TL-WPS510U Pocket-Sized Wireless N Print Server REV4.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired operation of the device.
NCC Notice & BSMI Notice 注意！ 依據 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、 加大功率或變更原設計之特性或功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即 停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射 頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。減少電磁波影響，請 妥適使用。 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: Pocket-Sized Wireless N Print Server Model No.
CONTENTS Package Contents ....................................................................................................1 Chapter 1. Introduction.........................................................................................2 1.1 Product Overview ...................................................................................................... 2 1.2 Features .................................................................................................................... 2 1.
4.5 4.4.1 Factory Default ......................................................................................................... 48 4.4.2 Firmware Upgrade.................................................................................................... 49 Restart..................................................................................................................... 50 Appendix A: How to Reset the Print Server .........................................................
TL-WPS510U Pocket-Sized Wireless N Print Server Package Contents One TL-WPS510U Pocket-Sized Wireless N Print Server One external AC power adapter One USB cable One Quick Installation Guide One Resource CD containing Utility and User Guide 1
TL-WPS510U Pocket-Sized Wireless N Print Server Chapter 1. Introduction 1.1 Product Overview The external print servers enhance capability by letting you place your printers at convenient locations directly on the Ethernet network, and by increasing network printer performance and management. Please note that the print server does not support printing with host-based printers, e.g. CAPT, GDI, and PPA. 1.2 Features Travel size design, small enough to take on the road Compatible with IEEE 802.
TL-WPS510U 1.4 Factory Default Settings Username: admin Password: admin Wireless Mode: Ad-Hoc (Peer-to-Peer) Channel: 1 SSID: WLAN-PS Encryption: None IP Address: 192.168.0.10 Subnet Mask: 255.255.255.
TL-WPS510U Pocket-Sized Wireless N Print Server Chapter 2. Hardware Installation 2.1 Preparation Before you start, you should prepare the following items: One USB Printer (non-GDI/CAPT) One 802.11n Access Point/Router One Computer with Wireless Adapter installed Note: Please make sure the computer has been successfully installed the printer driver, i.e., when correctly connected to the printer, the computer can print without other configurations. 2.
TL-WPS510U Pocket-Sized Wireless N Print Server 4. Power on the print server. 5. Wait 40 seconds for the print server’s Power On Self Test (POST).
TL-WPS510U Pocket-Sized Wireless N Print Server Chapter 3. How to Configure the Print Server 3.1 Using Utility in Windows XP/Vista/7/8 3.1.1 Setting up a Print Server Network To connect to the print server using PSWizard, the configurations for Windows XP, Windows Vista, Windows 7 and Windows 8 are similar. Here we take Windows 7 for example. 1. Insert the setup CD into your CD-drive. The autorun program will be started as shown in Figure 3-1. Select the model (TL-WPS510U) of your print sever.
TL-WPS510U 2. Pocket-Sized Wireless N Print Server Choose Easy Setup Wizard. Figure 3-2 3. Then a prompt will appear as shown in Figure 3-3. Make sure you have installed the printer driver, and click Continue.
TL-WPS510U 4. Pocket-Sized Wireless N Print Server Then the Wireless Print Server Setup Wizard will appear as shown in Figure 3-4. Select the wireless router to connect to the print server and click “Next”. Figure 3-4 Note: Please make sure your router’s DHCP feature is enabled. 5. If your wireless router is secured, the Input Key window will prompt. Enter and confirm the network key. Click “Connect”.
TL-WPS510U 6. Pocket-Sized Wireless N Print Server On the Select a Print Server screen as shown in Figure 3-6, select the print server and click “Next”. Figure 3-6 Note: If you can’t find the print server in the list, please check whether its power LED is on (red). If the power LED is on and the print server still doesn’t appear, please reset it. For the reset method, please refer to Appendix A: How to Reset the Print Server.
TL-WPS510U 7. Pocket-Sized Wireless N Print Server On the TCP/IP Settings page as shown in Figure 3-7, select “Obtain an IP address automatically (use DHCP)” and then click “Next”. Figure 3-7 8. Then a prompt will appear to ask whether you have installed printer driver before. Click “YES”.
TL-WPS510U 9. Pocket-Sized Wireless N Print Server Then the Select a Printer page will appear. Select the printer you’ve installed the printer driver, and click “Next”. Figure 3-9 10. Click “Finish” to complete the configuration. Now the computer can use the printer via the print server.
TL-WPS510U Pocket-Sized Wireless N Print Server 3.1.2 Joining the Print Server Network If another computer wants to join the print server network to share the printer, please follow the steps bellow. Note: Please make sure the computer has been successfully installed the printer driver, i.e., when correctly connected to the printer, the computer can print without other configurations. 1. Connect the computer to your router or access point. For details, please refer to your router’s installation guide.
TL-WPS510U 3. Choose Setup Wizard. Figure 3-12 4. The Welcome page will appear. Click “Next”.
TL-WPS510U 5. Pocket-Sized Wireless N Print Server On the Select A Print server page, select your print server and click “Next”. Figure 3-14 6. On the Change Settings page, select “No, I don’t want to change settings. (O)” and click “Next”.
TL-WPS510U 7. Pocket-Sized Wireless N Print Server On the Summery page, click “Next”. Figure 3-16 8. Click “Finish” on the Installation Complete page. Figure 3-17 Now, the computer has successfully joined the infrastructure network, and it can also use the printer via the print server.
TL-WPS510U 3.2 Pocket-Sized Wireless N Print Server Using Web Management Page in Windows XP/Vista/7/8 3.2.1 Setting up a Print Server Network To connect to the print server using the web management page, the configurations for Windows XP, Windows Vista, Windows 7 and Windows 8 are similar. Here we take Windows 7 for example. 1. On the Windows taskbar, click the Start->Control Panel. Figure 3-18 2. Click View network status and tasks.
TL-WPS510U 3. Pocket-Sized Wireless N Print Server Click Change adapter settings. Figure 3-20 4. Right click Wireless Network Connection, and select Properties.
TL-WPS510U 5. Pocket-Sized Wireless N Print Server Double click Internet Protocol Version 4 (TCP/IPv4), or select it and then click Properties. Figure 3-22 6. Select “Use the following IP address” and input a static IP address 192.168.0.X (1
TL-WPS510U Pocket-Sized Wireless N Print Server Figure 3-23 7. Left-click the icon at the right bottom on your desktop and the wireless network list wil appear. Select the SSID WLAN-PS of wireless print server and then click Connect. (Here we use Windows Zero Configuration as an example. You can also use vendor utility of wireless adapter.
TL-WPS510U 8. Pocket-Sized Wireless N Print Server Once the connection is successful, you will see the following screen shown in Figure 3-25. Figure 3-25 9. Open a web-browser and type in the IP address of the print server (the default is 192.168.0.10) in the address field of the browser to login to the web management of the print server. Figure 3-26 10. After a moment, a login window will appear, similar to the Figure 3-27.
TL-WPS510U Pocket-Sized Wireless N Print Server Figure 3-28 12. Click “Setup” and then choose “TCP/IP”. Check “Use the following TCP/IP Settings” radio button and then fill in the following parameters. IP Address: Specify an IP address for your print server. The IP address must be within the same subnet as your wireless router or access point. For example, if the LAN IP address of your wireless router or access point is 192.168.1.1, the IP address should be set to 192.168.1.X (1
TL-WPS510U Pocket-Sized Wireless N Print Server Figure 3-29 13. Click Save & Restart and then wait the print server to save the changes and restart.
TL-WPS510U Pocket-Sized Wireless N Print Server 14. Enter the “Internet Protocol (TCP/IP) Properties” page as shown in Figure 3-31. Fill in the following parameters. IP Address: Specify an IP address for your adapter. The IP address must be within the same subnet as your wireless router or access point. For example, if the LAN IP address of your wireless router or access point is 192.168.1.1, the IP address should be set to 192.168.1.X (1
TL-WPS510U Figure 3-32 24 Pocket-Sized Wireless N Print Server
TL-WPS510U Pocket-Sized Wireless N Print Server 16. Click Save & Restart button and then wait the print server to restart. Figure 3-33 17. Connect your computer to the wireless router. We take TP-LINK_A4161E for example. The password is 0123456789.
TL-WPS510U Pocket-Sized Wireless N Print Server Figure 3-35 18. Install a printer. If you’ve already installed the printer on your computer, please refer to C-1 If You Have Installed a Printer Before to add a Standard TCP/IP port for it. If you never install a printer on your computer, please refer to C-2 If You Never Install a Printer Before to install a printer and add a Standard TCP/IP port for it. 3.2.
TL-WPS510U 3.3 Pocket-Sized Wireless N Print Server Using Web Management Page in MAC OS 3.3.1 Setting up a Print Server Network 1. Click the Apple Icon on the left side of the top-bar, and then choose System Preferences…. Figure 3-36 2. On the new window, please choose Network.
TL-WPS510U 3. Pocket-Sized Wireless N Print Server Follow the steps as shown in Figure 3-38 and Figure 3-39 to set the IP address.
TL-WPS510U 4. Pocket-Sized Wireless N Print Server Connect your MAC computer to the TL-WPS510U. In default, the print server will work on Ad-Hoc mode with the SSID WLAN-PS, so please select the wireless network WLAN-PS to connect. If you need to reset the TL-WPS510U but don’t know how to do, please refer to the Appendix A: How to Reset the Print Server.
TL-WPS510U 5. Pocket-Sized Wireless N Print Server Open the Safari and login to the TL-WPS510U (default Name: admin, default Password: admin). Go to “Setup -> TCP/IP”, and then select “Use the following TCP/IP settings”. Change its IP Address and Subnet Mask to 192.168.1.10 and 255.255.255.0; enter your router’s IP address in the Default Router blank (e.g. 192.168.1.1). After the configuration, click Save & Restart.
TL-WPS510U 6. Pocket-Sized Wireless N Print Server Change the MAC computer’s IP Address, Subnet Mask to 192.168.1.101 and 255.255.255.0; enter your router’s IP address in the Router blank (e.g. 192.168.1.1). Click “OK” and the MAC computer will be automatically connected to the network WLAN-PS again. Figure 3-43 7. Login to the TL-WPS510U and go to “Setup -> Wireless”. Configure the wireless parameters according to your wireless router. After the configuration, click Save & Restart.
TL-WPS510U Figure 3-44 Figure 3-45 32 Pocket-Sized Wireless N Print Server
TL-WPS510U 8. Pocket-Sized Wireless N Print Server Connect your MAC computer to the wireless router. We take TP-LINK_61BB7A for example. The password is 0123456789.
TL-WPS510U 9. Pocket-Sized Wireless N Print Server Try to access the TL-WPS510U and you can see Wireless status. The TL-WPS510U is working on Infrastructure mode and can communicate with the wireless router and your MAC computer.
TL-WPS510U Pocket-Sized Wireless N Print Server 3.3.2 Printer Installation in MAC OS 1. Click the Apple icon -> System Performances -> Print & Scan to add a Standard TCP/IP port for the printer.
TL-WPS510U 2. Click Pocket-Sized Wireless N Print Server . Figure 3-50 3. Select “IP”, and then configure the following parameters as shown in Figure 3-51 and Figure 3-52. Select “Line Printer Daemon - LPD” for Protocol and enter the print server’s IP 192.168.1.10 for Address and lp1 for Queue. Give a name to your printer. For Print Using, go to “Select Printer Software…” and select your printer model from the list. Here takes HP Deskjet 1000 J110 series for example. And then click Add.
TL-WPS510U Pocket-Sized Wireless N Print Server 1 2 7 3 4 5 8 6 Figure 3-51 9 Figure 3-52 37
TL-WPS510U 4. Pocket-Sized Wireless N Print Server Till now you've successfully installed the print server and can print via the TL-WPS510U. Figure 3-53 3.3.3 Joining the Print Server Network If another computer wants to join the print server network to share the printer, please follow the steps bellow. 1. Connect the computer to your router or access point. For details, please refer to your router’s installation guide. 2. Install a printer. For details, please refer to 3.3.
TL-WPS510U Pocket-Sized Wireless N Print Server Chapter 4. More Configuration for the Print Server The Print Server contains an embedded web server that can be accessed through a supported web browser on a WLAN, for example, IE6, Firefox or above is recommended. The embedded web server provides access to configuration and management pages for the print server and the connected peripheral device. To use the embedded web server, you should first connect your adapter to the print server. 4.
TL-WPS510U Figure 4-3 40 Pocket-Sized Wireless N Print Server
TL-WPS510U 4.2 Pocket-Sized Wireless N Print Server Status The Status page shows the current information about the print server as shown in Figure 4-3. By clicking the corresponding tab, you can view the following information, including System, Printer, Wireless, and TCP/IP. 4.2.1 System Figure 4-4 Print Server Name: This option allows you to view device name of the print server. To correct the print server’s device name.
TL-WPS510U Pocket-Sized Wireless N Print Server 4.2.2 Printer Figure 4-5 Manufacturer: This option allows you to view manufacturer of the printer. When the printer connected with the print server, it will be show in the manufacture box. Model Number: This option allows you to view model of the printer. When the printer connected with the print server, it will be show in the model box. Printing Language Supported: This option allows you to view command to set the printer.
TL-WPS510U Pocket-Sized Wireless N Print Server 4.2.3 Wireless The Wireless Status page shows the current wireless information of the print server. Figure 4-6 4.2.4 TCP/IP The TCP/IP Status page shows the current TCP/IP settings of the print server.
TL-WPS510U Pocket-Sized Wireless N Print Server Use DHCP/BOOTP: This option allows you to view DHCP/ BOOTP status. If there is a DHCP/BOOTP server on your network, this option allows the print server to obtain IP-related settings automatically from your DHCP server. IP Address: This option allows you to view IP address from the print server. The IP address must meet the IP addressing requirements of the network segment. (default: 192.168.0.
TL-WPS510U Pocket-Sized Wireless N Print Server E-mail Alert: This option allows you to receive alert of the device. SMTP Server IP Address: Enter the IP Address of the SMTP Server. Administrator E-mail Address: Enter the e-mail address used to receive alert. Print Server Name: This option allows you to input device name of the print server. To correct the print server’s device name. Password: This option allows you to change password of the print server. Factory default is admin.
TL-WPS510U 4.3.2 Wireless Setup Click Wireless, the following screen will appear.
TL-WPS510U Pocket-Sized Wireless N Print Server Basic Settings: Network Type: To change the WLAN type to Ad-Hoc (default) or Infrastructure. SSID: To change the SSID to connect an existing wireless network.(default: WLAN-PS) Channel: Indicates the channel setting for this print server. Transmission Rate: Select the basic transfer rates based on the speed of wireless network.
TL-WPS510U Pocket-Sized Wireless N Print Server IP Address: This option allows you to input IP address from the print server. The IP address must meet the IP addressing requirements of the network segment. Note: On the TCP/IP Setup screen, specify a fixed IP address is highly recommended. Subnet Mask: This option allows you to input subnet mask from the print server. The IP address must meet the IP addressing requirements of the network segment.
TL-WPS510U Pocket-Sized Wireless N Print Server 4.4.2 Firmware Upgrade Click Browse… to select the firmware file and then click Firmware Upgrade to upgrade the firmware of the print server.
TL-WPS510U 4.5 Restart Click OK to reboot the print server.
TL-WPS510U Pocket-Sized Wireless N Print Server Appendix A: How to Reset the Print Server If you lose the connection with TL-WPS510U because of wrong configuration, you need to reset it to factory default settings and configure it again. Follow the steps below to reset TL-WPS510U: 1. Unplug the power adapter of TL-WPS510U; 2. Press and hold the Reset button on TL-WPS510U; 3. Plug in the power adapter of TL-WPS510U and continue pressing the Reset button for about 10 seconds. 4.
TL-WPS510U Pocket-Sized Wireless N Print Server Appendix B: Frequently Asked Questions 1. 2. Print jobs are sent to the print queue successfully, but fail to be sent to the printer. 1) Check all the information of the print server by running PSAdmin. 2) Check to see that if the power adapters are properly connected. 3) Recheck the print server connection by running the PSAdmin. 4) Check all the information in print port setting.
TL-WPS510U 7. Pocket-Sized Wireless N Print Server TCP/IP Problems A. The print server's Node ID you specified in the "arp" command is not correct. If this is the case, please ensure the Node ID field in the corresponding entry of the print server's IP address in NT's ARP cache table is correct by typing the following command at NT's DOS prompt. "arp -a" If the Node ID shown on the screen doesn't match the print server's Node ID, please follow the instructions below to reset the entry.
TL-WPS510U Pocket-Sized Wireless N Print Server Appendix C: Printer Installation in Windows OS Other computers in the same local network that need to share the printing should add the Standard TCP/IP port on their system. There’re two conditions. Please choose one according to your system. C-1 is on the precondition that you have ever installed a printer driver and now you want to use a print server to share the printer through your network. You need to change the printer port to Standard TCP/IP port.
TL-WPS510U 2. Pocket-Sized Wireless N Print Server Find your installed printer icon, right-click on it, and select Properties. Figure C-2 3. Click Ports > Add Port > Standard TCP/IP Port > New Port > Next.
TL-WPS510U 4. Pocket-Sized Wireless N Print Server Input the exact IP address of print server. Click Next. (You can login to the print server, and go to Status -> TCP/IP to find the IP address of print server. Here we take 192.168.1.10 for example.) Figure C-4 5. Select Custom, and click Settings.
TL-WPS510U 6. Choose LPR, and input the queue name as lp1. Click OK. Figure C-6 7. Pocket-Sized Wireless N Print Server Click Next and then Finish, to complete the wizard.
TL-WPS510U Figure C-8 8. Click Close and Apply.
TL-WPS510U Pocket-Sized Wireless N Print Server Figure C-10 9. Now, the printer port has been created. C-2 If You Never Install a Printer Before 1. Click Star > Control Panel, and select Devices and Printers.
TL-WPS510U 2. Click Add a printer. Figure C-12 3. Select Add a local printer.
TL-WPS510U 4. Pocket-Sized Wireless N Print Server Select “Create a new port”, and the type of port is “Standard TCP/IP Port”. Figure C-14 5. Input the IP address of the print server and click Next. (You can login to the print server, and go to Status -> TCP/IP to find the IP address of print server. Here we take 192.168.1.10 for example.) The windows will detect the TCP/IP Port. Please wait for the next page.
TL-WPS510U Pocket-Sized Wireless N Print Server Figure C-16 6. On the following page, select Custom and click Settings. And then on the next page, please select LPR as the Protocol and the Queue Name is lp1.
TL-WPS510U 7. Pocket-Sized Wireless N Print Server The windows will ask you to install the driver of the printer. You can select one in the list or click Have Disk to install other drivers. Please follow the steps to finish the installation.
TL-WPS510U Pocket-Sized Wireless N Print Server Figure C-20 8. After that, the new printer is in the list. And you can enjoy the sharing.
TL-WPS510U Pocket-Sized Wireless N Print Server Appendix D: Additional Installation Instructions Panasonic KX-P6100/6300/6500 If you are using a Panasonic KX-P6100/6300/6500 laser printer with the print server through the Network Print Port under Windows 95/98, please redirect the printer named “Panasonic KX-P6100 PCL” or “Panasonic KX-P6300 PCL”, or “Panasonic KX-P6500 PCL” to the print server through the Network Print Port.
