TL-WR1043ND 300Mbps Wireless N Gigabit Router REV: 2.4.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device has been designed to operate with the antennas listed below, and having a maximum gain of 5 dBi. Antennas not included in this list or having a gain greater than 5 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.
NCC Notice & BSMI Notice 注意！ 依據 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻 率、加大功率或變更原設計之特性或功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立 即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率 射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。 減少電磁波影響，請妥適使用。 安全諮詢及注意事項 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 注意防潮，請勿將水或其他液體潑灑到本產品上。 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。 Продукт сертифіков
This product can be used in the following countries: AT BG BY CA CZ DE DK EE ES FI FR GB GR HU IE IT LT LV MT NL NO PL PT RO RU SE SK TR UA US
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 300Mbps Wireless N Gigabit Router Model No.
CONTENTS Package Contents ............................................................................................................................. 1 Chapter 1. Introduction ................................................................................................................... 2 1.1 Overview of the Router ................................................................................................... 2 1.2 Conventions ....................................................................
4.7.3 4.8 4.9 Address Reservation......................................................................................... 45 USB Settings................................................................................................................. 46 4.8.1 Storage Sharing ................................................................................................ 46 4.8.2 FTP Server ........................................................................................................ 48 4.
4.17.3 No-ip.com DDNS .............................................................................................. 90 4.18 System Tools................................................................................................................. 91 4.18.1 Time Setting ...................................................................................................... 92 4.18.2 Diagnostic ......................................................................................................... 93 4.18.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Package Contents The following items should be found in your package: TL-WR1043ND 300Mbps Wireless N Gigabit Router DC Power Adapter for TL-WR1043ND 300Mbps Wireless N Gigabit Router Quick Installation Guide Ethernet Cable Resource CD for TL-WR1043ND 300Mbps Wireless N Gigabit Router, including: • This Guide • Other Helpful Information Note: Make sure that the package contains the above items.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Chapter 1. Introduction 1.1 Overview of the Router The TL-WR1043ND 300Mbps Wireless N Gigabit Router integrates 4-port Switch, Firewall, NAT-router and Wireless AP. The 300Mbps Wireless N Gigabit Router delivers exceptional range and speed, which can fully meet the need of Small Office/Home Office (SOHO) networks and the users demanding higher networking performance.
TL-WR1043ND 300Mbps Wireless N Gigabit Router 1.2 Conventions The router or TL-WR1043ND mentioned in this guide stands for TL-WR1043ND 300Mbps Wireless N Gigabit Router without any explanation. 1.3 Main Features Complies with IEEE 802.11n to provide a wireless data rate of up to 300Mbps. One 10/100/1000M Auto-Negotiation RJ45 Internet port, four 10/100/1000M Auto-Negotiation RJ45 Ethernet ports, supporting Auto MDI/MDIX.
TL-WR1043ND 300Mbps Wireless N Gigabit Router 1.4 Panel Layout 1.4.1 The Front Panel Figure 1-1 Front Panel sketch The router’s LEDs and the WPS button are located on the front panel (View from left to right). Name (Power) (System) (Wireless ) (Internet) (Ethernet) (WPS) (USB) Status Indication Off Power is off. On Power is on. On The router is initializing or maybe has a system error. Flashing The router is working properly. Off The router has a system error.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Note: After a device is successfully added to the network by WPS function, the WPS LED will keep on for about 5 minutes and then turn off. 1.4.2 The Rear Panel Figure 1-2 Rear Panel sketch The following parts are located on the rear panel (View from left to right). Wireless On/Off: The switch for the wireless function. Ethernet (1, 2, 3, 4): These ports (1, 2, 3, 4) connect the router to the local PC(s).
TL-WR1043ND 300Mbps Wireless N Gigabit Router LED becomes quick-flash from slow-flash. And then release the button and wait the router to reboot to its factory default settings. Wireless antenna: To receive and transmit the wireless data.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Chapter 2. Connecting the Router 2.1 System Requirements Broadband Internet Access Service (DSL/Cable/Ethernet) One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the router is connected directly to the Ethernet.) PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors TCP/IP protocol on each PC Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari 2.
TL-WR1043ND 7. 300Mbps Wireless N Gigabit Router Power on your PC and Cable/DSL Modem.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your 300Mbps Wireless N Gigabit Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default domain name of the 300Mbps Wireless N Gigabit Router is http://tplinklogin.net, the default IP address is 192.168.0.1, and the default Subnet Mask is 255.255.255.0. These values can be changed as you desire.
TL-WR1043ND 300Mbps Wireless N Gigabit Router If the result displayed is similar to the Figure 3-2, it means the connection between your PC and the router failed. Figure 3-2 Failure result of Ping command Please check the connection following these steps: 1. Is the connection between your PC and the router correct? Note: The 1/2/3/4 LEDs of Ethernet ports which you link to on the router and LEDs on your PC's adapter should be lit. 2.
TL-WR1043ND 1. 300Mbps Wireless N Gigabit Router To access the configuration utility, open a web-browser and type the default address http://tplinklogin.net in the address field of the browser. Figure 3-3 Login the Router After a moment, a login window will appear, similar to the Figure 3-4. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key.
TL-WR1043ND Figure 3-6 300Mbps Wireless N Gigabit Router Choose WAN Connection Type The router provides Auto-Detect function and supports five popular ways Dynamic IP, Static IP, PPPoE, L2TP/Russian L2TP and PPTP/Russian PPTP to connect to the Internet. It’s recommended that you make use of the Auto-Detect function. If you are sure of what kind of connection type your ISP provides, you can select the very type and click Next to go on configuring. 1.
TL-WR1043ND 300Mbps Wireless N Gigabit Router IP Address - This is the WAN IP address as seen by external users on the Internet (including your ISP). Your ISP will provide you with the IP address you need to enter here. Enter the IP address into the field. Subnet Mask - The Subnet Mask is used for the WAN IP address. Your IPS will provide you with the subnet mask which is usually 255.255.255.0.
TL-WR1043ND 300Mbps Wireless N Gigabit Router User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. If you have difficulty with this process, please contact your ISP. Confirm Password - Enter the password again to make sure that the password is correct. Select Static IP if IP Address/ Subnet Mask/ Gateway and DNS server address have been provided by your ISP.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Confirm Password - Enter the password again to make sure that the password is correct. Select Static IP if IP Address/ Subnet Mask/ Gateway and DNS server address have been provided by your ISP. Then please enter server IP address or domain name provided by your ISP, and also enter the corresponding parameters. Select Dynamic IP if none of the above parameters are provided. Then you just need to enter server IP address or domain name provided by your ISP.
TL-WR1043ND 300Mbps Wireless N Gigabit Router network. Considering your wireless network security, the default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each router’s MAC address). This value is case-sensitive. For example, TEST is NOT the same as test. Region - Select your region from the drop-down list. This field specifies the region where the wireless function of the router can be used.
TL-WR1043ND 300Mbps Wireless N Gigabit Router These settings are only for basic wireless parameters. For advanced settings, please refer to Section 4.6: “Wireless”. 5. Click the Next button. You will then see the Finish page. Click the Finish button to finish the Quick Setup. Figure 3-12 Quick Setup – Finish If there is something changed on the Wireless page, you will see the Finish page as shown in Figure 3-13.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Chapter 4. Configuring the Router This chapter will show each Web page's key functions and the configuration way. 4.1 Login After your successful login, you will see the 17 main menus on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions. The detailed explanations for each Web page’s key function are listed below. 4.2 Status The Status page provides the current status information about the router.
TL-WR1043ND Figure 4-1 300Mbps Wireless N Gigabit Router Router Status 4.3 Quick Setup Please refer to Section 3.2: "Quick Installation Guide." 4.4 WPS This section will guide you to add a new wireless device to an existing network quickly by WPS （Wi-Fi Protected Setup) function. a). Choose menu “WPS”, and you will see the next screen (shown in Figure 4-2 ).
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-2 WPS WPS Status - Enable or disable the WPS function here. Current PIN - The current value of the router's PIN displayed here. The default PIN of the router can be found in the label or User Guide. Restore PIN - Restore the PIN of the router to its default. Gen New PIN - Click this button, and then you can get a new random value for the router's PIN. You can ensure the network security by generating a new PIN.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-4 Add A New Device Step 2: Press and hold the WPS button of the client device. Step 3: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup process. Step 4: When the WPS LED is on, the client device has successfully connected to the router. II. Enter the client device’s PIN on the router Use this method if your client device does not have the WPS button, but has a Wi-Fi Protected Setup PIN number.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Note: 1) The WPS LED on the router will light green for five minutes if the device has been successfully added to the network. 2) The WPS function cannot be configured if the Wireless Function of the router is disabled. Please make sure the Wireless Function is enabled before configuring the WPS. 4.5 Network Figure 4-6 the Network menu There are three submenus under the Network menu (shown in Figure 4-6): WAN, LAN and MAC Clone.
TL-WR1043ND 300Mbps Wireless N Gigabit Router This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters. MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Default Gateway - Enter the gateway IP address provided by your ISP in dotted-decimal notation. MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP. Primary/Secondary DNS - (Optional) Enter one or two DNS addresses in dotted-decimal notation provided by your ISP. 3.
TL-WR1043ND 300Mbps Wireless N Gigabit Router • Dynamic IP - You can check this radio button to use Dynamic IP as the secondary connection to connect to the local area network provided by ISP. • Static IP - You can check this radio button to use Static IP as the secondary connection to connect to the local area network provided by ISP.
TL-WR1043ND Figure 4-10 300Mbps Wireless N Gigabit Router PPPoE Advanced Settings MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. Service Name/AC Name - The service name and AC (Access Concentrator) name, which should not be configured unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-11 WAN – BigPond Cable User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Auth Server - Enter the authenticating server IP address or host name. Auth Domain - Type in the domain suffix server name based on your location. e.g. NSW / ACT - nsw.bigpond.net.au VIC / TAS / WA / SA / NT - vic.bigpond.net.au QLD - qld.bigpond.net.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Connect Manually - You can click the Connect/Disconnect button to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The Internet connection can be disconnected automatically after a specified inactivity period and re-established when you attempt to access the Internet again. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Connect on Demand - You can configure the router to disconnect from your Internet connection after a specified period of inactivity (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-13 WAN –PPTP User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Dynamic IP/ Static IP - Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name. If you choose static IP and enter the domain name, you should also enter the DNS assigned by your ISP. And click the Save button. Click the Connect button to connect immediately.
TL-WR1043ND 300Mbps Wireless N Gigabit Router enter the number of minutes you want to have elapsed before your Internet connection terminates. Connect Automatically - Connect automatically after the router is disconnected. To use this option, click the radio button. Connect Manually - You can configure the router to make it connect or disconnect manually.
TL-WR1043ND Figure 4-14 300Mbps Wireless N Gigabit Router LAN MAC Address - The physical address of the router, as seen from the LAN. The value can't be changed. IP Address - Enter the IP address of your router or reset it in dotted-decimal notation (factory default: 192.168.0.1). Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.0 as the subnet mask.
TL-WR1043ND 300Mbps Wireless N Gigabit Router WAN MAC Address - This field displays the current MAC address of the Internet port. If your ISP requires you to register the MAC address, please enter the correct MAC address into this field in XX-XX-XX-XX-XX-XX format(X is any hexadecimal digit). Your PC's MAC Address - This field displays the MAC address of the PC that is managing the router.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-17 Wireless Settings Wireless Network Name (also called SSID) - Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each router’s MAC address). This value is case-sensitive. For example, TEST is NOT the same as test.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Mode - Select the desired mode. The default setting is 11bgn mixed. 11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. Select the desired wireless mode. It is strongly recommended that you set the Mode to 802.11b&g&n, and all of 802.11b, 802.11g, and 802.11n wireless stations can connect to the router.
TL-WR1043ND 300Mbps Wireless N Gigabit Router • Key type - This option should be chosen according to the AP's security configuration. It is recommended that the security type is the same as your AP's security type • WEP Index - This option should be chosen if the key type is WEP (ASCII) or WEP (HEX).It indicates the index of the WEP key. • Auth Type - This option should be chosen if the key type is WEP (ASCII) or WEP (HEX).It indicates the authorization type of the Root AP.
TL-WR1043ND 300Mbps Wireless N Gigabit Router • Version - you can choose the version of the WPA-PSK security on the drop-down list. The default setting is Automatic, which can select WPA-PSK (Pre-shared key of WPA) or WPA2-PSK (Pre-shared key of WPA) automatically based on the wireless station's capability and request. • Encryption - When WPA-PSK or WPA is set as the Authentication Type, you can select either Automatic, or TKIP or AES as Encryption.
TL-WR1043ND 300Mbps Wireless N Gigabit Router • Radius Port - Enter the port number of the Radius server. • Radius Password - Enter the password for the Radius server. • Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. WEP - It is based on the IEEE 802.11 standard. If you check this radio button, you will find a notice in red as show in Figure 4-21.
TL-WR1043ND 4.6.3 300Mbps Wireless N Gigabit Router Wireless MAC Filtering Choose menu “Wireless→Wireless MAC Filtering”, and then you can control the wireless access by configuring the Wireless MAC Address Filtering function, shown in Figure 4-22. Figure 4-22 Wireless MAC Filtering To filter wireless users by MAC Address, click Enable. The default setting is Disable. To Add a Wireless MAC Address filtering entry, click the Add New… button.
TL-WR1043ND 2. 300Mbps Wireless N Gigabit Router Enter a simple description of the wireless station in the Description field. For example: Wireless station A. 3. Status - Select Enabled or Disabled for this entry on the Status drop-down list. 4. Click the Save button to save this entry. To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2. Modify the information. 3. Click the Save button.
TL-WR1043ND 4.6.4 300Mbps Wireless N Gigabit Router Wireless Advanced Choose menu “Wireless→Wireless Advanced”, and then you can configure the advanced settings of your wireless network. Figure 4-24 Wireless Advanced Transmit Power - Here you can specify the transmit power of router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here.
TL-WR1043ND 300Mbps Wireless N Gigabit Router poor network performance since excessive packets. 2346 is the default setting and is recommended. DTIM Interval - This value determines the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Sent Packets - Packets sent by the station You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click on the Refresh button. If the numbers of connected wireless stations go beyond one page, click the Next button to go to the next page and click the Previous button to return to the previous page. Note: This page will be refreshed automatically every 5 seconds. 4.
TL-WR1043ND 300Mbps Wireless N Gigabit Router DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually. Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address. End IP Address - Specify an IP address for the DHCP Server to end with when assigning IP addresses. 192.168.0.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Assigned IP - The IP address that the router has allocated to the DHCP client. Lease Time - The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. You cannot change any of the values on this page. To update this page and to show the current attached devices, click the Refresh button. 4.7.
TL-WR1043ND Figure 4-30 300Mbps Wireless N Gigabit Router Add or Modify an Address Reservation Entry To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2. Modify the information. 3. Click the Save button.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-32 Storage Sharing Service Status - Indicates the Storage Sharing service's current status, started or stopped. You can click the Start button to start the Storage Sharing service and click the Stop button to stop it. Volume - The volume name of the USB drive the users have access to. Capacity - The storage capacity of the USB driver. Used - The used space of the USB driver. Free - The available space of the USB driver.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-34 Storage Sharing 3. Click the Start button to start the Storage Sharing service. 4. Click the Enable button in shared row to enable the disk to share. 5. Click the Disable button in shared row to disable the disk to share. 6. Click the Open the disk to visit the sharing disk. Note: 1. The router can automatically locate new USB drive. 2. The new settings will not take effect until you restart the service. 3.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-35 FTP Server Configuration Server Status - Indicates the FTP Server’s current status, started or stopped. You can click the Start button to start the FTP Server and click the Stop button to stop it. Internet Access – Indicates the current status of Internet Access. Choose Enable to enable the Internet Access and choose Disable to disable it. Service Port - The numbers of External Service Ports.
TL-WR1043ND 300Mbps Wireless N Gigabit Router 2. Click the Enable/Disable box to enable/disable internet access to FTP from Internet port. 3. Change the Service Port to specify a port for FTP Server to use. (The default is 21, do not change unless necessary.) 4. Click Add New Folder to add new folders for the FTP Server. The screen will show as Figure 4-37. Figure 4-37 Add or Modify Share Folder Display Name - You can enter a display name for the share folder.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-38 FTP Server Configuration 5. Click the Start button to start the FTP Server. Note: 1. The max share folders number is 10. If you want to share a new folder when the number has reached 10, you can delete a share folder and then add a new one. 2. The change of the FTP settings will take effect after restarting the FTP Server. 3. Currently, the maximum number of clients that FTP Server supports is two.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Name - The display name of this folder. File System - The file system type on the partition can be FAT32 or NTFS. Folder - The real full path of the specified folder. Delete - You can delete the share folder by click Delete. To set up your media server, please follow the instructions below: 1. Plug an external USB hard disk drive or USB flash drive into this router, and then the screen will appear as shown in Figure 4-40.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-42 Add New Folder Display Name - You can enter a display name for the share folder. Share entire partition - You can select this option and then the folders contained in this partition will all be shared. Folder Location- Displays the location of this folder. Select - You can select this option to share the specified folder. Folder - Name of folders that is in current path.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-43 Media Server Setting 4. Click the Scan All button to scan all the share folders immediately. You can also select the Auto-scan, at same time, select an auto scan interval time by drop-down list. In this case, the media server will auto scan the share folders. Note: The max share folders number is 6. If you want share a new folder when the numbers has been reached to be 6, you can delete a share folder and then add a new one. 4.8.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Storage Sharing and can access FTP Server while Guest has read-only access to Storage Sharing and can not access FTP Server. Figure 4-45 User Account Management Only Administrator can use a Web browser to transfer the files from a PC to the Writable shared volume on the USB drive. To add a new user account, please follow the steps below: 1. Click Add New User button, and the screen will appear as shown in Figure 4-46. 2. Self-define a User Name. 3.
TL-WR1043ND 300Mbps Wireless N Gigabit Router User Name - Type the user name that you want to give access to the USB drive. The user name must be composed of alphanumeric symbols not exceeding 15 characters in length. Password - Enter the password in the Password field. The password must be composed of alphanumeric symbols not exceeding 15 characters in length. For security purposes, the password for each user account is not displayed.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Disable Hardware NAT Control - If disabled, neither Hardware NAT feature will take effect. 4.10 Forwarding Figure 4-48 The Forwarding menu There are four submenus under the Forwarding menu (shown in Figure 4-48): Virtual Servers, Port Triggering, DMZ and UPnP. Click any of them, and you will be able to configure the corresponding function. 4.10.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Protocol - The protocol used for this application, either TCP, UDP, or All (all protocols supported by the router). Status - The status of this entry, "Enabled" means the virtual server entry is enabled. Common Service Port - Some common services already exist in the drop-down list. Modify - To modify or delete an existing entry. To setup a virtual server entry: 1. Click the Add New... button. (pop-up Figure 4-50) 2.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Click the Next button to go to the next page and click the Previous button to return to the previous page. Note: If you set the service port of the virtual server as 80, you must set the Web management port on System Tools –> Remote Management page to be any other value except 80 such as 8080. Otherwise there will be a conflict to disable the virtual server. 4.10.
TL-WR1043ND Figure 4-52 300Mbps Wireless N Gigabit Router Add or Modify a Triggering Entry Trigger Port - The port for outgoing traffic. An outgoing connection using this port will trigger this rule. Trigger Protocol - The protocol used for Trigger Ports, either TCP, UDP, or All (all protocols supported by the router). Incoming Port - The port or port range used by the remote system when it responds to the outgoing request.
TL-WR1043ND 2. 300Mbps Wireless N Gigabit Router The router records this connection, opens the incoming port or ports associated with this entry in the Port Triggering table, and associates them with the local host. 3. When necessary, the external host will be able to connect to the local host using one of the ports defined in the Incoming Ports field. Note: 1. When the trigger connection is released, the corresponding opened ports will be closed. 2.
TL-WR1043ND Figure 4-54 300Mbps Wireless N Gigabit Router UPnP Setting Current UPnP Status - UPnP can be enabled or disabled by clicking the Enable or Disable button. This feature is enabled by default. Current UPnP Settings List - This table displays the current UPnP information. • App Description - The description about the application which initiates the UPnP request. • External Port - The port which the router opened for the application. • Protocol - The type of protocol which is opened.
TL-WR1043ND 300Mbps Wireless N Gigabit Router 4.11.1 Basic Security Choose menu “Security → Basic Security”, and then you can configure the basic security in the screen as shown in Figure 4-56. Figure 4-56 Basic Security Firewall - A firewall protects your network from the outside world. Here you can enable or disable the router’s firewall. • SPI Firewall - SPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to prevent cyber attacks by tracking more state per session.
TL-WR1043ND 300Mbps Wireless N Gigabit Router ALG - It is recommended to enable Application Layer Gateway (ALG) because ALG allows customized Network Address Translation (NAT) traversal filters to be plugged into the gateway to support address and port translation for certain application layer "control/data" protocols such as FTP, TFTP, H323 etc. • FTP ALG - To allow FTP clients and servers to transfer data across NAT, click Enable.
TL-WR1043ND 300Mbps Wireless N Gigabit Router section of the packets statistics. The result of the statistics is used for analysis by SYN Flood, UDP Flood and ICMP-Flood. DoS Protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS protection function. Only when it is enabled, will the flood filters be enabled. Note: Dos Protection will take effect only when the Traffic Statistics in “System Tool → Traffic Statistics” is enabled.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-58 Local Management By default, the radio button “All the PCs on the LAN are allowed to access the Router's Web-Based Utility” is checked. If you want to allow PCs with specific MAC Addresses to access the Setup page of the Router's Web-Based Utility locally from inside the network, check the radio button “Only the PCs listed can browse the built-in web pages to perform Administrator tasks”, and then enter each MAC Address in a separate field.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-59 Remote Management Web Management Port - Web browser access normally uses the standard HTTP service port 80. This router's default remote management web port number is 80. For greater security, you can change the remote management web port to a custom port by entering that number in the box provided. Choose a number between 1 and 65534 but do not use the number of any common service port.
TL-WR1043ND Figure 4-60 300Mbps Wireless N Gigabit Router Parental Control Settings To add a new entry, please follow the steps below. 1. Click the Add New… button and the next screen will pop-up as shown in Figure 4-61.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Parental Control - Check Enable if you want this function to take effect; otherwise, check Disable. MAC Address of Parental PC - In this field, enter the MAC address of the controlling PC, or you can make use of the Copy To Above button below. MAC Address of Your PC - This field displays the MAC address of the PC that is managing this router.
TL-WR1043ND 300Mbps Wireless N Gigabit Router 2. Click “Access Control → Schedule” on the left to enter the Schedule Settings page. Click Add New... button to create a new schedule with Schedule Description is Schedule_1, Day is Sat and Time is all day-24 hours. 3. Click “Parental Control” menu on the left to go back to the Add or Modify Parental Control Entry page: 4. 1) Click Add New... button. 2) Enter 00-11-22-33-44-AA in the MAC Address of Child PC field.
TL-WR1043ND Figure 4-64 300Mbps Wireless N Gigabit Router Access Control Rule Management Enable Internet Access Control - Select the check box to enable the Internet Access Control function, so the Default Filter Policy can take effect. Rule Name - Here displays the name of the rule and this name is unique. Host - Here displays the host selected in the corresponding rule. Target - Here displays the target selected in the corresponding rule.
TL-WR1043ND 300Mbps Wireless N Gigabit Router There are two methods to add a new rule. Method One: 1. Click Setup Wizard button and the next screen will appear as shown in Figure 4-65. Figure 4-65 Quick Setup – Create a Host Entry Host Description - In this field, create a unique description for the host (e.g. Host_1). Mode - Here are two options, IP Address and MAC Address. You can select either of them from the drop-down list.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-66 Quick Setup – Create an Access Target Entry Target Description - In this field, create a description for the target. Note that this description should be unique (e.g. Target_1). Mode - Here are two options, IP Address and Domain Name. You can choose either of them from the drop-down list.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-67 Quick Setup – Create an Advanced Schedule Entry Schedule Description - In this field, create a description for the schedule. Note that this description should be unique (e.g. Schedule_1). Day - Choose Select Days and select the certain day (days), or choose Everyday. Time - Select "24 hours", or specify the Start Time and Stop Time yourself. Start Time - Enter the start time in HHMM format (HHMM are 4 numbers).
TL-WR1043ND 300Mbps Wireless N Gigabit Router Rule - In this field, create a name for the rule. Note that this name should be unique (e.g. Rule_1). Host - In this field, select a host from the drop-down list for the rule. The default value is the Host Description you set just now. Target - In this filed, select a target from the drop-down list for the rule. The default value is the Target Description you set just now.
TL-WR1043ND 300Mbps Wireless N Gigabit Router 1. Click the submenu Rule of Access Control in the left to return to the Rule List page. Select Enable Internet Access Control and choose "Allow the packets specified by any enabled access control policy to pass through the router". 2. We recommend that you click Setup Wizard button to finish all the following settings. 3. Click the submenu Host of Access Control in the left to enter the Host List page.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Modify - To modify or delete an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New… button. 2. In the Mode field, select IP Address or MAC Address. If you select IP Address, the screen shown is Figure 4-71. 1) In Host Description field, create a unique description for the host (e.g. Host_1). 2) In LAN IP Address field, enter the IP address. If you select MAC Address, the screen shown is Figure 4-72.
TL-WR1043ND 300Mbps Wireless N Gigabit Router 4. In MAC Address field, enter 00-11-22-33-44-AA. 5. Click Save to complete the settings. Then you will go back to the Host Settings page and see the following list. 4.13.3 Target Choose menu “Access Control → Target”, and then you can view and set a Target list in the screen as shown in Figure 4-73. The target list is necessary for the Access Control Rule.
TL-WR1043ND Figure 4-74 4. Add or Modify an Access Target Entry 1) In Target Description field, create a unique description for the target (e.g. Target_1). 2) In IP Address field, enter the IP address of the target. 3) Select a common service from Common Service Port drop-down list, so that the Target Port will be automatically filled. If the Common Service Port drop-down list doesn’t have the service you want, specify the Target Port manually.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Click the Next button to go to the next page, or click the Previous button to return to the previous page. For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA in the LAN to access www.google.com only, you should first follow the settings below: 1. Click Add New… button in Figure 4-73 to enter the Add or Modify an Access Target Entry page. 2. In Mode field, select Domain Name from the drop-down list. 3.
TL-WR1043ND 300Mbps Wireless N Gigabit Router 3. In Day field, select the day or days you need. 4. In Time field, you can select all day-24 hours or you may enter the Start Time and Stop Time in the corresponding field. 5. Click Save to complete the settings. Click the Delete All button to delete all the entries in the table. Click the Next button to go to the next page, or click the Previous button to return to the previous page.
TL-WR1043ND 300Mbps Wireless N Gigabit Router 4.14 Advanced Routing Figure 4-78 Advanced Routing There are two submenus under the Advanced Routing menu as shown in Figure 4-78: Static Routing List and System Routing Table. Click any of them, and you will be able to configure the corresponding function. 4.14.1 Static Routing List Choose menu “Advanced Routing → Static Routing List”, and then you can configure the static route in the next screen (shown in Figure 4-79).
TL-WR1043ND 300Mbps Wireless N Gigabit Router Subnet Mask - The Subnet Mask determines which portion of an IP Address is the network portion, and which portion is the host portion. Default Gateway - This is the IP Address of the gateway device that allows for contact between the router and the network or host. 3. Select Enabled or Disabled for this entry on the Status drop-down list. 4. Click the Save button to make the entry take effect.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Interface - This interface tells you either the Destination IP Address is on the LAN & WLAN (internal wired and wireless networks), or on the WAN (Internet). 4.15 Bandwidth Control Figure 4-82 Bandwidth Control There are two submenus under the Bandwidth Control menu as shown in Figure 4-82: Control Settings and Rules List. Click any of them, and you will be able to configure the corresponding function.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-84 Bandwidth Control Rules List Description - This is the information about the rules such as address range. Egress bandwidth - This field displays the max and mix upload bandwidth through the Internet port, the default is 0. Ingress bandwidth - This field displays the max and mix download bandwidth through the Internet port, the default is 0. Enable - This displays the status of the rule. Modify - Click Modify to edit the rule.
TL-WR1043ND 300Mbps Wireless N Gigabit Router 4.16 IP & MAC Binding Setting Figure 4-86 the IP & MAC Binding menu There are two submenus under the IP &MAC Binding menu (shown in Figure 4-86): Binding Settings and ARP List. Click any of them, and you will be able to scan or configure the corresponding function. The detailed explanations for each submenu are provided below. 4.16.
TL-WR1043ND Figure 4-88 300Mbps Wireless N Gigabit Router IP & MAC Binding Setting (Add & Modify) To add IP & MAC Binding entries, follow the steps below. 1. Click the Add New... button as shown in Figure 4-87. 2. Enter the MAC Address and IP Address. 3. Select the Bind checkbox. 4. Click the Save button to save it. To modify or delete an existing entry, follow the steps below. 1. Find the desired entry in the table. 2. Click Modify or Delete as desired on the Modify column.
TL-WR1043ND 300Mbps Wireless N Gigabit Router 4.16.2 ARP List To manage the computer, you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list, and you could also configure the items on the ARP list. This page displays the ARP List; it shows all the existing IP & MAC Binding entries (shown in Figure 4-90). Figure 4-90 ARP List 1. MAC Address - The MAC address of the controlled computer in the LAN. 2.
TL-WR1043ND 300Mbps Wireless N Gigabit Router service providers such as www.comexe.cn, www.dyndns.org, or www.no-ip.com. The Dynamic DNS client service provider will give you a password or key. 4.17.1 Comexe.cn DDNS If the dynamic DNS Service Provider you select is www.comexe.cn, the page will appear as shown in Figure 4-91. Figure 4-91 Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1. Enter the Domain Name your dynamic DNS service provider gave. 2.
TL-WR1043ND 300Mbps Wireless N Gigabit Router 4.17.2 Dyndns.org DDNS If the dynamic DNS Service Provider you select is www.dyndns.org, the page will appear as shown in Figure 4-92. Figure 4-92 Dyndns.org DDNS Settings To set up for DDNS, follow these instructions: 1. Enter the User Name for your DDNS account. 2. Enter the Password for your DDNS account. 3. Enter the Domain Name you received from dynamic DNS service provider. 4. Click the Login button to login to the DDNS service.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-93 No-ip.com DDNS Settings To set up for DDNS, follow these instructions: 1. Enter the User Name for your DDNS account. 2. Enter the Password for your DDNS account. 3. Enter the Domain Name you received from dynamic DNS service provider. 4. Click the Login button to login to the DDNS service. Connection Status - The status of the DDNS service connection is displayed here. Click Logout to log out the DDNS service.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Choose menu “System Tools”, and you can see the submenus under the main menu: Time Settings, Diagnostic, Firmware Upgrade, Factory Defaults, Backup & Restore, Reboot, Password, System Log and Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.18.
TL-WR1043ND 300Mbps Wireless N Gigabit Router End - The time to end the Daylight Saving. Select the month in the first field, the week in the second field, the day in the third field and the time in the last field. Daylight Saving Status - Displays the status whether the Daylight Saving is in use. To set time manually: 1. Select your local time zone. 2. Enter the Date in Month/Day/Year format. 3. Enter the Time in Hour/Minute/Second format. 4. Click Save. To set time automatically: 1.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure 4-97 Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic too. Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. Traceroute - This diagnostic tool tests the performance of a connection. Note: You can use ping/traceroute to test both numeric IP address or domain name.
TL-WR1043ND 300Mbps Wireless N Gigabit Router The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 4-98 Diagnostic Results Note: 1. Only one user can use the diagnostic tools at one time. 2. "Ping Count", "Ping Packet Size" and "Ping Timeout" are Ping Parameters, and "Traceroute Max TTL" is Traceroute Parameter. 4.18.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Note: 1. New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the router rather than the configuration, you can try to upgrade the firmware. 2.
TL-WR1043ND Figure 4-101 300Mbps Wireless N Gigabit Router Backup & Restore Configuration Click the Backup button to save all configuration settings as a backup file in your local computer. To upgrade the router's configuration, follow these instructions. • Click the Browse button to find the configuration file which you want to restore. • Click the Restore button to update the configuration with the file whose path is the one you have input or selected in the blank.
TL-WR1043ND 300Mbps Wireless N Gigabit Router 4.18.7 Password Choose menu “System Tools → Password”, and then you can change the factory default user name and password of the router in the next screen as shown in Figure 4-103. Figure 4-103 Password It is strongly recommended that you should change the factory default user name and password of the router, because all users who try to access the router's Web-based utility or Quick Setup will be prompted for the router's default user name and password.
TL-WR1043ND 300Mbps Wireless N Gigabit Router 4.18.8 System Log Choose menu “System Tools → System Log”, and then you can view the logs of the router. Figure 4-104 System Log Auto Mail Feature - Indicates whether auto mail feature is enabled or not. Mail Settings - Set the receiving and sending mailbox address, server address, validation information as well as the timetable for Auto Mail Feature, as shown in Figure 4-105. Figure 4-105 Mail Account Settings • From - Your mail box address.
TL-WR1043ND 300Mbps Wireless N Gigabit Router • To - Recipient’s address. The destination mailbox where the logs would be received. • SMTP Server - Your smtp server. It corresponds with the mailbox filled in the From field. You can log on the relevant website for help if you are not clear with the address. • Authentication - Most SMTP Server requires Authentication. It is required by most mailboxes that need User Name and Password to log in.
TL-WR1043ND Figure 4-106 300Mbps Wireless N Gigabit Router Statistics Current Statistics Status - Enable or Disable. The default value is disabled. To enable it, click the Enable button. If it is disabled, the function of DoS protection in Security settings will be disabled. Packets Statistics Interval （5-60） - The default value is 10. Select a value between 5 and 60 seconds in the drop-down list. The Packets Statistic interval indicates the time section of the packets statistic.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Statistics Table: IP/MAC Address Total The IP and MAC address are displayed with related statistics. Packets The total number of packets received and transmitted by the router. Bytes The total number of bytes received and transmitted by the router. Packets Bytes The total number of packets received and transmitted in the last Packets Statistic interval seconds.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Appendix A: FAQ 1. How do I configure the router to access Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the Internet port on the router. The telephone cord plugs into the Line port of the ADSL Modem. 3) Login to the router, click the “Network” menu on the left of your browser, and click "WAN" submenu.
TL-WR1043ND 1) 300Mbps Wireless N Gigabit Router Login to the router, click the “Network” menu on the left of your browser, and click "WAN" submenu. On the WAN page, select “Dynamic IP” for "WAN Connection Type", finish by clicking “Save”. 2) Some ISPs require that you register the MAC Address of your adapter, which is connected to your cable/DSL Modem during installation.
TL-WR1043ND Figure A-5 300Mbps Wireless N Gigabit Router Add or Modify a Virtual server Entry Note: Your opposite side should call your WAN IP, which is displayed on the “Status” page. 4) How to enable DMZ Host: Log in to the router, click the “Forwarding” menu on the left of your browser, and click "DMZ" submenu. On the "DMZ" page, click Enable radio button and type your IP address into the “DMZ Host IP Address” field, using 192.168.0.169 as an example, remember to click the Save button.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Figure A-7 Basic Security 4. I want to build a WEB Server on the LAN, what should I do? 1) Because the WEB Server port 80 will interfere with the WEB management port 80 on the router, you must change the WEB management port number to avoid interference. 2) To change the WEB management port number: Log in to the router, click the “Security” menu on the left of your browser, and click "Remote Management" submenu.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Note: If the above configuration takes effect, you can visit and configure the router by typing http://192.168.0.1:88 (the router’s LAN IP address: Web Management Port) in the address field of the Web browser. If the LAN IP of the modem connected with your router is 192.168.0.x, the default LAN IP of the router will automatically switch from 192.168.0.1 to 192.168.1.1 to avoid IP conflict; in this case, please try http://192.168.1.1:88.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Appendix B: Configuring the PCs In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if needed. 1. Install TCP/IP component 1) On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
TL-WR1043ND 4) 300Mbps Wireless N Gigabit Router In the prompt page that showed below, double click on the Internet Protocol (TCP/IP). Figure B-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Appendix C: Specifications General Standards IEEE 802.3, IEEE 802.3u, IEEE 802.11b, IEEE 802.11g and IEEE 802.
TL-WR1043ND 300Mbps Wireless N Gigabit Router Appendix D: Glossary 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium (EWC) [3] was formed to help accelerate the IEEE 802.
TL-WR1043ND 300Mbps Wireless N Gigabit Router SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name.
