TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router REV: 4.0.
COPYRIGHT & TRADEMARKS is a registered trademark of Specifications are subject to change without notice. TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
This device has been designed to operate with the antennas listed below, and having a maximum gain of 5 dBi. Antennas not included in this list or having a gain greater than 5 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.
Safety Information When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. Avoid water and wet locations.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 300Mbps Wireless N USB ADSL2+ Modem Router Model No.
CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Product Overview ................................................................................... 2 1.1 Overview of the Modem Router ...................................................................................... 2 1.2 Main Features ................................................................................................................ 3 1.
4.5.12 DNS .................................................................................................................................... 52 4.5.13 DSL .................................................................................................................................... 54 4.5.14 UPnP .................................................................................................................................. 55 4.5.15 Interface Grouping ..............................................
4.12Logout ........................................................................................................................ 101 Appendix A: Specifications ................................................................................. 103 Appendix B: Troubleshooting ............................................................................. 104 Appendix C: Technical Support ..........................................................................
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Package Contents The following contents should be found in your package: One TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router One power Adapter for TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router Quick Installation Guide One RJ45 cable Two RJ11 cables One ADSL splitter One Resource CD for TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router, including: • This User Guide • Other Helpful Information Note: Ma
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Chapter 1. Product Overview Thank you for choosing the TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router. 1.1 Overview of the Modem Router The TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router integrates 4-port Switch, Firewall, NAT-router and Wireless AP.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 1.2 Main Features One RJ11 LINE port, four 10/100M Auto-Negotiation RJ45 LAN ports, supporting Auto MDI/MDIX Complies with IEEE 802.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 1.3 Panel Layout 1.3.1 The Front Panel The modem router’s LEDs are located on the front panel (View from left to right). Figure 1-1 LED Explanation: Name (Power) (ADSL) (Internet) (WLAN) (WPS) (USB) Status Indication On The modem router is powered on. Off The modem router is off. Please ensure that the power adapter is connected correctly. On ADSL line is synchronized and ready to use. Flash The ADSL negotiation is in progress.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Flash (LAN1-4) The modem router is sending or receiving data over this USB port. Off No storage device or printer is plugged into the USB port. On There is a device connected to this LAN port. Flash Off The modem router is sending or receiving data over this LAN port. There is no device connected to this LAN port. Note: 1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide RESET: There are two ways to reset the modem router's factory defaults. 1) Use the Restore Default function on Management -> settings -> Restore Default page in the modem router's Web-based Utility. 2) Use the Factory Default RESET button: With the modem router powered on, use a pin to press and hold the RESET button for at least 5 seconds. And the modem router will reboot to its factory default settings.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Chapter 2. Connecting the Modem Router 2.1 System Requirements Broadband Internet Access Service (DSL/Cable/Ethernet). PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors. TCP/IP protocol on each PC. Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. 2.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 2.3 Connecting the Modem Router Before installing the device, please make sure your broadband service provided by your ISP is available. If there is any problem, please contact your ISP. Before cable connection, cut off the power supply and keep your hands dry. You can follow the steps below to install it. Step 1: Connect the ADSL Line.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default IP address of the TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router is 192.168.1.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide You can check it following the steps below: 1) Is the connection between your PC and the modem router correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the modem router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254. 3.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 3-5 Step 3. Click Next to continue. Figure 3-6 Step 4. Choose the Operation Mode for Internet access, and then click Next. For ADSL Modem Router Mode and Wireless Router Mode, 3G Router Mode can be set as a backup internet access method. If you do not want to configure 3G settings now, just untick the option.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 3G Router Mode: In this mode, the device allows multi-users to share a 3G mobile broadband connection via wired or wireless connection. Note: If you are unwilling to configure WAN Service now, you can click the Skip WAN button. Then you can configure WAN service referring to 4.4.1 Layer2 Interface. Step 5. Configure parameters for WAN connection.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 3-9 If 3G Router Mode is chosen, you should first insert your 3G USB modem on the USB port of the modem router. Then select your location and mobile ISP. Click Save to continue. Figure 3-10 Step 6. The WLAN function is enabled by default. You can rename your wireless network name and create your own password in this page.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 3-11 Step 7. You will see the Summary screen, click Confirm to make your settings take effect.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Chapter 4. Configuring the Modem Router This chapter will show each Web page's key function and the configuration way. 4.1 Login After your successful login, you will see the eight main menus on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions. The detailed explanations for each Web page’s key function are listed below. 4.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-1 Note: Click the other submenus under the main menu Device Info, and you will be able to view the corresponding information about WAN, Statistics, Route, ARP and DHCP. 4.3 Quick Setup Please refer to Section 3.2 Quick Installation Guide. 4.4 Operation Mode Choose “Operation Mode”, and you will see the screen as shown in Figure 4-2.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide ADSL Modem Router Mode: In this mode, the device enables multi-users to share Internet via ADSL using its ADSL port and share it wirelessly at 300Mbps wireless 802.11n speeds. Wireless Router Mode: In this mode, the device enables multi-users to share Internet via Ethernet WAN (EWAN) using its interchangeable LAN/WAN port and share it wirelessly at 300Mbps wireless 802.11n speeds.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Note: To completely configure the WAN Interface, you need to first select the Layer2 Interface (4.5.1 Layer2 Interface) according to the connection ISP provides for you, and then to select the type of the connection (4.5.2 WAN Service) for the further configuration. 4.5.1 Layer2 Interface 4.5.1.1 ATM Interface Choose “Advanced Setup”“Layer2 Interface““ATM Interface”, you can Configure ATM interfaces on the screen below.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide DSL Link Type: Select a DSL Link Type which is provided by your ISP. The options include EoA (it is for PPPoE, IPoE, and Bridge), PPPoA (PPP over ATM) and IPoA (IP over ATM). Encapsulation Mode: The mode of the data processing over the Link Type you have selected. Uses the default setting, if you are not sure. Service Category: Select the type of the service assigned by your ISP in the drop-down list.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-7 Note: The following section adopts different VPI, VCI to introduce further configuration for the different connection types, if you need to change the configuration of ATM PVC (VPI/VCI), you should go to the previous section (4.5.1 Layer2 Interface) to configure them again. 4.5.2.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-9 4. Enter the following parameters and then click Next. Figure 4-10 PPP Username/Password: Enter the User Name and Password provided by your ISP. These fields are case-sensitive. PPPoE Service Name: Enter the Service Name if it was provided by your ISP. If you leave it blank, the default name will be the same as the Service Description on the previous screen.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Authentication Method: Select the Authentication Method from the drop-down list, the default method is AUTO, and you can leave it as a default setting. Note: If you are not sure about the PPP IP extension and PPP Debug Mode etc. below, please don’t select these options. MTU Size: Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1480 Bytes.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 6. Configure the DNS Server Addresses on the screen below and click Next. Figure 4-12 Select DNS Server Interface from available WAN Interfaces: You can select this option to automatically get DNS server information from the selected WAN interface. Use the following Static DNS IP Address: You can select this option to manually enter the primary and /or optional secondary DNS server IP addresses provided by your ISP.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-14 Remove All: Click Remove All, then all the interface in the table will be deleted. Remove: Select the check box in the table above and then click Remove, the corresponding interface will be deleted in the table. 4.5.2.2 ATM-EoA-IPoE If your ISP provides an IPoE connection and you need to use an ATM Interface, follow the steps below to add a WAN service over a selected ATM interface: 1.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide information, and also the vendor-specific options. In some cases, the modem router is implemented to perform user-defined operations (as shown below). You can implement your own treatment of all such options. 2) If the modem router is functioning as a DHCP client, it must identify itself in option 61 (client-identifier) in every DHCP message. DUID/IAID is portion of option 61.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Enable IGMP Multicast: This is disabled by default. This setting will not allow IGMP (Internet Group Management Protocol) packets to be forwarded to the LAN. IGMP is used to manage multicasting on TCP/IP networks. Most users will not need to enable this. Some ISPs use IGMP to perform remote configuration for client devices, such as the router. If you are unsure, check with your ISP.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 8. On the next screen (as shown Figure 4-19) you will see the detailed settings you’ve made. Please click the Apply/Save button to save these settings. Figure 4-19 4.5.2.3 ATM-EoA-Bridging If you want to adopt the Bridge service and you need to use an ATM Interface, follow the steps below to add a WAN service over a selected ATM interface: 1. Add a new ATM interface and select EoA option for DSL Link Type (see 4.5.1.1 ATM Interface). 2.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 2. Click the Add button on the screen Figure 4-7 and the next configuration is similar to IPoE (see section 4.5.2.2 ATM-EoA-IPoE). The difference is that you have to manually set the Static IP Address on the screen of Figure 4-15, and the Static IP Address for DNS Server on the screen of Figure 4-18. Note: ETH and ATM service can not coexist.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-20 Location: The location where you're enjoying the 3G card. Mobile ISP: The ISP (Internet Service Provider) you apply to for 3G service. The modem router will show the default Dial Number and APN of that ISP. Note: If your Location or Mobile ISP is not listed, please untick the box before Automatically fill ISP Information. Then fill the Dial Number and APN blanks below.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-21 Click Modem Settings in Figure 4-20, 3G Modem settings can be shown as below. Figure 4-22 To upload 3G USB Modem Configuration File: 1. Click the Add button. Then Figure 4-23 will pop up. 2. Click the Browse button in Figure 4-23, and then select the right file from the drop-down list. Click the Upload Settings button to upload the file.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-24 PPP Username/Password: Enter the Username and Password provided by your ISP. These fields are case-sensitive. Use Static IPv4 Address: If your ISP specifies an IP address for you, click the checkbox and fill the Static IPv4 Address. Use Static DNS IP Address: If your ISP specifies a DNS IP address for you, click the checkbox and fill the Primary DNS and Secondary DNS blanks below. The Secondary DNS is optional.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-26 Type the new value for the WAN Interface who’s MAC Address you want to change. You can select corresponding WAN Interface from the drop-down list and click Clone button to clone your current PC MAC. Click Restore Default button to restore the WAN Interface’s default MAC Address. Note: Only the WAN Ports can use MAC Address Clone function. All the clone MAC addresses must not be the same with each other. 4.5.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-27 IP Address: You can configure the modem router’s IP Address and Subnet Mask for LAN Interface. • IP Address: Enter the modem router’s local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1. • Subnet Mask: Enter the modem router’s Subnet Mask, the default value is 255.255.255.0.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide • Leased Time (hour): The Leased Time is the amount of time in which a network user will be allowed connection to the modem router with their current dynamic IP address. Enter the amount of time, in hours, then the user will be “leased” this dynamic IP address. After the dynamic IP address has expired, the user will be automatically assigned a new dynamic IP address. The default is 24 hours.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-29 Interface Address (prefix length is required): Here enter the prefix length of your interface address. IPv6 LAN Applications: Select a type to assign IPv6 addresses to the computers in your LAN. DHCPv6 Server and RADVD are provided. For DHCPv6 Server: 1) If Stateless is selected, it doesn’t need to be configured. 2) If Stateful is selected, please complete the following parameters.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide For RADVD: 1) If Randomly Generate is selected, it doesn’t need to be configured. 2) If Statically Configure is selected, please complete the following parameters. • Prefix: Enter a value for the site prefix. Click Save/Apply to make the configuration take effect. 4.5.6 NAT NAT (Network Address Translation) allows you to share one WAN (Wide Area Network) IP address for multiple computers on your LAN (Local Area Network).
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-30 Virtual Server Table: The table indicates the information about the Virtual Server entries. • Server Name: This is the name of the Virtual Server. It is exclusive and must be filled in. • External Port Start: The base number of External Ports. You can type a service port or leave it blank. • External Port End: The end number of External Ports. You can type a service port or leave it blank.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-31 2. Select the Interface which you want to use from the drop-down list. 3. Select the service which you want to use from the drop-down list. If the list does not have the service you need, type the name of the custom service in the text box. 4. Type the IP Address of the computer in the Server IP Address text box. 5.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Some applications require that specific ports in the modem router's firewall should be opened for access by remote devices. Port Trigger dynamically opens up the 'Open Ports' in the firewall when an application on the LAN initiates a TCP/UDP connection to a remote device using the triggering ports. The modem router allows the remote party from the WAN side to establish new connections back to the application on the LAN side using the open ports.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-33 2. Select the application from the drop-down list. If the list does not have the application that you want, select the Custom application radio button, and type the name of the custom application in the text box. 3. Enter the Trigger Port Start, Trigger Port End, Open Port Start and Open Port End in the table, and then select the Trigger protocol and Open protocol, TCP, UDP or All. 4.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-34 To add a new DMZ Host: You can enter the computer's IP address and then click Save/Apply to activate the DMZ host you set on this page. Note: DMZ host forwards all the ports at the same time. Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP Address assigned to it because its IP Address may change while using the DHCP function. 4.5.6.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Choose “Advanced Setup”“Security”“IP Filtering”, you can configure Outgoing Filtering rules on the screen (shown in Figure 4-36). The Outgoing IP Filtering feature allows you to control some IP traffic from LAN to access to some specifically addresses. By default, all outgoing IP traffic from LAN is allowed, but some IP traffic can be BLOCKED by setting up filters. Figure 4-36 Set up an Outgoing IP Filtering rule: 1.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 4.5.7.2 MAC Filtering Choose “Advanced Setup”“Security”“MAC Filtering”, you can configure MAC Filtering rules on the screen as shown in Figure 4-38. The section allows you to control access to the Internet by users on your local network based on their MAC Address. Note: MAC Filtering is only effective on ATM PVC(s) configured in Bridging mode. Figure 4-38 Change Policy: There are two policies for the MAC filters: FORWARDED and BLOCKED.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 3. Enter Destination MAC Address and Source MAC Address in the text box. 4. Select Frame Direction in the drop-down list for the rule. 5. Select the WAN interfaces from the drop-down list. 6. Click Save/Apply to save this entry and then you will see your settings as shown in Figure 4-38. 4.5.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide other LAN devices, click Other MAC Address radio button and enter the MAC address of the other LAN device. 4. Select the day to allow the rule to take effect in the table. 5. Enter the Start Blocking Time and End Blocking Time in the text box separately, and then the device controlled will then be unable to connect to the internet during that time. 6.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 3. Click Save/Apply to save this entry and then you will see your settings as shown in Figure 4-42. Every computer connected to the modem router will not access this URL address on the port. 4.5.9 Quality of Service Choose “Advanced Setup”“Quality of Service”, you can enable QoS (Quality of Service) on the screen shown in Figure 4-44. QoS helps to prioritize data as it enters your modem router.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-45 Click the Add button in Figure 4-45, and you can configure the QoS queue entry on the next screen as shown in Figure 4-46. Figure 4-46 Name: Set a name for the entry. Enable: Select Enable option to take this entry effect. Interface: Assigned a specific Wan Service for this QoS queue entry. Queue Precedence: Specify precedence for this QoS queue entry.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 4.5.9.2 QoS Classification This section will guide you to create a traffic class rule to classify the upstream traffic, assign queue which defines the precedence and the interface and optionally overwrite the IP header DSCP byte. A rule consists of a class name and at least one condition below. All of the specified conditions in this classification rule must be satisfied for the rule to take effect.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-49 Enable Bandwidth Control: Check this box to enable the Bandwidth Control function. Total Upstream Bandwidth (Kbps): Enter the upload speed through the WAN port. Total Downstream Bandwidth (Kbps): Enter the download speed through the WAN port. Save/Apply: Click this button to make the configuration take effect. Note: The Total Upstream Bandwidth and Total Downstream Bandwidth are required to be configured. 4.5.10.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-51 Rule Status: Select the status of the rule from the drop-down list to enable or disable the rule. IP Range: Enter a single IP address or a range of IP addresses. Port Range: Enter a single port or a range of ports. Protocol: Select a protocol type from the drop-down list. TCP, UDP and ALL are available here. Priority: Select priority form the drop-down list.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide according to their min upstream/downstream rate. The greater a rule’s min upstream/downstream rate is, the more bandwidth it gets. 4.5.11 Routing Choose “Advanced Setup”“Routing”, it includes three menus: Default Gateway, Static Route and RIP. The detailed descriptions are provided below. 4.5.11.1 Default Gateway Choose “Advanced Setup”“Routing”“Default Gateway”, you can see the Default Gateway screen. Figure 4-53 4.5.11.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-55 2. Enter the following data: IP Version: Select the version of IP. Destination IP Address/prefix length: The Destination IP Address is the address of the network or host that you want to assign to a static route. Interface: Select the Interface name in the text box, or else, the default Use Interface will be adopted for the Static Route.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 4.5.12.1 DNS Server Choose “Advanced Setup”“DNS”“DNS Server”, and you can see the DNS Server Configuration screen as shown in Figure 4-57. Figure 4-57 For PPPoA, PPPoE enabled PVC(s), please select the Select DNS Server Interface from available WAN interfaces checkbox, this modem router will accept automatically the first received DNS assignment from the selected configured WAN interface during the connection establishment.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-58 To add a DDNS entry: 1. Click the Add button (pop-up after Figure 4-58), and then you will set the DDNS in the next screen (shown in Figure 4-59). Figure 4-59 2. Select D-DNS provider in the drop-down list. 3. Enter the Hostname of the DNS Server, and select the corresponding Interface for the DDNS, you can leave it default. 4. Type the User Name and Password for your DDNS account. Click Save/Apply to save your settings. 4.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-60 You can select the modulation type, phone line pair and the capability of Bitswap or SRA. After you set them up, click Save/Apply to save the configurations. 4.5.14 UPnP Choose “Advanced Setup”“UPnP”, you can Enable or Disable the UPnP (Universal Plug and Play) protocol on the screen.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-62 To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button will remove the grouping and add the ungrouped interfaces to the Default group. Only the default group has IP interface. To create a new interface group: 1. Click the Add button. You can add a new interface group in the next screen. Figure 4-63 2. Enter a unique name for Group. 3.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide specified vendor ID (DHCP option 60) will be denied an IP address from the local DHCP server. 4. Select interfaces from the available interface list and add it to the grouped interface list using the arrow buttons to create the required mapping of the ports. Note: These clients may obtain public IP addresses. 5. Click Save/Apply to make the entry effective immediately.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Associated WAN Interface: Select a WAN connection from the drop-down list. Only the connected WAN connections can be shown in the drop-down list. Associated LAN Interface: Select a LAN connection from the drop-down list. Only the connected LAN connections can be shown in the drop-down list. IPv4 Mask Length: The length of the selected WAN connection’s IPv4 mask. 6rd Prefix with Prefix Length: The length of the 6rd prefix.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Click Save/Apply to make the configuration take effect. Note: In this type, there should not have any IPv4 WAN connections. If there are IPv4 WAN connections, the page will prompt you to delete all the IPv4 WAN connections. 4.5.17 IPSec Choose “Advanced Setup”“IPSec”, you can Add/Remove or Enable/Disable the IPSec tunnel connections on the screen as shown in Figure 4-68.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Click Add New Connection in Figure 4-68 and then you will enter the screen shown in Figure 4-69. Figure 4-69 IPSec Connection Name: Enter a name for your VPN. Remote IPSec Gateway Address (IP or Domain Name): Enter the destination gateway IP address in the box which is the public WAN IP or Domain Name of the remote VPN server endpoint. (For example: Input 219.134.112.247 in Device1, Input 219.134.112.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide After complete the basic settings and click Save/Apply in both Device1 and Device2, PCs in LAN1 could conmmunicate with PCs in remote LAN2. (For example: You can ping the IP address of PC2 which is 192.168.2.100 in PC1) Note: The VPN Servers Endpoint from both ends must use the same pre-shared keys and Perfect Forward Secrecy settings. Click Show Advanced Settings and then you can configure the Advanced Settings.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Choose “Advanced Setup”“Multicast”, you can configure the IGMP protocol on the screen. Figure 4-70 Click Apply/Save to save your settings. 4.6 IPTV Choose “IPTV”, and you will see the screen as shown in Figure 4-71. Figure 4-71 Enable IPTV: Check this box to enable IPTV. If this checkbox is selected, please set the following parameters as shown in the figure below. Make sure the following settings are correct.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 4.7 Wireless Choose “Wireless”, there are six submenus to configure Wireless LAN settings. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.7.1 Basic Choose “Wireless””Basic”, you will see the screen of Wireless--Basic settings shown as below. The basic settings for wireless networking are set on this screen.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide be identical for all devices in the wireless network. Make sure this setting is the same for all stations in your wireless network. Type the desired SSID in the space provided. SSID2/3: The modem router can broadcast three SSIDs at most. Tick the box to enable SSID2 or SSID3 as needed. BSSID: Show the MAC address of the modem router. Country: Restrict the channel set and transmit power. Click Apply/Save to save your settings. 4.7.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 2) To build a successful connection by WPS, you should also do the corresponding configuration of the new device for WPS function meanwhile. I. By PBC If the wireless adapter supports WPS and the Push Button Configuration (PBC) method, you can add it to the network by PBC with the following two methods. Click Push-Button, you will see the screen as shown below. Figure 4-74 Method One: Hardware push button.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-75 Method Two: Step 1: Press the WPS button on the back panel of the modem router. Step 2: For the configuration of the wireless adapter, please choose “Push the button on my access point” in the configuration utility of the WPS as below, and click Next.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-76 Step 3: Wait for a while until the next screen appears. Click Finish to complete the WPS configuration. Figure 4-77 II. By PIN If the new device supports Quick Security Setup and the PIN method, you can add it to the network by PIN with the following two methods.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Method One: Enter the PIN of wireless adapter into my modem router. Step 1: Select the PIN checkbox and enter the PIN code of the wireless adapter in the field under as shown below. Then click Add Enrollee. Figure 4-78 Note: The PIN code of the adapter is always displayed on the WPS configuration screen.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-80 Step 2: For the configuration of the wireless adapter, please choose “Enter a PIN from my access point” in the configuration utility of the WPS as below, and enter the PIN code of the modem router into the field after “Access Point PIN”. Then click Next. Figure 4-81 4.7.2.2 Manual Setup AP Follow the instructions below to configure security features of the wireless LAN interface manually.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-82 Network Authentication: Select an authentication type from the drop-down list. Note: For most users, it is recommended to use the default Wireless LAN Performance settings. Any changes made to these settings may adversely affect your wireless network. Under certain circumstances, changes may benefit performance. Carefully consider and evaluate any changes to these wireless settings. 1.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-83 Figure 4-84 Encryption Strength: Select the appropriate level of encryption, 64-bit or 128-bit. Current Network Key: To indicate which WEP key to use, select a transmission key number. Network Key 1-4: If you want to manually enter the WEP keys, then enter them in the network Key 1-4 fields. Configure WEP Settings 1. Select Shared (good) from the Network Authentication drop-down list.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-85 Note: We use Network Authentication Shared (good), Encryption Strength 64-bit, Current Network Key “1” and enter 10 hexadecimal digits”1234567890” in the Network Key 1 for example, as shown in Figure 4-85 above.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 2. WPA-Enterprise WPA security for wireless communication has been developed to overcome some of the shortcomings of WEP. WPA combines the key generation with the authentication services of a RADIUS server. Figure 4-86 WPA Group ReKey Interval: Enter the Key Renewal period, which tells the modem router how often it should change encryption keys. RADIUS Server IP Address: The IP address of the RADIUS server.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-87 3. WPA-Personal WPA-Personal requires a shared key and does not use a separate server for authentication. PSK keys can be ASCII or Hex type. Figure 4-88 Wireless Network Key: Enter the key shared by the modem router and your other network devices. It must have 8-63 ASCII characters or 8-64 Hexadecimal digits. Click here to display: Click it to show you the WPA Pre-Shared Key. Configure WPA-Personal settings 1.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-89 Note: If you click the option “Click here to display”, the Figure 4-90 will pop-up, and it shows the password you have set. In addition, it won't show the blank characters in both ends of the password phrase. Figure 4-90 4. WPA2-Enterprise To configure WPA2-Enterprise settings, select the WPA2-Enterprise option from the drop-down list. The menu will change to offer the appropriate settings.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-91 WPA2 Preauthentication: Select Enable from the drop-down list, Stations will authenticate with the AP during the scanning process, and once association is required, the station has been already authenticated. Network Re-auth Interval: Enter a value in seconds as the frequency interval to enable periodic Network Re-authentication function, while leave it blank or enter “0” to disable it. 5.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-93 7. Mixed WPA2/WPA Personal To configure Mixed WPA2/WPA-Personal settings, select the Mixed WPA2/WPA Personal option from the drop-down list. The menu will change to offer the appropriate settings. The steps of this setting are the same with WPA-PSK. Figure 4-94 4.7.3 Wireless Schedule Choose menu “Wireless”“Wireless Schedule”, you can configure the Task Schedule as shown below. Please set the modem router’s system time first.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-95 Note: The time you set is the period you need the wireless off. Before configure the wireless schedule, please set system time first which refer to 4.10.5 Internet Time, then you can enable or disable Wireless Schedule. Apply To: Select the day or days you need the wireless off. Start Time, End Time: You can select all day-24 hours or you may enter the Start Time and End Time in the corresponding field.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s RADIUS. To filter wireless users by MAC Address, either permitting or blocking access. If you do not wish to filter users by MAC Address, select Disabled. Disabled: Select this option to disable MAC Filter function.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide • Access Point: Select this option to allow wireless stations including AP clients to access. • Wireless Bridge: Also known as WDS (Wireless Distribution System), it will bridges the wireless stations which also in bridge mode to connect two or more remote LANs. Bridge Restrict: • Disabled: Select this option to disables wireless bridge restriction, that any wireless bridge will be granted access.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-101 Channel: Select the channel you want to use from the drop-down List. This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. Mode: In the drop-down list you can select “11b”, “11bg”, “11bgn” and "11n only”. “11bgn” allows both 802.11b, 802.11g and 802.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Beacon Interval: Enter a value between 20-1000 milliseconds. The Beacon Interval value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the modem router to synchronize the wireless network. The default value is 100. Transmit Power: This option will allow you to configure the wireless transmit power.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-103 You can enable or disable Guest Network. When you enable this function, you could set wireless parameters for Guest Network. Guest SSID: The guest network name. When setting up a Guest network, it is strongly recommended to use a name that easily distinguishes it from your primary network. Authentication Type: Select the Authentication Type from the drop-down list. Encryption: You can select either AES or AES+TKIP.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-104 MAC: Displays the connected wireless station's MAC address. Associated: Displays whether the wireless station has associated with the access point. Authorized: Displays the information of Authentication. SSID: Displays the connected wireless station's SSID. You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click on the Refresh button. 4.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-105 Volume: The volume name of the USB drive the users have access to. File System: The system of the USB drive. Capacity: The storage capacity of the USB driver. Status: Indicates the shared or non-shared status of the volume. Active means volume can be shared, while Inactive means volume can not be shared..
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-106 To add a new user account, please follow the steps below: 1. Choose the index from the drop-down list of Choose Index. 2. Self-define a New Username. 3. Enter the password in the New Password field. 4. Re-enter the password in the Confirm Password field. Click the Set button, and then a new entry will be added in the table. 4.9.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Server Status: Indicates the Storage Sharing's current status. Anonymous access to all the volumes: This function is enabled by default, so users can access all activated volumes of Storage Sharing without accounts. If you want to add a shared folder which does not allow anonymous login, uncheck the box to disable this function. And Folder Table will be displayed as shown below. Figure 4-108 Share Name: This folder's display name.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 4. Click the Save/Apply button to apply the settings. You can click the upper button to go to the upper folder Click the Enable/Disable Selected button to enable or disable the selected entries. Click the Delete Selected button to delete the selected entries. Note: 1) The max share folders number is 10. If you want to share a new folder when the number has reached 10, you can delete an existing share folder and then add a new one.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide To add a new folder, follow the instructions below. 1. Click Add New Folder in Figure 4-110. Figure 4-111 2. Click the Browse button, and then select the Select Volume from the drop-down list. 3. Enter display name of the share folder in Share Name filed. 4. Click the Save/Apply button to apply the settings. You can click the upper button to go to the upper folder.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-112 Server Enable: Select this box to enable this function. Server Name: The name of this Media Server. To add a new share folder for your media server, please follow the instructions below: a) Click Add New Folder button, and you will see the screen as shown in Figure 4-113. Figure 4-113 b) Enter the name of the share folder in Share Name field. c) Click the Save/Apply button to apply the configuration.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide There are three states of the print server, they are as follows: Online: Indicates the print service has been turned on, and no user is using the print services at present. You can click the "Stop" button to stop the print service. Offline: Indicates the print service feature is disabled. You can click "Start" button to start the print service.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 4.11.1 Settings This section provides three important functions for managing the modem router: Export(Backup), Import(Update) and Restore Default. The detailed manipulations are described below. 4.11.1.1 Export Choose “Management”“Settings”“Export”, you can see the Export screen, this screen (shown in Figure 4-116) allows you to save the current configuration of the modem router as a backup file.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide TD-W8968 Figure 4-118 4.11.1.2 Import Choose “Management”“Settings”“Import”, you can see the Import screen, this screen (shown in Figure 4-119) allows you to update the modem router’s settings. Figure 4-119 To update the modem router’s settings: 1. Click the Browse button to locate the update file for the device, and you can also enter the exact path to the Setting file in the text box. 2.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 4.11.1.3 Restore Default Choose “Management”“Settings”“Restore Default”, you can see the Restore Default screen, this screen (shown in Figure 4-120) allows you to restore the modem router’s configuration to the factory defaults on the screen. Figure 4-120 Restore Default Settings: Click this button to restore the modem router’s configuration to the factory defaults, and then follow the on-screen instructions to complete it.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-122 Refresh: Click the button, the information in the table will be updated. Back: Click the button, the screen will back to the previous page. To configure the System Log settings: Click the Configure System Log button (shown in Figure 4-121), you will see the screen below (shown in Figure 4-123). Figure 4-123 Disable/Enable: Select the Enable to log the events, if you don’t want to log these events, please select Disable.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide An SNMP Agent is an application running on the router that performs the operational role of receiving and processing SNMP messages, sending responses to the SNMP manager, and sending traps when an event occurs. So a router contains SNMP "agent" software can be monitored and/or controlled by SNMP Manager using SNMP messages.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide TR-069（WAN Management Protocol）allows a Auto-Configuration Server (ACS) to perform auto-configuration, provision, collection, and diagnostics to this device. Figure 4-125 Inform: You can select the checkbox to disable or enable the Inform Interval. Inform Interval: Type the interval time of your modem router contact with the ACS. ACS URL: Please accept this information from your ISP.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 4.11.5 Internet Time Choose “Management”“Internet Time”, you can see the Time settings screen as shown below. Here you can configure the time of the modem router. Figure 4-126 Enable DST: Select the checkbox to enable daylight saving function. 4.11.6 Access Control There are two submenus under the Access Control menu: Passwords and Remote Access. The detailed explanations for each submenu are provided below. 4.11.6.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide To change the password: Figure 4-127 1. Select the Username whose password you want to change. 2. Enter the Old Password in the text box. 3. Enter the New Password and Confirm Password. The Confirm Password should be the same as the New Password. 4. Click Save/Apply to make your change take effect. Note: 1) Access to your DSL modem router is controlled through two user accounts: admin and user.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-128 Web：Select this box, you can access your modem router via web. Telnet: Select this box, you can access your modem router via command line. ICMP(ping): Select this box, PC in public network can ping the WAN address of the modem router. Click Save/Apply to make your change take effect. 4.11.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide 2. Click Browse to view the folders and select the image file or enter the exact path to the image file location in the text box. 3. Click the Update Firmware button. Note: 1) There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the modem router itself, you can try to upgrade the firmware.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Figure 4-131 102
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Appendix A: Specifications General Standards and Protocols Safety & Emissions ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5, IEEE 802.3, IEEE 802.3u, IEEE 802.11b , IEEE 802.11g , 802.11n TCP/IP, IPoA , PPPoA , PPPoE, SNTP, HTTP, DHCP, ICMP, NAT FCC, CE Four 10/100M Auto-Negotiation RJ45 ports（Auto MDI/MDIX) Ports One RJ11 port One USB 2.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Appendix B: Troubleshooting T1. What can I do if I don’t know or forget my password? 1) For default wireless password: Please refer to the “Wireless Password/PIN” labeled on the bottom of the modem router. 2) For the web management page password: Reset the modem router first and then use the default user name and password: admin/admin. T2.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide For Windows 8 Move your mouse to the lower right corner and you will see Search icon in the Popups. Go to “ -> Apps”. Type Control Panel in the search box and press Enter, then you will go to Control Panel. Click “View network status and tasks > Change adapter settings”. Right-click “Ethernet” and then select Properties. Double-click Internet Protocol Version 4 (TCP/IPv4).
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide T4. What can I do if I cannot access the Internet? 1) Check to see if all the connectors are connected well, including the telephone line, Ethernet cables and power adapter. 2) Check to see if you can log on to the web management page of the modem router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet.
TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Appendix C: Technical Support Technical Support For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq To download the latest Firmware, Driver, Utility and User Guide, go to: http://www.tp-link.com/en/support/download For all other technical support, please contact us by using the following details: Global Tel: +86 755 2650 4400 Fee: Depending on rate of different carriers, IDD. E-mail: support@tp-link.
