Easy Smart Configuration Utility User Guide Easy Smart Configuration Utility REV1.0.
Easy Smart Configuration Utility User Guide CONTENTS Chapter 1 About this Guide.................................................................................3 1.1 Intended Readers ...................................................................................................... 3 1.2 Conventions............................................................................................................... 3 1.3 Overview of This Guide ............................................................
Easy Smart Configuration Utility User Guide 6.2 Port Based VLAN .................................................................................................... 35 6.3 802.1Q VLAN .......................................................................................................... 37 6.4 802.1Q PVID Setting ............................................................................................... 38 Chapter 7 QoS .........................................................................
Easy Smart Configuration Utility User Guide Chapter 1 About this Guide This User Guide contains information for setup and guidance of the Easy Smart Configuration Utility. Please read this guide carefully before operation. 1.1 Intended Readers This Guide is intended for network managers familiar with IT concepts and network terminologies. 1.2 Conventions In this Guide the following conventions are used: Menu Name→Submenu Name indicates the menu structure.
Easy Smart Configuration Utility User Guide Chapter Introduction Chapter 3 System This module is used to configure system properties of the switch. Here mainly introduces: Chapter 4 Switching Chapter 5 Monitoring System Info: View device information and define the device description. IP Setting: Get and modify the network parameters of the switch. User Account: Modify the username and password for users to log on to the Web management page.
Easy Smart Configuration Utility User Guide Chapter Introduction Chapter 6 VLAN This module is used to configure VLANs to control broadcast in LANs. Here mainly introduces: Chapter 7 QoS This module is used to configure QoS function to provide different quality of service for various network applications and requirements. Here mainly introduces: Chapter 8 Help MTU VLAN: Set the MTU VLAN mode. Port Based VLAN: Set the Port-Based VLAN mode 802.1Q VLAN: Set the 802.1Q Tag VLAN mode. 802.
Easy Smart Configuration Utility User Guide Chapter 2 2.1 Getting Started Introduction Easy Smart Configuration Utility is the management software for the TP-LINK Easy Smart Switches. The utility allows operators to centrally manage entire networks of the Easy Smart Switches, such as TL-SG1016DE/TL-SG1024DE. We will take TL-SG1024DE for example throughout this Guide. 2.
Easy Smart Configuration Utility User Guide 2. Then the following screen will appear. Click Next to continue. If you want to stop the installation, click Cancel. Figure 2-2 Welcome to the InstallShield Wizard 3. Choose the destination location for the installation files and click Next to continue. Figure 2-3 Choose Destination Location By default, the installation files are saved on the Program Files folder of system disk. Click the Change button to modify the destination location proper to your need.
Easy Smart Configuration Utility User Guide Figure 2-4 Install the Utility 5. The InstallShield Wizard is installing Easy Smart Configuration Utility shown as the following screen. Please wait. Figure 2-5 Setup Status 6. On the following screen, click Finish to complete the installation.
Easy Smart Configuration Utility User Guide Figure 2-6 InstallShield Wizard Complete 7. The installation process creates a TP-LINK subdirectory under the \Program Files directory on your computer, copies the utility program into the \Program Files\TP-LINK\Easy Smart Configuration Utility directory, and places a utility icon 2.3 on the computer desktop.
Easy Smart Configuration Utility User Guide Figure 2-8 Login 4. After a successful login, the main page will appear. Figure 2-9 Main Page 5. Click System→System Tools→Firmware Upgrade to load the following page.
Easy Smart Configuration Utility User Guide Figure 2-10 Firmware Upgrade 6. Click Ready and click OK in the pop-up window to restart the switch. Figure 2-11 Reboot Device 7. After the switch restarts, click the Browse button to choose the latest firmware for the switch in your computer and click Upgrade to start the upgrade process. The switch will restart after the upgrade.
Easy Smart Configuration Utility User Guide Figure 2-12 Choose the File to Upgrade 8. The following steps to upgrade the loader are optional. If you upgrade the loader here, the switch’s configurations will remain the same after the next firmware upgrade. After the switch restarts successfully, type the address http://192.168.0.1/Loader UpgradeRpm.htm in the address field of the browser to access the loader upgrade interface of the switch. Figure 2-13 Loader Upgrade 9.
Easy Smart Configuration Utility User Guide Figure 2-15 Device Restart 2.4 Switch Discovery When the utility is launched, it immediately searches the network for TP-LINK Easy Smart Switches. The discovered switches are listed as below. Figure 2-16 Main Page Click Help in the left bottom to access to the TP-LINK support website for more help. Note: The maximum number of the discovered switches is 30. 2.5 Switch Settings You can select a switch and click to configure or display its status.
Easy Smart Configuration Utility User Guide Figure 2-17 Discovered Switch The setting figure will shown as below: Figure 2-18 Switch Setting You can configure the switch’s Device Description, DHCP Setting, IP Address, Subnet Mask and Default Gateway on this page. The login User Name and Password are required to complete the configuration. By default, they are both admin. Clicking Apply can only make the new configurations effective before the switch is rebooted.
Easy Smart Configuration Utility User Guide 2.7 Utility Features Overview You can select a switch and click or double click its corresponding entry to log on to the switch for further configuration. Figure 2-20 Discovered Switch Enter the User Name and Password to log on to the configuration interface. They are both admin by default.
Easy Smart Configuration Utility User Guide Figure 2-22 Switch Configuration Area in the red box shows the device model number of the switch that you are managing now. Click the icon to save the current configurations. Click the icon to return to the discovering page. Note: The switch you log on to should be in the same subnet with your computer. 2.8 Uninstall the Utility If you want to remove the Easy Smart Configuration Utility, please take the following steps: 1.
Easy Smart Configuration Utility User Guide Figure 2-23 Preparing Setup 2. Then the following screen will appear. If you want to stop the remove process, click Cancel.
Easy Smart Configuration Utility User Guide 3. On the continued screen, click Yes to remove the utility from your PC. Figure 2-25 Uninstall the Utility 4. Click Finish to complete.
Easy Smart Configuration Utility User Guide Chapter 3 System The System module is mainly for system configuration of the switch, including seven submenus: System Info, IP Setting, User Account, Backup and Restore, System Reboot, System Reset and Firmware Upgrade. 3.1 System Info On this page you can view the system information and define the device description. Choose the menu System→System Info to load the following page.
Easy Smart Configuration Utility User Guide Device Description: 3.2 Give a description to the device for identification. IP Setting Each device in the network possesses a unique IP address. You can log on to the IP Setting page to operate the switch using this IP address. The switch supports the DCHP mode to obtain an IP address. The IP address obtained using a new mode will replace the original IP address. On this page you can get and modify the network parameters of the switch.
Easy Smart Configuration Utility User Guide Choose the menu System→User Account to load the following page. Figure 3-3 System User Setting The following entries are displayed on this screen: System User Setting User Name: Create a name for administrator’s login. Old Password: Type the old password. Password: Type a new password for administrator’s login. Confirm Password: Retype the new password. Note: 1.
Easy Smart Configuration Utility User Guide The following entries are displayed on this screen: System Config Backup Backup Config: Click the Backup Config button to save the current configuration as a file to your computer. You are suggested to take this measure before upgrading. System Config Restore Restore Config: Click the Choose File button to select the backup configuration file, then click the Restore Config button. It will take effect after the switch automatically reboots. Note: 1.
Easy Smart Configuration Utility User Guide Choose the menu System→System Reset to load the following page. Figure 3-6 System Reset Note: After the system is reset, the switch will be reset to the default and all the settings will be cleared. 3.7 Firmware Upgrade The switch system can be upgraded via this management page. To upgrade the system is to get more functions and better performance. Go to http://www.tp-link.com to download the updated firmware.
Easy Smart Configuration Utility User Guide Chapter 4 Switching Switching module is used to configure the basic functions of the switch, including three submenus: Port Setting, IGMP Snooping and Port Trunk. 4.1 Port Setting On this page, you can configure the basic parameters for the ports. When the port is disabled, the packets on the port will be discarded. Disabling the port which is vacant for a long time can reduce the power consumption effectively. And you can enable the port when it is in need.
Easy Smart Configuration Utility User Guide Speed and Duplex: Config: Select the Speed and Duplex mode for the port. The device connected to the switch should be in the same Speed and Duplex mode with the switch. When “Auto” is selected, the Speed and Duplex mode will be determined by auto-negotiation. Actual: Displays the actual working state of the port. Flow Control: Config: Select On/Off to Enable/Disable the Flow Control feature.
Easy Smart Configuration Utility User Guide Figure 4-2 IGMP Snooping The following entries are displayed on this screen: IGMP Snooping IGMP Snooping: 4.3 Enable or disable IGMP snooping function globally on the switch. Multicast IP Table IP Address: Displays the multicast IP address. VLAN ID: Displays the VLAN ID of the multicast group. If the packet does not carry VLAN ID, then here displays the PVID of the port.
Easy Smart Configuration Utility User Guide On this page, you can configure and view the information of the trunk group of the switch. Choose the menu Switching→Port Trunk to load the following page. Figure 4-3 Trunk Config Here you can configure and view the port parameters. Trunk Config Trunk ID: Select an identified number for the trunk group from the drop-down list. Port: Select the port as the trunk group member. It is multi-optional.
Easy Smart Configuration Utility User Guide Delete: Delete the selected Trunk. Tips: 1. The Trunk can be deleted by clearing its all member ports. 2. A port can only be added to a Trunk.
Easy Smart Configuration Utility User Guide Chapter 5 Monitoring Monitoring module monitors the traffic information of the switch, and provides the convenient method to locate and solve the network problem, includes four submenus: Port Statistics, Port Mirror, Cable Test and Loop Prevention. 5.1 Port Statistics On this page you can view the statistic information of each port, which facilitates you to monitor the traffic and locate faults promptly.
Easy Smart Configuration Utility User Guide 5.2 TxBadPkt: Displays the number of error packets transmitted on the port. RxGoodPkt: Displays the number of good packets received on the port. The error packets are not counted in. RxBadPkt: Displays the number of error packets received on the port. Port Mirror Port mirror functions to monitor and mirror network traffic by forwarding copies of incoming and outgoing packets from one/multiple ports (mirrored port) to a specific port (mirroring port).
Easy Smart Configuration Utility User Guide Ingress: Select whether to monitor the ingress traffic. When the ingress is enabled, the ingress traffic received by the mirrored port will be copied to the mirroring port. Egress: Select whether to monitor the egress traffic. When the egress is enabled, the outgoing packets sent by the mirrored port will be copied to the mirroring port. Note: 1. The trunk member cannot be selected as the mirroring port. 2.
Easy Smart Configuration Utility User Guide Test Result: Displays the connection status of the cable connected to the port. The test results of the cable include “No Cable”, “Open”, “Short”, ”Open Short”, “Normal”, “Cro Cable” and “others”. Cable Fault Distance(m): Displays the error length (in meters) of the cable. Test: Click Test to diagnose the cable connected to this port. Test ALL: Click Test All to carry on the cable test on all ports. Note: The test result is just for your reference. 5.
Easy Smart Configuration Utility User Guide Chapter 6 VLAN The traditional Ethernet is a data network communication technology based on CSMA/CD (Carrier Sense Multiple Access/Collision Detect) via shared communication medium. Through the traditional Ethernet, the overfull hosts in LAN will result in serious collision, flooding broadcasts, poor performance or even breakdown of the Internet.
Easy Smart Configuration Utility User Guide specific hosts. When the physical position of a host changes within the range of the VLAN, you do not need to change its network configuration. There are 3 types of VLAN modes supported in the switch: 1. MTU VLAN MTU VLAN (Multi-Tenant Unit VLAN) defines an uplink port which will build up several VLANs with each of the other ports.
Easy Smart Configuration Utility User Guide packet refers to the packet without VLAN tag. The VLAN module is mainly for VLAN configuration, including four submenus: MTU VLAN, Port Based VLAN, 802.1Q VLAN and 802.1Q PVID Setting. 6.1 MTU VLAN On this page you can choose to enable MTU VLAN mode and configure VLANs. Choose the menu VLAN→MTU VLAN to load the following page. Figure 6-3 MTU VLAN Configuration The following entries are displayed on this screen: 6.
Easy Smart Configuration Utility User Guide Figure 6-4 Port Based VLAN Configuration To ensure the normal communication of the factory switch, the default VLAN of all ports is set to VLAN1. VLAN 1 cannot be deleted. The following entries are displayed on this screen: Global Config Port Based VLAN Configuration: Enable or disable Port Based VLAN mode. Port Based VLAN Setting VLAN ID: Ports: Select the ID number of VLAN from the pull-down list. Click the port icon to select the port of the VLAN.
Easy Smart Configuration Utility User Guide 6.3 802.1Q VLAN On this page you can configure 802.1Q VLAN feature and view the related settings. Choose the menu VLAN→802.1Q VLAN to load the following page. Figure 6-5 802.1Q VLAN Configuration To ensure the normal communication of the factory switch, the default VLAN of all ports is set to be VLAN1. VLAN 1 cannot be modified or deleted. The following entries are displayed on this screen: Global Config 802.1Q VLAN Status： Enable or disable 802.
Easy Smart Configuration Utility User Guide Untagged Ports： Click the port icon to configure the egress rule of the traffic on this port as untagged. The switch drops the tag header before sending the packet. Tagged Ports： Click the port icon to configure the egress rule of the traffic on this port as tagged. The switch adds the tag header before sending the packet. 6.4 VLAN ID： Displays the ID number of VLAN. VLAN Name： Displays the user-defined name of VLAN.
Easy Smart Configuration Utility User Guide Figure 6-6 802.1Q VLAN PVID Setting The following entries are displayed on this screen: 802.1Q VLAN PVID Setting Select: Select the desired port for configuration. It is multi-optional. Port: Displays the port number. PVID: Enter a PVID number for the port. When adding the tag header to the received untagged packet, the switch will automatically uses this PVID value as the VLAN ID of the added tag. Note: 802.1Q VLAN should be enabled before setting PVID.
Easy Smart Configuration Utility User Guide Chapter 7 QoS QoS (Quality of Service) functions to provide different quality of service for various network applications and requirements and optimize the bandwidth resource distribution so as to provide a network service experience of a better quality. QoS This switch classifies the ingress packets, maps the packets to four different priority queues and then forwards the packets according to Strict-Priority scheduling algorithms to implement QoS function.
Easy Smart Configuration Utility User Guide 1. Port Based When port-base QoS mode is enabled, the user can manually map the ingress packets of the port to four different priority queues. After that, the switch will preferentially send packets in the queue with higher priority, and only when the queue with higher priority is empty, packets in the queue with lower priority are sent. 2. 802.1P Based Figure 7-2 802.1Q Frame As shown in the figure above, each 802.1Q Tag has a Pri field, comprising 3 bits.
Easy Smart Configuration Utility User Guide 7.1 QoS Basic This switch classifies the ingress packets, maps the packets to different priority queues and then forwards the packets to implement QoS function. This switch implements two priority modes based on port and on 802.1P. The port-based QoS mode supports four priority queues. The port priority queues are labeled as 1, 2, 3, and 4. On this page you can configure and view QoS mode and the port-based priority setting.
Easy Smart Configuration Utility User Guide and maps the packets to different priority queues based on the 802.1p priority field in the 802.1Q tag. 7.2 Port Based Priority Setting Select: Select the desired port for configuration. It is multi-optional. Port: Displays the port number. Priority Queue: Specify the priority queue the packets from the port are mapped to. The priorities are labeled as 1~4 and among them the bigger the value, the higher the priority.
Easy Smart Configuration Utility User Guide Figure 7-5 Bandwidth Control Setting The following entries are displayed on this screen: Bandwidth Control Select: Select the desired port for Rate configuration. It is multi-optional. Port: Displays the port number of the switch. Ingress Rate (bps): Configure the bandwidth for receiving packets on the port.
Easy Smart Configuration Utility User Guide LAG: Displays the LAG number which the port belongs to. Note: 1. If you enable ingress bandwidth control feature for the storm control-enabled port, storm control feature will be disabled for this port. 2. When egress bandwidth control feature is enabled for one or more ports, you are suggested to disable the flow control on each port to ensure the switch works normally. 7.
Easy Smart Configuration Utility User Guide Select: Select the desired port for Storm Control configuration. It is multi-optional. Port: Displays the port number of the switch. Bc Limit: Enable/Disable broadcast control feature for the port. Mc Limit: Enable/Disable multicast control feature for the port. UL Limit: Enable/Disable UL-Frame control feature for the port. Rate (Kbps): Select the bandwidth for receiving the specified packet on the port.
Easy Smart Configuration Utility User Guide Chapter 8 Help This page contains two submenus: Help and About. 8.1 Help Choose the menu Help→Help to load the following page. Figure 8-1 Help Click Online Help to access to the TP-LINK support website and to the online user guide for the Easy Smart Configuration Utility (the latest copy of this manual). 8.2 About To view the utility software version, choose the menu Help→About.
