Note Please use only wired network connections to configure the Router. Power down all of your network devices, including your computer(s) and the Modem Router. If you currently use a modem, disconnect it now - the Modem Router will replace your current modem. Connect your computer to the LAN port on the Modem Router with an Ethernet cable.
Plug the provided Power Adapter into the Power jack on the back of the Modem Router and the other end to a standard electrical wall socket. Power on all your network devices and then check to see if the LEDs of the Router display normally as the diagram below describes.
Insert the provided Resource CD into your CD-ROM drive. The Setup Wizard will automatically pop up on your computer’s screen. Please select your product model and click Start Setup Then a flash video will pop up and show you how to connect your devices. After that, the Easy Setup Assistant will start. Click START, and then follow the step-by-step instructions until you complete the configuration The configuration has now been completed. Please skip to Step 3 “Testing the Internet Connection”.
Login Open your web browser and type in http://192.168.1.1/ in the address bar and press Enter A dialog box will prompt you for the User name and Password. Enter the default values and click OK. User name: admin Password: admin Click OK Note If the dialog box does not pop up, please refer to T3 in the Troubleshooting guide. T2 will help you if you forget the password. The web management page will display after a successful login.
Internet Parameters Configuration This page will then display. Enter the VPI and VCI values given by your ISP Choose the WAN Link Type given by your ISP. If PPPoE/PPPoA is selected, please proceed to A; If IPoE is selected, please skip to B; If IPoA is selected, please skip to C; If Bridge is selected, please skip to D Note If you did not get the VPI, VCI and WAN Link Type information, please contact your ISP for this information.
Note If you did not get the PPP Username or PPP Password, please contact your ISP for this information. Note The configuration for PPPoA is similar to that of PPPoE. After completing the above configuration, please proceed to Configuration. B. Wireless Configuration for IPoE If WAN IP Address, Subnet Mask, Gateway IP Address and DNS are provided by your ISP, check the Static IP and Set DNS Manually boxes and enter them into the corresponding blanks.
D. Configuration for Bridge Mode Click Next After completing the above configuration, please proceed to Configuration. Wireless Wireless Configuration Create a unique and easy to remember name for your wireless network. You can also keep the default setting without the device being affected Select a Network Authentication (here takes Mixed WPA2/WPA-PSK Personal for example) Create a Security Key using 8-64 characters Click Save Note The wireless security is Disabled by default.
Quick Setup – Finish To continue, the following page will be displayed. Click Reboot Now, your Modem Router has been configured and is rebooting. Please do not turn off the Modem Router while it’s rebooting. The basic settings for your Router are completed. Please open the web browser and log on to the following websites: http://www.tp-link.com http://www.google.
T1. How do I restore my Router’s configuration to its factory default settings? With the Router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it. Press it for 8 to 10 seconds Note Once the Router is reset, the current configuration settings will be lost and you will need to re-configure the Router. T2. What can I do if I don’t know or forgot my password? 1) Restore the Router’s configuration to its factory default settings.
Click Network Connections Right-click Local Area Connection Click Properties Double-click Internet Protocol (TCP/IP) 10
Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK Click OK 11
For Windows Vista OS Go to Start > Settings >Control Panel, and then you will see the following page.
Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 13
For Windows 7 OS Go to Start > Settings > Control Panel, and then you will see the following page.
Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 15
2) Configure your IE browser Open your IE browser, click Tools tab and you will see the following screen. Click Internet Options Select Never dial a connection Click OK Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your Router’s factory default settings and reconfigure your Router following the instructions of this QIG.
2) Consult your ISP and make sure all the VPI/VCI, Connection Type, account username and password are correct. If there are any mistakes, please correct the settings and try again. 3) If you still cannot access the Internet, please restore your Router to its factory default settings and reconfigure your Router by following the instructions of this QIG. 4) Please feel free to contact our Technical Support if the problem still exists.
Technical Support For more troubleshooting help, go to: www.tp-link.com/support/faq.asp To download the latest Firmware, Driver, Utility and User Guide, go to: www.tp-link.com/support/download.asp For all other technical support, please contact us by using the following details: Global Tel: +86 755 26504400 E-mail: support@tp-link.com Service time: 24hrs, 7days a week Singapore Tel: +65 62840493 E-mail: support.sg@tp-link.
