TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router Rev: 2.0.1 1910010531 Downloaded from www.Manualslib.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Industry Canada Statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
DECLARATION OF CONFORMITY For the following equipment: Product Description: 300Mbps Wireless N ADSL2+ Modem Router Model No.
CONTENTS Package Contents .................................................................................................... 1 Chapter 1 Introduction ......................................................................................... 2 1.1 Product Overview.................................................................................. 2 1.2 Main Features ....................................................................................... 2 1.3 Conventions ................................
4.5.2 Filter ........................................................................................................ 50 4.5.3 SNMP ...................................................................................................... 58 4.5.4 UPnP ....................................................................................................... 58 4.5.5 DDNS ...................................................................................................... 59 4.5.6 CWMP ............................
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Package Contents The following contents should be found in your package: ¾ One TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router ¾ One Power Adapter for TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router ¾ Quick Installation Guide ¾ One RJ45 cable ¾ Two RJ11 cables ¾ One ADSL splitter ¾ One Resource CD which includes this User Guide ) Note: Make sure that the package contains the above items.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 1 Introduction Thank you for choosing the TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router. 1.1 Product Overview The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet or IEEE 802.11n/ IEEE 802.11g/ IEEE 802.11b wireless network. The TD-W8961ND connects to an Ethernet LAN or computers via standard Ethernet ports.
TD-W8961ND ¾ 300Mbps Wireless N ADSL2+ Modem Router User Guide Supports PPPoE, it allows connecting the internet on demand and disconnecting from the Internet when idle. ¾ Provides reliable ESD and surge-protect function with quick response semi-conductive surge protection circuit. ¾ High speed and asymmetrical data transmit mode, provides safe and exclusive bandwidth. ¾ Supports All ADSL industrial standards. ¾ Compatible with all mainstreams DSLAM (CO).
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 2 Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs locate on the front panel. They indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name Status On (Power) Off On (ADSL) Flash Off On Flash (INTERNET) Indication The modem router is powered on. The modem router is off. Please ensure that the power adapter is connected correctly.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide enabled. Please refer to 4.3.3 WPS Settings for more information. On (LAN1-4) Flash Off There is a device connected to this LAN port. The modem router is sending or receiving data over this LAN port. There is no device connected to this LAN port. ) Note: 1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Router for more information about how to make Internet connection correctly.
TD-W8961ND 2.2 300Mbps Wireless N ADSL2+ Modem Router User Guide The Back Panel Figure 2-2 ¾ POWER: The Power plug is where you will connect the power adapter. ¾ ON/OFF: The switch for the power. ¾ WPS: The switch for the WPS function. For details, please refer to 4.3.3.1 Wireless-WPS Settings. ¾ RESET: There are two ways to reset the Router's factory defaults. Method one: With the Router powered on, use a pin to press and hold the Reset button for at least 5 seconds.
TD-W8961ND 2.3 300Mbps Wireless N ADSL2+ Modem Router User Guide Installation Environment ¾ The Product should not be located where it will be exposed to moisture or excessive heat. ¾ Place the Router in a location where it can be connected to the various devices as well as to a power source. ¾ Make sure the cables and power cord are safely placed out of the way so they do not create a tripping hazard. ¾ The Router can be placed on a shelf or desktop.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 2-3 8 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 3 Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD-W8961ND or connect your adapter to a Hub/Switch which has connected to the Router, you need to configure your PC’s IP address. Follow the steps below to configure it.. Step 1: Click the Start menu on your desktop, right click My Network Places, and then select Properties (shown in Figure 3-1).
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. Figure 3-3 10 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK. Figure 3-4 ) Note: You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically” and “Obtain DNS server address automatically” in the screen above. Now, you can run the Ping command in the command prompt to verify the network connection.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide If the result displayed is similar to the screen shown below, it means that your PC has not connected to the Router. Figure 3-6 You can check it follow the steps below: 1) Is the connection between your PC and the Router correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the Router's IP address is 192.168.1.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button. Figure 3-8 Step 2: Configure the time for the Router, and then click the NEXT button. Figure 3-9 Step 3: Select the connection type to connect to the ISP (We select PPPoE/PPPoA mode for example here), and then click the NEXT button.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-11 Step 5: Configure the rules for the WLAN, and click NEXT. Figure 3-12 ) Note: If the Access Point is activated, the wireless function will be available even without the external antenna because of an additional printed antenna. To adopt the wireless security protection measures, please refer to section 4.3.3. Step 6: Click NEXT to finish the Quick Start. Figure 3-13 14 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 4 Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe you will get help from this chapter to configure the advanced settings through the Web-based Utility. After your successful login, you can configure and manage the device.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-2 ) Note: Click the other submenus System Log or Statistics in Figure 4-2, and you will be able to view the system log and traffic statistics about the Router. 4.1.2 System Log Choose “Status→System Log” menu, and you will be able to query the logs of the Router. 16 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-3 The Router can keep logs of all traffic. You can query the logs to find what happened to the Router. Click the CLEAR LOG button to clear the logs. Click the SAVE LOG button to save the logs. 4.1.3 Statistics Choose “Status→Statistics” menu, and you will be able to view the network traffic over Ethernet, ADSL and WLAN. 17 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-4 ¾ Interface: You can select Ethernet, ADSL and WLAN to view the corresponding network traffic over different ports. ¾ Select Ethernet, and you will see the statistics table as below. Statistics Table: Transmit Frames Transmit Multicast Frames Transmit Statistics Transmit total Bytes Transmit Collision Transmit Error Frames The multicast frames transmitted over the Ethernet port.
TD-W8961ND ¾ 300Mbps Wireless N ADSL2+ Modem Router User Guide Select ADSL, and you will see the statistics table as below. Statistics Table: Transmit Statistics Receive Statistics ¾ The total PDUs transmitted over the ADSL port. Transmit total PDUs Transmit total Error Counts The total errors occurred over the ADSL port when data is being transmitted. The total PDUs transmitted over the ADSL port.
TD-W8961ND 4.3 300Mbps Wireless N ADSL2+ Modem Router User Guide Interface Setup Choose “Interface Setup”, you can see the next submenus: Internet and LAN. Figure 4-5 Click any of them, and you will be able to configure the corresponding function. 4.3.1 Internet Back to LED Explanation Choose “Interface Setup→Internet” menu, you can configure the parameters for WAN ports in the next screen (shown in Figure 4-6). Figure 4-6 ¾ ATM VC: ATM settings are used to connect to your ISP.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide • Status: If you want to use a designed VC, you should activate it. • VPI: Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255. Please input the value provided by your ISP. • VCI: Identifies the virtual channel endpoints in an ATM network. The valid range is from 32 to 65535 (1 to 31 is reserved for well-known protocols). Please input the value provided by your ISP.
TD-W8961ND ¾ 300Mbps Wireless N ADSL2+ Modem Router User Guide Default Route: If enable this function, the current PVC will be considered as the default gateway to internet from this device. ¾ TCP MTU Option: Enter the TCP MTU as your desire. ¾ Dynamic Route: Select this option to specify the RIP (Routing Information protocol) version for WAN interface, including RIP1, RIP2-B and RIP2-M.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide ) Note: Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets separated by a dot (x.x.x.x), such as 192.168.1.100. The Router will not accept the IP address if it is not in this format. 3) PPPoA/PPPoE Select this option if your ISP requires you to use a PPPoE connection. This option is typically used for DSL services.
TD-W8961ND ¾ 300Mbps Wireless N ADSL2+ Modem Router User Guide Connection: For PPPoA/PPPoE connection, you can select Always on or Connect on-Demand or Connect Manually. Connect on demand is dependent on the traffic. If there is no traffic (or Idle) for a pre-specified period of time), the connection will tear down automatically. And once there is traffic send or receive, the connection will be automatically on.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-11 ¾ Router Local IP: These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. • IP Address: Enter the Router’s local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1.
TD-W8961ND • 300Mbps Wireless N ADSL2+ Modem Router User Guide Multicast: Select IGMP version, or disable the function. IGMP (Internet Group Multicast Protocol) is a session-layer protocol used to establish membership in a multicast group. The ADSL ATU-R supports both IGMP version 1 (IGMP v1) IGMP v2 and IGMP v3. Select “Disabled” to disable it. • ¾ IGMP Snoop: Enable the IGMP Snoop function if you need. DHCP Server: Select Enabled, then you will see the screen below (shown in Figure 4-12).
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide • Hostname: Display the name of the DHCP client. • IP Address: Display the IP Address of the DHCP client. • MAC Address: Display the MAC Address of the DHCP client. • Status: Display the status of the assigned IP Address, either Static or Auto. Static indicates that the IP Address is bounded to the MAC Address, while Auto indicates that the IP Address is assigned to the MAC Address automatically.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide ) Note: If you select Disabled, the DHCP function will not take effect. 4.3.3 Wireless Choose “Interface Setup→Wireless” menu, and you will see the Wireless screen (shown in Figure 4-14 ). Please configure the parameters for wireless according to the descriptions below. 28 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-14 29 Downloaded from www.Manualslib.
TD-W8961ND ¾ 300Mbps Wireless N ADSL2+ Modem Router User Guide Access point Settings: These are the settings of the access point. You can configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network. • Access point: Select Activated to allow wireless station to associate with the access point. • Channel: Select the channel you want to use from the drop-down List of Channel. This field determines which operating frequency will be used.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide • Extension Channel: If “20/40 MHz” is selected, this option will be displayed. • Guard Interval: Select the guard interval you want from the drop-down list. • MCS: Select the wireless transmission rate from the drop-down list. By default, the option is AUTO. ¾ Multiple SSIDs Settings: These are the settings of the SSID. • SSID Index: The index of the SSID, and in this model, you can only leave it as a default value of 1.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-16 2) WEP-128Bits To configure WEP-128Bits settings, select the WEP-128Bits option from the drop-down list. The menu will change to offer the appropriate settings. 128-bit is stronger than 64-bit. Figure 4-17 3) WPA-PSK To configure WPA-PSK settings, select the WPA-PSK option from the drop-down list. The menu will change to offer the appropriate settings.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-18 ¾ Encryption: Select the encryption you want to use: TKIP/AES, TKIP or AES (AES is an encryption method stronger than TKIP). • TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted. • AES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block data encryption.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-20 ¾ WPS Settings: WPS can help you to add a new wireless device to an existing network quickly. This section will guide you how to use WPS function. • WPS state: Display the current WPS state.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 2: Press and hold the WPS button of the adapter directly for 2 or 3 seconds. Step 3: Wait for a while until the next screen appears. Click Finish to complete the WPS configuration. The WPS Configuration Screen of Wireless Adapter Method Two: Step 1: Press the WPS button on the black panel of the Router or click Start WPS button in Figure 4-21.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide The WPS Configuration Screen of Wireless Adapter Step 3: Wait for a while until the next screen appears. Click Finish to complete the WPS configuration. The WPS Configuration Screen of Wireless Adapter 2) PIN code If the wireless adapter supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods. Click PIN code, you will see the screen as shown below. 36 Downloaded from www.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-22 Method One: Enter the PIN into my Router Step 1: For the configuration of the wireless adapter, please choose “Enter a PIN into my access point or a registrar” in the configuration utility of the WPS, and get the PIN code on the screen as below, then click Next.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-23 Method Two: Enter the PIN from my Router Step 1: Get the Current PIN code of the Router from AP self PIN code in Figure 4-23 (each Router has its unique PIN code. Here takes the PIN code 55924054 of this Router for example).
TD-W8961ND • 300Mbps Wireless N ADSL2+ Modem Router User Guide SSID: Wireless network name shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters (use any of the characters on the keyboard). Make sure this setting is the same for all stations in your wireless network. Type the desired SSID in the space provided.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-25 ¾ Firewall: Select this option can automatically detect and block Denial of Service (DoS) attacks, such as Ping of Death, SYN Flood, Port Scan and Land Attack. ¾ SPI: If you enable SPI, all traffics initiated from WAN would be blocked, including DMZ, Virtual Server, and ACL WAN side. 4.4.2 Routing Choose “Advanced Setup→Routing” menu, and you will see the routing information in the next screen (shown in Figure 4-26).
TD-W8961ND ¾ 300Mbps Wireless N ADSL2+ Modem Router User Guide Gateway IP Address: Enter the IP address of the gateway. The gateway is an immediate neighbor of your ADSL Router that will forward the packet to the destination. On the LAN, the gateway must be a router on the same segment as your Router; over Internet (WAN), the gateway must be the IP address of one of the remote nodes. ¾ Metric: Metric represents the "cost" of transmission for routing purposes.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.3.1 DMZ Choose “Advanced Setup→NAT→DMZ” in Figure 4-28, you can configure the DMZ host in the next screen. A DMZ (demilitarized zone) is a host between a private local network and the outside public network. It prevents outside users from getting direct access to a server that has company data. Users of the public network outside the company can access to the DMZ host.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide example, if you want to set the FTP Virtual server, you can set the start and end port number to 21. ¾ Local IP Address: Enter the IP Address for the Virtual Server in LAN side. ¾ Virtual Server Listing: This displays the information about the Virtual Servers you establish. To add a virtual server entry: Step 1: Select the “Virtual Circuit” and select “Virtual Server”.
TD-W8961ND ¾ 300Mbps Wireless N ADSL2+ Modem Router User Guide Local Start & End IP: Enter the local IP Address you plan to map to. Local Start IP is the starting local IP address and Local End IP is the ending local IP address. If the rule is for all local IPs, then the Start IP is 0.0.0.0 and the End IP is 255.255.255.255. ¾ Public Start & End IP: Enter the public IP Address you want to do NAT. Public Start IP is the starting public IP address and Public End IP is the ending public IP address.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-32 ¾ QoS: Select this option to Activate/Deactivate the IP QoS on different types (IP ToS and DiffServ). ¾ Summary: Click the button to view the configurations of QoS. ¾ Rule: Configure the rules for QoS. If the traffic complies with the rule, then the Router will take the corresponding action to deal with it. • Rule Index: Select the index for the rule you want to configure. • Active: Activate the rule.
TD-W8961ND • 300Mbps Wireless N ADSL2+ Modem Router User Guide Source MAC & IP & Mask & Port Range: Enter the IP information about the Source host for the rule. • Protocol ID: Select one among TCP/UDP, TCP, UDP or ICMP protocols for the application. • Vlan ID Range: Enter the Vlan range, and the rule will be effective to the selected Vlans. • IPP/DS Field: Select the type of the action to assign the priority. When you select IPP/TOS, you can assign the priority via IP information.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-33 1) Assign VLAN PVID for each Interface Click Assign VLAN PVID for each Interface in Figure 4-33, you can assign the PVID for each interface in the next screen (shown in Figure 4-34). Figure 4-34 ¾ PVID: Each physical port has a default VID called PVID (Port VID). PVID is assigned to untagged frames or priority tagged frames (frames with null (0) VID) received on this port.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-35 ¾ VLAN Index: Select the VLAN index for this VC. You can specify 8 groups in maximum. ¾ VLAN ID: This indicates the VLAN group. ¾ ATM VCs: Select the ATM VCs as members of VLAN, and if you leave the Tagged blank, the tag in frames will be deleted when transmitted from the VC. ¾ Ethernet: Select the Ethernet port as a member of VLAN.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-36 ¾ ADSL Mode: Select the ADSL operation mode which your ADSL connection uses. ¾ ADSL Type: Select the ADSL operation type which your ADSL connection uses. 4.5 Access Management Choose “Access Management”, you can see the next submenus: Figure 4-37 Click any of them, and you will be able to configure the corresponding function. 4.5.1 ACL Choose “Access Management→ACL”, you can see the next screen (shown in Figure 4-38).
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-38 ¾ ACL: If Activated, the IP addresses which are contained in the Access Control List can access to the Router. If Deactivated, all IP addresses can access to the Router. ¾ ACL Rule Index: Select the ACL rule index for the entry. ¾ Active: Enable the ACL rule. ¾ Secure IP Address: Select the IP addresses which are permitted to access to the Router remotely. With the default IP 0.0.0.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-39 ¾ Filter Type Selection: Select the filter type for the configuration below. ¾ IP/MAC Filter Set Index: Select the Set index for the IP Filter entry. This index can match with six IP / MAC Filter Rule Indexes. ¾ Interface: Select the interface for the entry. ) Note: If select PVC0~PVC7 as an interface, the filter will match the IP traffic of WAN port with specified IPs (Source IP Address and Destination IP Address).
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide ) Note: Incoming means that IP traffic which is coming into the router, and the Outgoing means that IP traffic which is going out the router. ¾ IP/MAC Filter Rule Index: Select the Rule index for the IP Filter entry. ) Note: You should set the IP/MAC Filter Set Index and IP/MAC Filter Rule Index together to appoint the address (shown in the Filter List) for the IP Filter rule.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide ) Note: If you want to make the rule take effect, please select Yes to active the rule. Step 3: Enter the “Source IP Address”, “Destination IP Address”, “Subnet Mask” and “Port Number” in the corresponding field. Step 4: Select the Protocol as “TCP” and select the Unmatched rule as “Next”. Step 5: Finally, click the SAVE to save the entry. Step 6: Go to Step 2 to configure the next two rules: Block E-mail received by the IP address 192.168.1.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.5.2.2 MAC Filter Select IP/MAC Filter as the Filter type, and select MAC as the Rule type (shown in Figure 4-40), and then you can configure the filter rules based on MAC address. Figure 4-40 ¾ Rule Type: Select MAC for the MAC Filter rule. ¾ Active: Select “Yes” to make the rule to take effect. ¾ MAC Address: Enter the MAC address for the rule.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Select the “MAC” as the Rule Type on the Filter screen (show in Figure 4-40). , Then you can configure the specific rule for the example. Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then select the Interface “PVC0”, and select the Direction “Outgoing” for the first rule. ) Note: If you want to make the rule take effect, please select Yes to active the rule.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-41 ¾ Filter Type Selection: Select the Application Filter for the next configuration. ¾ Application Filter: Activate or deactivate the function. ¾ ICQ & MSN & YMSG & Real Audio/Video: Select Allow or Deny for these applications. If you select Allow, the Router will accept the application; if you select Deny, the Router will forbid the application. 4.5.2.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-42 ¾ Filter Type Selection: Select the URL Filter for the next configuration. ¾ Active: Select “Yes” to make the rule to take effect. ¾ URL Index: Select the index for the URL Filter entry. ¾ URL: Enter the URL for this URL Filter. ¾ URL Filter Listing: This displays the information about the URL Filter rules. To add a URL filter entry: For example: If you want to forbid the user to access the website: www.yahoo.com.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.5.3 SNMP Choose “Access Management→SNMP”, you can see the SNMP screen. The Simple Network Management Protocol (SNMP) is used for exchanging information between network devices. Figure 4-43 ¾ Get Community: Set the password for the incoming Get and Get next requests from the management station. ¾ Set Community: Set the password for incoming Set requests from the management station. 4.5.
TD-W8961ND ¾ 300Mbps Wireless N ADSL2+ Modem Router User Guide Auto-Configure: If you activate the function, then the UPnP network devices can automatically configure network addressing, announce their presence in the network to other UPnP devices and enable exchange of simple product and service descriptions. 4.5.5 DDNS Choose “Access Management→DDNS”, you can configure the DDNS function in the screen (shown in Figure 4-45). The router offers a Dynamic Domain Name System (DDNS) feature.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-46 ¾ CWMP: Select activate the CWMP function. ¾ URL: Enter the website of ACS which is provided by your ISP. ¾ User Name/Password: Enter the User Name and password to login the ACS server. ¾ Path: Enter the path that connects to the ACS server. ¾ Port: Enter the port that connects to the ACS server. ¾ User Name/Password: Enter the User Name and Password that provided the ACS server to login the router.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.6.1 Administration Choose “Maintenance→Administration”, you can set new password for admin in the screen (shown in Figure 4-48). Figure 4-48 ) Note: 1) 2) There is only one account that can access Web-Management interface. The default account is "admin", and the password is "admin". Admin has read/write access privilege.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-49 ) Note: The ADSL Router built-in some NTP Servers, when the Router connects to the Internet, the Router will get the system time automatically from the NTP Server. You can also configure the NTP Server address manually, and then the Router will get the time from the specific Server firstly. 2) PC’s Clock Select PC’s Clock as the Synchronize time, you don’t need to set any items.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-51 4.6.3 Firmware Choose “Maintenance→Firmware”, you can upgrade the firmware of the Router in the screen (shown in Figure 4-52). Make sure the firmware or romfile you want to use is on the local hard drive of the computer. Click Browse to find the local hard drive and locate the firmware or romfile to be used for upgrade.
TD-W8961ND 3) 300Mbps Wireless N ADSL2+ Modem Router User Guide The router will reboot after the upgrading has been finished. To back up the Router’s current settings: Step 1: Click the ROMFILE SAVE button (shown in Figure 4-52), click Save button in the next screen (shown in Figure 4-53) to proceed. Figure 4-53 Step 2: Save the file as the appointed file (shown in Figure 4-54).
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 2: Click the UPGRADE button to complete. 4.6.4 SysRestart Choose “Maintenance→SysRestart”, you can select to restart the device with current settings or restore to factory default settings in the screen (shown in Figure 4-55). Figure 4-55 4.6.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-56 4.7 Help Choose “Help”, you can view the help information for configuration of any function. 66 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-57 ) Note: Click the tab, and you will be able to get the corresponding information. 67 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Appendix A: Specifications General ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5, Standards and Protocols IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Appendix B: Troubleshooting 1. How do I restore my Router’s configuration to its factory default settings? With the Router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it. ) Note: Once the Router is reset, the current configuration settings will be lost and you will need to re-configure the router. 2.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Click Network Connections Right-click Local Area Connection Click Properties 70 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Double-click Internet Protocol (TCP/IP) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 71 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Click OK 72 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide For Windows Vista OS Go to Start > Settings >Control Panel, and then you will see the following page. Click View network status and tasks Click View status Click Properties 73 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 74 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide For Windows 7 OS Go to Start > Settings > Control Panel, and then you will see the following page. Click View network status and tasks Click Change adapter settings Right-click Local Area Connection Click Properties 75 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 76 Downloaded from www.Manualslib.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 2) Configure your IE browser Open your IE browser, click Tools tab and you will see the following screen. Click Internet Options Select Never dial a connection Click OK Now, try to log on to the Web-based configuration page again after the above settings have been configured.
TD-W8961ND 2) 300Mbps Wireless N ADSL2+ Modem Router User Guide Check to see if you can log on to the web management page of the Modem Router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step. 3) Consult your ISP and make sure all the VPI/VCI, Connection Type, account username and password are correct.
TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Appendix C: Technical Support Technical Support For more troubleshooting help, go to: www.tp-link.com/support/faq.asp To download the latest Firmware, Driver, Utility and User Guide, go to: www.tp-link.com/support/download.asp For all other technical support, please contact us by using the following details: Global Tel: +86 755 26504400 E-mail: support@tp-link.
