User Guide TL-SG1008P 8-Port Gigabit Desktop Switch with 4-Port PoE Rev˖1.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNO- LOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CE Mark Warning This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. SAFETY NOTICES Cautions Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm.
CONTENT Package Contents ...................................................... 1 Chapter 1. Introduction of the Product 1.1 1.2 1.3 .......................... 2 Overview of the Product ...................................... 2 Convention ............................................................ 3 Features................................................................. 3 Chapter 2. Installation................................................. 4 2.1 2.2 Mounting the Switch on a Desk...................
Package Contents The following items should be found in your box: ¾ One TL-SG1008P 8-Port Gigabit Desktop Switch with 4-Port PoE ¾ One DC Power Adapter ¾ Four rubber cushions to be used under the Switch ¾ This User Guide Note Make sure that the box contains the above items. If any of the listed items are damaged or missing, please contact your distributor.
Chapter 1. Introduction of the Product Thank you for choosing the TL-SG1008P 8-Port Gigabit Desktop Switch with 4-Port PoE. 1.1 Overview of the Product The TL-SG1008P 8-Port Gigabit Desktop Switch with 4-Port PoE provides the seamless network connection, which integrates 1000Mbps Gigabit Ethernet, 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities. This PoE Switch is also a Power Sourcing Equipment (PSE*).
1.2 Convention The Switch or TL-SG1008P mentioned in this User Guide stands for TL-SG1008P 8-Port Gigabit Desktop Switch with 4-Port PoE without any explanation. 1.3 Features ¾ Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3x, IEEE802.3af standards ¾ 8 10/100/1000Mbps Auto-Negotiation RJ45 ports with 4 ports supporting PoE function (ports1~4), all of them support Auto-MDI/MDIX ¾ Supports PoE power up to 15.4W for each PoE port ¾ Supports PoE power up to 53W for PoE ports ¾ Supports PoE IEEE802.
Chapter 2. Installation During the installation procedure, please only use the accessories equipped with the Switch. 2.1 Mounting the Switch on a Desk To install the Switch, please follow the steps: 1) Place the Switch on a flat desk. 2) Remove the adhesive backing papers from the rubber cushions. 3) Turn over the Switch and attach the supplied four rubber cushions to the recessed areas on the bottom at each corner of the Switch. Note 1) Please avoid any heavy thing placed on the Switch.
2) Then, the 1000Mbps and Link/Act LED indicators will flash momentarily for one second, which represents a resetting of the system. Note If the LED indicators don’t respond as described above, please check the power supply and its connection. Chapter 3. Identifying External Components This Chapter describes the front panel, rear panel and LED indicators of the Switch. 3.1 Front Panel Figure 3-1 TL-SG1008P Switch Front Panel The Switch’s LEDs are located on the front panel.
Name Status Indication On (green) There is a PoE PD connected to the port, which supply power successfully. PoE ports Flashing The PoE power circuit may be in short or the (ports1~4) (green) power current may be overloaded. PoE MAX Off No PD is connected to the corresponding port, or no power is supplied according to the power limits of the port. On (red) The power of all the connected PoE ports is >=46W. No power may be supplied if additional PDs are connected.
Note If all PoE PDs power consumption is >= 53W, a priority* will be arranged among the PoE ports like port-1 = port-2 = port-3 > port-4, then the system will cut off the power of the lowest-priority port. *Priority: This function will help protect the system when the system power is overloaded. For example, Port 1, 2 and 4 is using 15.4W (maximum power for per port is 15.4W); the system power is 46.2W in total.
¾ PoE Ports (1-4): These ports support PoE function which integrates power and data onto one Ethernet cable. Once the device you connect to the Switch is identified, the Switch will supply power through the PoE port, and then you can use it as a 10/100/1000Mbps Auto-Negotiation RJ45 Ethernet port. The working status can be indicated by the corresponding LEDs on the front panel.
Appendix A: Specifications General Standard IEEE802.3, IEEE802.3u, IEEE802.3ab IEEE802.3x, IEEE802.
MAC Address Learning Automatically learning, automatically aging 10Base-T: 14880pps/Port Frame Filter Rate 100Base-Tx: 148800pps/Port 1000Base-T: 1488000pps/Port 10Base-T: 14880pps/Port Frame Forward Rate 100Base-Tx: 148800pps/Port 1000Base-T: 1488000pps/Port Environmental and Physical Power Consumption 5.8 Watts (max. no PD connected) 58.8 Watts (max.
