network authorities for guests to ensure network security, privacy, and fluency.
Chapter 8 8. 1. Guest Network Create a Network for Guests 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > Guest Network. Locate the Wireless Settings section. 3. Create 2.4GHz and 5GHz guest network according to your needs. 1 ) Enable 2.4GHz Wireless or 5GHz Wireless or enable both according to your needs. 2 ) Set an easy-to-identify SSID.
Chapter 8 Guest Network 3. Assign network authorities and bandwidth according to your needs. • Allow Guests to Access Each Other • Allow Guests to Access My Local Network • Allow Guests to Access My USB Storage Sharing Select this check box to allow the clients in your guest network to access each other’s files. Select this check box to allow the clients in your guest network to access your local network, not just the internet.
Chapter 9 USB Settings This chapter describes how to use the USB ports to share files, media and a printer from the USB storage devices over your home network locally, or remotely through the internet. The modem router supports USB external flash drives, hard drives and USB printers.
USB Settings Chapter 9 9. 1. Access the USB Storage Device Insert your USB storage device into the modem router’s USB port and then access files stored there locally or remotely. Tips: • If you use USB hubs, make sure no more than 4 devices are connected to the modem router. • If the USB storage device requires using bundled external power, make sure the external power has been connected. • If you use a USB hard drive, make sure its file system is FAT32 or NTFS.
USB Settings Chapter 9 ¾¾ Method 2: Open the Windows Explorer (or go to Computer) and type the server address \\tplinkmodem.net or ftp://tplinkmodem.net in the address bar, then press Enter. Windows computer ¾¾ Method 3: Open a web browser and type the server address http:// tplinkmodem.net:8082 in the address bar, then press Enter. Tips: You can also use the SFTP method to access the USB storage device. 1 ) Select Go > Connect to Server 2 ) Type the server address smb://tplinkmodem.
USB Settings Chapter 9 9. 1. 2. Access the USB Device Remotely You can access your USB disk outside the local area network. For example, you can: • Share photos and other large files with your friends without logging in to (and paying for) a photo-sharing site or email system. • Get a safe backup for the materials for a presentation. • Save and remove the files on your camera’s memory card during your travels. Note: If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.
USB Settings Chapter 9 ¾¾ Method 1: 1 ) Open the Windows Explorer (or go to Computer, only for Windows users) or open a web browser. 2 ) Type the server address in the address bar: Type in ftp://: (such as ftp://59.40.2.243:21). If you have specified the domain name of the modem router, you can also type in ftp://: (such as ftp:// MyDomainName:21) 3 ) Press Enter on the keyboard.
USB Settings Chapter 9 9. 1. 3. Customize the Access Settings By default, all the network clients can access all folders on your USB disk. You can customize your sharing settings by setting a sharing account, sharing specific contents and setting a new sharing address on the modem router’s web management page. 1. Visit http://tplinkmodem.net, then log in with your TP-Link ID or the password you set for the modem router. 2. Go to Advanced > USB Sharing > USB Storage Device page.
Chapter 9 USB Settings 2. Select the Volume Name and Folder Path, then enter a Folder Name as you like. 3. Decide the way you share the folder: • • • Enable Authentication: Select to enable authentication for this folder sharing, and you will be required to log in to the Sharing Account to access the USB disk. Refer to To Set up Authentication for Data Security to learn more. Enable Write Access: If you tick this check box, network clients can modify this folder.
Chapter 9 USB Settings ¾¾ To Set up Authentication for Data Security You can set up authentication for your USB device so that network clients will be required to enter the username and password when accessing the USB disk. 1. Under Sharing Account, choose Use Default Account or Use New Account. The user name and password are both admin for the default account. If your choose Use New Account, you have to customize the username and a password.
USB Settings Chapter 9 Note: Due to Windows credential mechanism, you might be unable to access the USB disk after changing Authentication settings. Please log out from the Windows and try to access again. Or you can change the address of the USB disk by referring to To Customize the Address of the USB Disk. 9. 2. Media Sharing Media Sharing allows you to view photos, play music and watch movies stored on the USB disk directly from DLNA-supported devices, such as your computer, tablet or games console.
USB Settings Chapter 9 • Go to Computer > Network, then click the Media Server Name (Archer_ model number by default) in the Media Devices section. Note: Here we take Windows 7 as an example. Windows Computer Smart device 9. 3. • Use a third-party DLNA-supported player. Printer Sharing The feature of Printer Sharing helps you share a printer with different computers connected to the modem router. Note: Printers unlisted on this page may be incompatible with the modem router: http://www.tp-link.
USB Settings Chapter 9 3. Install the TP-Link USB Printer Controller Utility TP-Link USB Printer Controller Utility helps you access the shared printer. Download and install the utility on each computer that needs printer service. 1 ) Visit http://www.tp-link.com/app/usb/. 2 ) Click PC Utility (for Windows users) or Mac Utility to download the installation file and decompress it.
USB Settings Chapter 9 3 ) Click the Auto-Connect for printing tab to pull down a list, then select Set AutoConnect Printer. Windows Mac 4 ) Select the printer you share, then click Apply.
USB Settings Chapter 9 Mac 5 ) You will see the printer marked as Auto-Connect Printer. Now you can print with this printer. Windows Mac Tips: The Print Server also allows different clients to share the scan feature of MFPs (Multi-Function Printers). To scan with TP-Link USB Printer Controller, right-click the printer and select Network Scanner. Then, a scanning window will pop up. Finish the scanning process by following on-screen instructions.
USB Settings Chapter 9 9. 4. 3G/4G Settings The modem router can be used as a 3G/4G wireless router if you have a 3G/4G USB modem. There are two ways to use your 3G/4G network: • As a backup solution for internet access • As the only way to access the internet 9. 4. 1. As a Backup Solution for Internet Access Using 3G/4G network as a backup solution for internet access, your modem router will be directly connected to the 3G/4G network when the original network service fails.
USB Settings Chapter 9 Note: The 3G/4G USB modem will not be identified if it is incompatible with the modem router. Find the 3G/4G Compatibility List on the web page: http://www.tp-link.com/en/comp-list.html. If your USB modem is incompatible, contact our technical support. 5. Verify that the modem router has correctly recognized your Mobile ISP. When your Mobile ISP is correct, you have successfully set 3G/4G network as a backup solution for internet access.
Chapter 9 USB Settings 6. Verify that your 3G/4G USB Modem is successfully detected. Note: If your 3G/4G USB modem is incompatible with the modem router, it will not be identified. Find the 3G/4G Compatibility List on the web page: http://www.tp-link.com/en/comp-list.html. If your USB modem is incompatible, contact our technical support. 7. Verify that the modem router has correctly recognized your Mobile ISP.
Chapter 10 Parental Controls This function allows you to block inappropriate, explicit and malicious websites and limit internet access during specified time periods.
Chapter 10 I want to: Parental Controls Control what types of websites my children or other home network users can visit and the time of day they are allowed to access the internet. For example, I want to allow my children’s devices (for example, a computer or a tablet) to access only www.tp-link.com and wikipedia.org from 18:00 (6PM) to 22:00 (10PM) on weekdays and not other time. How can I do that? 1. Visit http://tplinkmodem.
Chapter 10 Parental Controls 4. Click Scan, and add the device to be controlled. Or, enter the Device Name and MAC Address manually. 5. Click the icon to set the Effective Time. Drag the cursor over the appropriate cell(s) and click OK. 6. Enter a Description for the entry. 7. Select the check box to enable this entry and click OK. 8. Enable Content Restriction and select the restriction mode.
Chapter 10 Parental Controls 1 ) In Blacklist mode, the controlled devices cannot access any websites containing the specified keywords during the Effective Time period. 2 ) In Whitelist mode, the controlled devices can only access websites containing the specified keywords during the Effective Time period. 9. Click Add a New Keyword. You can add many keywords for both Blacklist and Whitelist. Below are some sample entries to allow access. 1 ) Enter a web address (for example, www.tp-link.
Chapter 11 Network Security This chapter guides you on how to protect your home network from unauthorized users by implementing these three network security functions. You can block or allow specific client devices to access your wireless network using MAC Filtering, or using Access Control for wired and wireless networks, or you can prevent ARP spoofing and ARP attacks by using IP & MAC Binding.
Chapter 11 Network Security 11. 1. Firewall & DoS Protection The SPI (Stateful Packet Inspection) Firewall and DoS (Denial of Service) Protection protect the router from cyber attacks. The SPI Firewall can prevent cyber attacks and validate the traffic that is passing through the router based on the protocol. This function is enabled by default, and it’s recommended to keep the default settings.
Chapter 11 Network Security 2. The protection will be triggered immediately when the number of packets exceeds the preset threshold value, and the vicious host will be displayed in the Blocked DoS Host List. 11. 2. Service Filtering With Service Filtering, you can prevent certain users from accessing the specified service, and even block internet access completely. 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2.
Chapter 11 Network Security 5. Select a Service Type from the drop-down list and the following four fields will be auto-populated. Select Custom when your desired service type is not listed, and enter the information manually. 6. Specify the IP address(es) that this filtering rule will apply to. 7. Click Save. Note: If you want to disable this entry, click the icon. 11. 3.
Chapter 11 Network Security 3. Select the access mode to either block (recommended) or allow the device(s) in the list. To block specific device(s) 1 ) Select Blacklist and click Save. 2 ) Select the device(s) to be blocked in the Devices Online table. 3 ) Click Block above the Devices Online table. The selected devices will be added to Devices in Blacklist automatically. To allow specific device(s) 1 ) Select Whitelist and click Save. 2 ) Click Add.
Chapter 11 Network Security 3 ) Enter the Device Name and MAC Address. (You can copy and paste the information from Devices Online table if the device is connected to your network.) Done! 4 ) Click OK. Now you can block or allow specific client devices to access your network (via wired or wireless) using the Blacklist or Whitelist. 11. 4. IP & MAC Binding IP & MAC Binding, namely, ARP (Address Resolution Protocol) Binding, is used to bind a network device’s IP address to its MAC address.
Chapter 11 Network Security 2 ) Click Bind to add to the Binding List. To bind the unconnected device 1 ) Click Add. 2 ) Enter the MAC address and IP address that you want to bind. 3 ) Select the check box to enable the entry and click OK. Done! Enjoy the internet without worrying about ARP spoofing and ARP attacks. 11. 5. IPv6 Firewall IPv6 Firewall protects your IPv6 network by preventing access from the internet.
Chapter 11 Network Security 4. Select an interface name from the drop-down list. Interface names are names of the internet connections you have set up. 5. Click Scan to select a service from the list to automatically populate the Port field with an appropriate port number. It is recommended to keep the default Port if you are unsure about which one to use. If the service is not listed, manually enter the Service Type and the Port number (e.g., 21 or 21-25). 6.
Chapter 12 NAT Forwarding Modem router’s NAT (Network Address Translation) feature makes the devices in the LAN use the same public IP address to communicate in the internet, which protects the local network by hiding IP addresses of the devices. However, it also brings about the problem that external host cannot initiatively communicate with the specified device in the local network.
Chapter 12 NAT Forwarding 12. 1. Translate Address and Port by ALG ALG (Application Layer Gateway) allows customized NAT (Network Address Translation) traversal filters to be plugged into the gateway to support address and port translation for certain application layer “control/data” protocols: FTP, TFTP, H323 etc. Enabling ALG is recommended. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. Go to Advanced > NAT Forwarding > ALG.
Chapter 12 NAT Forwarding • RTSP ALG: If enabled, it allows RTSP (Real-Time Stream Protocol) clients and servers to transfer data via NAT. 12. 2. Share Local Resources over the Internet by Virtual Server When you build up a server in the local network and want to share it on the internet, Virtual Server can realize the service and provide it to the internet users. At the same time virtual server can keep the local network safe as other services are still invisible from the internet.
Chapter 12 NAT Forwarding 4. Click Scan, and choose HTTP. The external port, internal port and protocol will be automatically filled with contents. Enter the PC’s IP address 192.168.1.100 in the Internal IP field. 5. Click OK to save the settings. Done! Tips: 1. It is recommended to keep the default settings of Internal Port and Protocol if you are not clear about which port and protocol to use. 2.
Chapter 12 NAT Forwarding address of the host. When the data from the internet returns to the external ports, the modem router can forward them to the corresponding host. Port triggering is mainly applied to online games, VoIPs and video players. Common applications include MSN Gaming Zone, Dialpad, Quick Time 4 players, and so on. Follow the steps below to configure the port triggering rules: 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2.
Chapter 12 NAT Forwarding all ports opened. When you are not clear about which ports to open in some special applications, like IP camera and database software, you can set the PC to be a DMZ host. Note: DMZ is most applicable when you don’t know which ports to open. When it is enabled, the DMZ host is totally exposed to the internet, which may bring some potential safety hazard. If DMZ is not in use, please disable it in time.
Chapter 12 NAT Forwarding seamless connection of the network. You may need to enable the UPnP if you want to use applications such as multiplayer gaming, peer-to-peer connections, real-time communication (for example, VoIP or telephone conference), or remote assistance. Tips: 1. UPnP is enabled by default in this modem router. 2. Only the application supporting UPnP protocol can use this feature. 3. UPnP feature needs the support of operating system (e.g. Windows Vista/ Windows 7/ Windows 8, etc.
Chapter 13 VPN Server The VPN (Virtual Private Networking) Server allows you to access your home network in a secured way through the internet when you are out of the house. The router offers three ways to setup VPN connection: OpenVPN, PPTP (Point to Point Tunneling Protocol) VPN and IPSec (Internet Protocol Security) VPN. OpenVPN is somewhat complex but with greater security and more stability. It is suitable for restricted environment, such as campus network and company intranet.
Chapter 13 VPN Server 13. 1. Use OpenVPN to Access Your Home Network In an OpenVPN connection, the home network can act as a server, and the remote device can access the server through the router which acts as an OpenVPN Server gateway. To use the VPN feature, you should enable OpenVPN Server on your router, install and run VPN client software on the remote device. Please follow the steps below to set up an OpenVPN connection. ¾¾ Step 1. Set up OpenVPN Server on Your Router 1. Visit http://tplinkmodem.
Chapter 13 VPN Server 6. Select your Client Access type. Select Home Network Only if you only want the remote device to access your home network; select Internet and Home Network if you also want the remote device to access the internet through the VPN Server. 7. Click Save. 8. Click Generate to get a new certificate. Note: If you have already generated one, please skip this step, or click Generate to update the certificate. 9.
Chapter 13 VPN Server Note: Before you enable VPN Server, we recommend you configure Dynamic DNS Service (recommended) or assign a static IP address for router’s WAN port and synchronize your System Time with internet. 3. In the Client IP Address field, enter the range of IP addresses (up to 10) that can be leased to the devices by the PPTP VPN server. 4. Enter the Username and Password to authenticate clients to the PPTP VPN server. 5. Click Save. ¾¾ Step 2.
Chapter 13 VPN Server 4. Select Use my Internet connection (VPN). 5. Enter the internet IP address of the router (for example: 218.18.1.73) in the Internet address field. Click Next.
Chapter 13 VPN Server 6. Enter the Username and Password you have set for the PPTP VPN server on your router, and click Connect. 7. The PPTP VPN connection is created and ready to use.
Chapter 13 VPN Server 13. 3. Use IPSec VPN to Access Your Home Network IPSec VPN is used to create a VPN connection between local and remote networks. To use IPSec VPN, you should check that both local and remote routers support IPSec VPN feature. Then, follow the steps below to set up an IPSec VPN connection. 1. The typical VPN topology is here. Site A refers to local network, and Site B refers to the remote network that is to be connected.
Chapter 13 VPN Server 3 ) In the IPSec Connection Name column, specify a name. 4 ) In the Remote IPSec Gateway (URL) column, Enter Site B’s WAN IP address. 5 ) Configure Site A’s LAN. In the Tunnel access from local IP addresses column, we take Subnet Address as an example. Input the LAN IP range of Site A in the IP Address for VPN column, and input Subnet Mask of Site A. 6 ) Configure Site B’s LAN. In the Tunnel access from remote IP addresses column, we take Subnet Address as an example.
Chapter 13 VPN Server 8 ) Enter the Pre-Shared Key for IKE authentication. Then keep Perfect Forward Secrecy enabled. Note: Make sure Site A and Site B use the same key. 9 ) Leave the Advanced Settings as default value. Then click Save. Note: The Status column is Down after the configuration, and it will change to UP only when Site A and Site B are communicating via the VPN connection. 3. Configuration on Site B (remote network).
Chapter 13 VPN Server Note: 1. The product supports a maximum of ten simultaneous connections. 2. If one of the site has been offline for a while, for example, if Site A has been disconnected, on Site B you need to click Disable and then click Enable after Site A back on line in order to re-establish the IPSec tunnel.
Chapter 14 Specify Your Network Settings This chapter introduces how to change the default settings or adjust the basic configuration of the modem router using the web management page.
Chapter 14 Specify Your Network Settings 14. 1. LAN Settings 14. 1. 1. Change the LAN IP Address The modem router is preset with a default LAN IP 192.168.1.1, which you can use to log in to its web management page. The LAN IP address together with the Subnet Mask also defines the subnet that the connected devices are on. If the IP address conflicts with another device in your local network or your network requires a specific IP subnet, you can change it. Follow the steps below to change your IP address.
Chapter 14 Specify Your Network Settings 14. 1. 2. Use the Modem Router as a DHCP Server You can configure the modem router to act as a DHCP server to assign IP addresses to its clients. To use the DHCP server function of the modem router, you must configure all computers on the LAN to obtain an IP Address automatically. Follow the steps below to configure DHCP server. 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2.
Chapter 14 Specify Your Network Settings 14. 1. 3. Reserve LAN IP Addresses You can view and add a reserved address for a client. When you specify an IP address for a device on the LAN, that device will always receive the same IP address each time when it accesses the DHCP server. If there are some devices in the LAN that require permanent IP addresses, please configure Address Reservation on the router for the purpose. Follow the steps below to reserve an IP address for your device. 1.
Chapter 14 Specify Your Network Settings 14. 2. 1. Configure the RADVD Address Type 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > Network > LAN Settings. 3. Select IPv6 to configure IPv6 LAN parameters. Note: If you have created an interface group, you can configure IPv6 LAN settings for the default interface group only. 1 ) Select the RADVD address type to make the modem router assign IPv6 address prefixes to hosts.
Chapter 14 Specify Your Network Settings 1 ) Select the DHCPv6 Server address type to make the modem router assign IPv6 addresses to hosts. 2 ) Specify the Start/End IPv6 Address for the IPv6 suffixes. The modem router will generate IPv6 addresses within the specified range. 3 ) Keep Leased Time as the default value. 4 ) Keep Site Prefix Type as the default value Delegated. If your ISP has provided a specific IPv6 site prefix, select Static and enter the prefix.
Chapter 14 Specify Your Network Settings ¾¾ To enable or disable the wireless function: Enable the 2.4 GHz or 5GHz Wireless Network. If you don’t want to use the wireless function, just deselect the box. If you disable the wireless function, all the wireless settings won’t be effective. ¾¾ To change the wireless network name (SSID) and wireless password: Enter a new SSID using up to 32 characters. The value is case-sensitive.
Chapter 14 Specify Your Network Settings • 802.11a/n/ac mixed (5GHz): Select if you are using a mix of 802.11a, 802.11n and 802.11ac wireless clients. It is strongly recommended that you select 11a/n/ac mixed. Channel: Select the channel you want to use from the drop-down list. This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.
Chapter 14 Specify Your Network Settings 3. Click Start WPS on the page. 4. Press the WPS button of the client device directly. 5. The wireless LEDs of the router flash for about 2 minutes during the WPS process. 6. When the wireless LEDs are on, the client device has successfully connected to the modem router. Method 3: Enter the modem router’s PIN on your client device Use this method if your client device asks for the modem router’s PIN. 1. Visit http://tplinkmodem.
Chapter 14 Specify Your Network Settings Method 4: Enter the client device’s PIN on the modem router 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > Wireless > WPS page. Click Method Two--PIN. 3. Select Client’s PIN. 4. Enter the client device’s PIN in the field. Then click the Connect button. 5. Connect successfully will appear on the above screen, which means the client device has successfully connected to the modem router.
Chapter 14 Specify Your Network Settings 4. Click Add to set the Wireless Off Time, and click Save to save the settings. Note: 1. Make sure that the time of the router is correct before using this function. For details, refer to Set System Time. 2. The wireless LED (2.4GHz , 5GHz) will turn off if the corresponding wireless network is disabled. 3. The wireless network will be automatically turned on after the time period you set. 14. 3. 4.
Chapter 14 Specify Your Network Settings Tips: You can also see the wireless details by clicking the router icon on Basic> Network Map. ¾¾ To view the detailed information of the connected wireless clients: 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > Wireless > Statistics page. 3.
Chapter 14 Specify Your Network Settings • Beacon Interval: Enter a value between 25 and 1000 in milliseconds to determine the duration between which beacon packets are broadcasted by the router to synchronize the wireless network. The default is 100 milliseconds. • RTS Threshold: Enter a value between 1 and 2346 to determine the packet size of data transmission through the router. By default, the RTS (Request to Send) Threshold size is 2346.
Chapter 14 Specify Your Network Settings the DDNS (Dynamic Domain Name Server) feature on the router to allow you and your friends to access your router and local servers (FTP, HTTP, etc.) using domain name, in no need of checking and remembering the IP address. Note: DDNS does not work if the ISP assigns a private WAN IP address (such as 192.168.1.x) to the modem router. To set up DDNS, please follow the instructions below: 1. Visit http://tplinkmodem.
Chapter 14 How can I do that? Specify Your Network Settings 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > Network > Interface Grouping to open the configuration page where some interfaces can be grouped together. Click Add to create a group. 3. Name the group. 4. Check the boxes of LAN1 and LAN3 in Available LAN. Here Wi-Fi 2.4G network and Wi-Fi 5G network are viewed as a LAN interface respectively. 5.
Chapter 14 Specify Your Network Settings For example, in a small office, my PC can surf the internet, but I also want to visit my company’s server. Now I have a switch and another router. I connect the devices as shown in the following figure so that the physical connection between my PC and my company’s server is achieved. To surf the internet and visit my company’s network at the same time, I need to configure the static routing. Modem router Company’s server Router 2 WAN: 172.30.30.100 LAN: 192.
Chapter 14 Specify Your Network Settings • Network Destination: The destination IP address that you want to assign to a static route. This IP address cannot be on the same subnet with the WAN IP or LAN IP of the router. In the example, the IP address of the company network is the destination IP address, so here enters 172.30.30.1. • Subnet Mask: Determines the destination network with the destination IP address. If the destination is a single IP address, enter 255.255.255.
Chapter 14 Specify Your Network Settings 14. 7. Set Up the IPv6 Tunnel The IPv6 Tunnel feature helps you obtain IPv6 resources based on an IPv4 WAN connection or vice versa. IPv6 Tunnel is a transition mechanism that allows isolated IPv6 hosts and networks to reach each other over IPv4-only infrastructure before IPv6 completely supplants IPv4. It is a temporary solution for networks that do not support native dual-stack, where both IPv6 and IPv4 run independently.
Chapter 14 Specify Your Network Settings 14. 7. 2. Specify the 6rd Tunnel with Parameters Provided by Your ISP I want to: Specify the 6rd tunnel with the parameters provided by my 6rd tunnel service provider. How can I do that? 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > Network > IPv6 Tunnel. 3. Tick the check box, select 6rd as the tunneling mechanism and select a WAN connection from the drop-down list. 4.
Chapter 15 Administrate Your Network This chapter introduces how to change the system settings and administrate your modem router’s network.
Chapter 15 Administrate Your Network 15. 1. Set System Time System time is the time displayed while the modem router is running. The system time you configure here will be used for other time-based functions like Parental Controls and Wireless Schedule. You can manually set how to get the system time. Follow the steps below to set your system time. 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the modem router. 2.
Chapter 15 Administrate Your Network 15. 2. Control LEDs The router‘s LEDs indicate router’s activities and status. You can turn on or turn off the LEDs either from the web management page or by pressing the LED button. 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > System Tools > LED Control and enable Night Mode. 3. Specify a time period in the Night Mode Period as needed. 4.
Chapter 15 Administrate Your Network 15. 3. 1. Online Upgrade 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2. If there’s any firmware update available for your router, the update icon will display on the top-right corner of the page. Click the icon to go to the Firmware Upgrade page. Alternatively, you can go to Advanced > System Tools > Firmware Upgrade, and click Check for Upgrades to see if there’s any new firmware.
Chapter 15 Administrate Your Network 6. Wait a few moments for the upgrading and rebooting. 15. 4. Back up and Restore Configuration Settings The configuration settings are stored as a configuration file in the router. You can back up the configuration file to your computer for future use and restore the modem router to a previous settings from the backup file when needed. Moreover, if needed you can erase the current settings and reset the modem router to the default factory settings.
Chapter 15 Administrate Your Network 3. Click Restore to restore all configuration settings to default values, except your login and TP-Link ID information. Click Factory Restore to reset the modem router. 4. Wait for the reset process to complete, and then the modem router will automatically reboot. Note: 1. During the resetting process, do not turn off the modem router. 2. We strongly recommend you back up the current configuration settings before resetting the modem router. 15. 5.
Chapter 15 Administrate Your Network 2. Go to Advanced > System Tools > Administration page. Locate the Local Management section. 3. Keep the Port as the default setting. Enable Management over HTTPS and keep the Port for HTTPS as the default setting. Enter the IP address or MAC address of the local device to manage the modem router. 4. Click Save. Now, you can manage the modem router over both HTTP (http://tplinkmodem.net) and HTTPS (https://tplinkmodem.net).
Chapter 15 Administrate Your Network 3. Tick the check box to enable Remote Management. Enable Remote Management via HTTPS to allow for HTTPS connection. Keep the Port as the default setting. 4. Set the client device allowed for remote management. Select All to allow all remote devices to manage the modem router. If you just want to allow a specific device to manage the modem router, select Only the Following IP/MAC Address and enter the IP/MAC address of the remote device. 5. Click Save.
Chapter 15 Administrate Your Network 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2. Click Advanced > System Tools > System Log page. ¾¾ To view the system logs: You can view specific system logs by selecting the log Type and Level. Click Refresh to refresh the log list. ¾¾ To save the system logs: You can choose to save the system logs to your local computer or a remote server. Click Save Log to save the logs in a txt file to your computer.
Chapter 15 Administrate Your Network • Save Remotely: Select this option to send the system log to a remote server, select the minimum level of system log to be saved from the drop-down list and enter the information of the remote server. If the remote server has a log viewer client or a sniffer tool implemented, you can view and analyze the system log remotely in real-time. 15. 9.
Chapter 15 Administrate Your Network 15. 10. CWMP Settings The modem router supports CWMP (CPE WAN Management Protocol), also called TR-069. This collects information, performs diagnostics and configures the devices automatically via ACS (Auto-Configuration Server). 1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > System Tools > CWMP Settings page.
Chapter 15 Administrate Your Network • CWMP: Toggle On to enable the CWMP (CPE WAN Management Protocol) feature. • Inform: Enable this feature to send an Inform message to the ACS (Auto Configuration Server) periodically. • Inform Interval: Enter the time interval in seconds when the Inform message will be sent to the ACS. • ACS URL: Enter the web address of the ACS which is provided by your ISP. • ACS Username/Password: Enter the username/password to log in to the ACS server.
Chapter 15 Administrate Your Network • Get RPC methods: Click to get the methods to support CWMP. Click Save to make the settings effective. 15. 11. SNMP Settings SNMP (Simple Network Management Protocol) is widely applied in the computer networks of today, and is used for ensuring the transmission of the management information between two nodes. In this way, network administrators can easily search and modify the information on any node on the network.
Chapter 15 Administrate Your Network • SNMP Agent for WAN: Toggle On to allow management from the WAN side using SNMP. • Read-only Community: Displays the default public community string that protects the router from unauthorized access. • Write Community: Displays the default write community string that protects the router from unauthorized changes. • System Name: Displays the administratively-assigned name for this managed device.
Appendix: Troubleshooting T1. How do I restore my modem router’s configuration to its factory default settings? With the modem router powered on, press and hold down the Reset button on the modem router for 10 seconds until all LEDs turn on momentarily, then release the button. Note: Once the modem router is reset, the current configuration settings will be lost and you will need to re-configure the modem router. T2.
4 ) Click LAN settings, deselect the following three options and click OK; 5 ) Go to Advanced > Restore advanced settings, click OK to save the settings.
• • Change a web browser or computer and log in again. Reset the modem router to factory default settings. Refer to Back up and Restore Configuration Settings for detailed information. Open a web browser and log in again. If login fails, please contact our Technical Support. T4. What should I do if I cannot access the internet? 1. Ensure all connections are secure, including telephone lines, Ethernet cables and power adapters. 2.
6. Please contact our Technical Support if the problem persists. T5. How do I clone a MAC address? You can manually change the MAC address of the modem router. It is helpful when your internet access account provided by your ISP is bound to one specific MAC address, in other words, your ISP just permits only one computer with the authenticated MAC address to access the internet. In this case, you can use MAC Clone to allow more computers to access the internet via the same account. 1.
6 ) Click OK. • For Windows 7/8/8.1/10: 1 ) Right-click the Network icon on the system tray and select Open Network and Sharing Center > Change adapter settings. 2 ) Right-click your network connection (wired or wireless) and select Properties. 3 ) Double-click Internet Protocol Version 4 (TCP/IPv4). 4 ) Select both Obtain an IP address automatically and Obtain DNS server address automatically, then click OK. 5 ) Click OK again to save your configuration.
¾¾ If you can find your wireless network but fail to connect, follow the steps below: 1. Authentication problem: Network Security Key Mismatch. 1 ) Sometimes you will be asked to type in a PIN number when you connect to the wireless network for the first time. This PIN number is different from the Wireless Password/Network Security Key, usually you can only find it on the label of your modem router.
4 ) Connect to wireless network. 2. Windows was unable to connect to XXXX /Cannot join this network/Taking longer than usual to connect to this network. 1 ) Check the wireless signal strength of your network, if it is weak (1~3 bars), please move the router closer and try again; 2 ) Change the wireless Channel of the router to 1,6,or 11 to reduce interference from other networks; 3 ) Re-install or update the driver for your wireless adapter of the computer; 4 ) Connect to wireless network.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-Link Technologies Co., Ltd. Copyright © 2017 TP-Link Technologies Co., Ltd.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. OPERATING FREQUENCY(the maximum transmitted power) 2412MHz—2472MHz (20dBm) 5180MHz—5240MHz (23dBm) EU declaration of conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC and 2011/65/EU.
For EU/EFTA, this product can be used in the following countries: AT EE IE NL BE ES IS NO BG FI IT PL CH FR LI PT CY GB LT RO CZ GR LU SE DE HR LV SI DK HU MT SK Explanation of the symbols on the product label Symbol DC voltage Explanation RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE).
