TP-LINK TECHNOLOGIES CO., LTD TD-8816 ADSL2+ Modem Router Rev:2.0.
TP-LINK TECHNOLOGIES CO., LTD COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
TP-LINK TECHNOLOGIES CO., LTD FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications.
TP-LINK TECHNOLOGIES CO., LTD Safety Information When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. Avoid water and wet locations.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: ADSL2+ Modem Model No.
CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Introduction ........................................................................................ 2 1.1 Product Overview ...................................................................................................... 2 1.2 Main Features ........................................................................................................... 2 1.
4.6 4.7 Maintenance............................................................................................................ 42 4.6.1 Administration.................................................................................................................43 4.6.2 Time Zone ......................................................................................................................43 4.6.3 Firmware.......................................................................................
TD-8816 ADSL2+ Modem Router User Guide Package Contents The following items should be found in your package: One TD-8816 ADSL2+ Modem Router One Power Adapter for TD-8816 ADSL2+ Modem Router Quick Installation Guide One RJ45 cable Two RJ11 cables One ADSL splitter One Resource CD , including: This User Guide Other Helpful Information Note: Make sure that the package contains the above items.
TD-8816 ADSL2+ Modem Router User Guide Chapter 1. Introduction Thank you for choosing the TD-8816 ADSL2+ Modem Router . 1.1 Product Overview The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet network. The Router is easy to use. The TD-8816 connects to an Ethernet LAN or computers via standard Ethernet ports. The ADSL connection is made using ordinary telephone line with standard connectors.
TD-8816 ADSL2+ Modem Router User Guide Real-time Configuration and device monitoring. Supports Multiple PVC (Permanent Virtual Circuit). Built-in DHCP server. Built-in firewall, supports IP/MAC filter, Application filter and URL filter. Supports Virtual Server, DMZ host and IP Address Mapping. Supports Dynamic DNS, UPnP and Static Routing. Supports system log and flow Statistics. Supports firmware upgrade and Web management. 1.
TD-8816 ADSL2+ Modem Router User Guide Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs locate on the front panel, which indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name Power LAN ADSL Internet Status Indication On The modem router is powered on. Off The modem router is off. Please ensure that the power adapter is connected correctly. On There is a device connected to this LAN port.
TD-8816 2.2 ADSL2+ Modem Router User Guide The Back Panel Figure 2-2 ON/OFF: The switch for the power. POWER: The Power plug is where you will connect the power adapter. LAN: Through the port, you can connect the Router to your PC or the other Ethernet network devices. RESET: There are two ways to reset the Router's factory defaults. Method one: With the Router powered on, use a pin to press and hold the Reset button (about 5 seconds) until the SYS LED becomes quick-flash from slow-flash.
TD-8816 ADSL2+ Modem Router User Guide • PHONE: Connect to the phone sets • MODEM: Connect to the ADSL LINE port of TD-8816 Plug one end of the twisted-pair ADSL cable into the ADSL LINE port on the rear panel of TD-8816. Connect the other end to the MODEM port of the external splitter. Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s Ethernet port or a regular hub/switch port, and the other end to the LAN port on the TD-8816. Step 3: Attach the power adapter.
TD-8816 ADSL2+ Modem Router User Guide Chapter 3. Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD-8816 or connect your adapter to a Hub/Switch which has connected to the Router, you need to configure your PC’s IP address. Follow the steps below to configure it. Step 1: Click the Start menu on your desktop, right click My Network Places, and then select Properties (shown in Figure 3-1).
TD-8816 ADSL2+ Modem Router User Guide Figure 3-3 Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK.
TD-8816 ADSL2+ Modem Router User Guide Note: You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically” and “Obtain DNS server address automatically” in the screen above. Now, you can run the Ping command in the command prompt to verify the network connection. Please click the Start menu on your desktop, select run tab, type cmd in the field, and then type ping 192.168.1.1 on the next screen, and then press Enter.
TD-8816 ADSL2+ Modem Router User Guide After that, you will see the screen shown below, enter the default User Name admin and the default Password admin, and then click OK to access to the Quick Start screen. You can follow the steps below to complete the Quick Setup. Figure 3-7 Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button. Figure 3-8 Step 2: Configure the time for the Router, and then click the NEXT button.
TD-8816 ADSL2+ Modem Router User Guide Step 3: Select the connection type to connect to the ISP (We select PPPoE/PPPoA mode for example here), and then click the NEXT button. Figure 3-10 Step 4: Configure the following options provided by your ISP: Username, Password, VPI, VCI and Connection Type. Then click NEXT. Figure 3-11 Step 5: Click NEXT to finish the Quick Start.
TD-8816 ADSL2+ Modem Router User Guide Chapter 4. Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe you will get help from this chapter to configure the advanced settings through the Web-based Utility. After your successful login, you can configure and manage the device.
TD-8816 ADSL2+ Modem Router User Guide Figure 4-2 4.1.2 System Log Choose “Status→System Log” menu, and you will be able to query the logs of the Router.
TD-8816 ADSL2+ Modem Router User Guide Figure 4-3 The Router can keep logs of all traffic. You can query the logs to find what happened to the Router. Click the CLEAR LOG button to clear the logs. Click the SAVE LOG button to save the logs. 4.1.3 Statistics Choose “Status→Statistics” menu, and you will be able to view the network traffic over Ethernet, and ADSL. Figure 4-4 Interface: You can select Ethernet and ADSL to view the corresponding network traffic over different ports.
TD-8816 ADSL2+ Modem Router User Guide Select Ethernet, and you will see the statistics table as below. Statistics Table: Transmit Frames Transmit Multicast Frames Transmit Transmit total Bytes Statistics Transmit Collision Transmit Error Frames Receive Statistics The multicast frames transmitted over the Ethernet port. The total bytes transmitted over the Ethernet port. The collision occurred over the Ethernet port when data is being transmitted.
TD-8816 4.2 ADSL2+ Modem Router User Guide Quick Start Please refer to 3.2 Login. 4.3 Interface Setup Choose “Interface Setup”, you can see the next submenus: Internet and LAN. Figure 4-5 Click any of them, and you will be able to configure the corresponding function. 4.3.1 Internet Choose “Interface Setup→Internet” menu, you can configure the parameters for WAN ports in the next screen (shown in Figure 4-6). Figure 4-6 ATM VC: ATM settings are used to connect to your ISP.
TD-8816 ADSL2+ Modem Router User Guide Virtual Circuit: Select the VC number you want to setup, PVC0~PVC7. Status: If you want to use a designed VC, you should activate it. VPI: Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255. Please input the value provided by your ISP. VCI: Identifies the virtual channel endpoints in an ATM network. The valid range is from 32 to 65535 (1 to 31 is reserved for well-known protocols).
TD-8816 ADSL2+ Modem Router User Guide Dynamic Route: Select this option to specify the RIP (Routing Information protocol) version for WAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format. Direction: Select this option to specify the RIP direction. None is for disabling the RIP function.
TD-8816 ADSL2+ Modem Router User Guide Figure 4-9 Service name: Specify a name for the PPPoA/PPPoE connection for recognition. Username: Enter your username for your PPPoA/PPPoE connection to identify and verify your account to the ISP. Password: Enter your password for your PPPoA/PPPoE connection. Encapsulation: For both PPPoA/PPPoE connection, you need to specify the type of Multiplexing, either LLC or VC Mux.
TD-8816 4. ADSL2+ Modem Router User Guide Bridge Mode If you select this type of connection, the modem can be configured to act as a bridging device between your LAN and your ISP. Bridges are devices that enable two or more networks to communicate as if they are two segments of the same physical LAN. Figure 4-10 Note: After you finish the Internet configuration, please click SAVE to make the settings take effect. 4.3.
TD-8816 ADSL2+ Modem Router User Guide IP Address: Enter the Router’s local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1. IP Subnet Mask: Enter the Router’s Subnet Mask, the default value is 255.255.255.0. Dynamic Route: Select this option to specify the RIP (Routing Information protocol) version for LAN interface, including RIP1, RIP2-B and RIP2-M.
TD-8816 ADSL2+ Modem Router User Guide IP Pool Count: The max user pool size. Lease Time: The length of time for the IP lease. After the dynamic IP address has expired, the user will be automatically assigned a new dynamic IP address. The default is 259200 seconds. DNS Relay: If you want to disable this feature, you just need to set both Primary and secondary DNS IP to 0.0.0.0. If you want to use DNS relay, you can setup DNS server IP to 192.168.1.1 on their Computer.
TD-8816 4.4 ADSL2+ Modem Router User Guide Advanced Setup Choose “Advanced Setup”, you can see the next submenus: Figure 4-14 Click any of them, and you will be able to configure the corresponding function. 4.4.1 Firewall Choose “Advanced Setup→Firewall” menu, and you will see the next screen (shown in Figure 4-15). Figure 4-15 Firewall: Select this option can automatically detect and block Denial of Service (DoS) attacks, such as Ping of Death, SYN Flood, Port Scan and Land Attack.
TD-8816 ADSL2+ Modem Router User Guide Click ADD ROUTE button to add a new route in the next screen (shown in Figure 4-17). Figure 4-17 Destination IP Address: This parameter specifies the IP network address of the final destination. IP Subnet Mask: Enter the subnet mask for this destination. Gateway IP Address: Enter the IP address of the gateway. The gateway is an immediate neighbor of your ADSL Router that will forward the packet to the destination.
TD-8816 ADSL2+ Modem Router User Guide Virtual Circuit: Enter Virtual Circuit Index that you plan to setup for the NAT function. NAT Status: This field shows the current status of the NAT function for the current VC. You can go to the previous screen (shown in Figure 4-6) to activate the function. Number of IPs; This field is to specify how many IPs are provided by your ISP for current VC. It can be single IP or multiple IPs. We select Multiple to explain.
TD-8816 ADSL2+ Modem Router User Guide Figure 4-20 Rule Index: The Virtual server rule index for this VC. You can specify 10 rules in maximum. All the VCs with single IP will use the same Virtual Server rules. Start & End port number: Enter the specific Start and End Port number you want to forward. If it is one port only, you can enter the End port number the same as Start port number. For example, you want to set the FTP Virtual server, you can set the start and end port number to 21.
TD-8816 ADSL2+ Modem Router User Guide Figure 4-21 Figure 4-22 Rule Index: Select the Virtual server rule index for this VC. You can specify 10 rules in maximum. All the VCs with single IP will use the same Virtual Server rules. Rule Typ: There are four types of one-to-one, Many-to-One, Many-to-Many Overload and Many-to-Many No-overload. Local Start & End IP: Enter the local IP Address you plan to mapped to.
TD-8816 ADSL2+ Modem Router User Guide Step 3: Select the rule type you want from the drop-down list. Step 4: Enter the local and public IP addresses in the corresponding fields. Step 5: After that, click SAVE to make the entry take effect. Other configurations for the entries as shown in Figure 4-22: Enter the index of assigned entry, click the DELETE button to delete the entry. Click the BACK button to return to the previous screen.
TD-8816 ADSL2+ Modem Router User Guide QoS: Select this option to Activated/Deactivated the IP QoS on different types (IP ToS and DiffServ). Summary: Click the button to view the configurations of QoS. Rule: Configure the rules for QoS. If the traffic complies with the rule, then the Router will take the corresponding action to deal with it. Rule Index: Select the index for the rule you want to configure. Active: Activate the rule. The rule can take effect only when it is activated.
TD-8816 ADSL2+ Modem Router User Guide Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization.
TD-8816 ADSL2+ Modem Router User Guide VLAN ID: This indicates the VLAN group. ATM VCs: Select the ATM VCs as members of VLAN, and if you leave the Tagged blank, the tag in frames will be deleted when transmitted from the VC. Ethernet: Select the Ethernet port as a member of VLAN, and if you leave the Tagged blank, the tag in frames will be deleted when transmitted from the port. VLAN Group Summary: This displays the information about the VLAN Groups. 2.
TD-8816 ADSL2+ Modem Router User Guide Figure 4-27 ADSL Mode: Select the ADSL operation mode which your ADSL connection uses. ADSL Type: Select the ADSL operation type which your ADSL connection uses. 4.5 Access Management Choose “Access Management”, you can see the next submenus: Figure 4-28 Click any of them, and you will be able to configure the corresponding function. 4.5.1 ACL Choose “Access Management→ACL”, you can see the next screen (shown in Figure 4-29).
TD-8816 ADSL2+ Modem Router User Guide ACL: If Activated, the IP addresses which are contained in the Access Control List can access to the Router. If Deactivated, all IP addresses can access to the Router. ACL Rule Index: Select the ACL rule index for the entry. Active: Enable the ACL rule. Secure IP Address: Select the IP addresses which are permitted to access to the Router remotely. With the default IP 0.0.0.0, any client would be allowed to remotely access the ADSL Router.
TD-8816 ADSL2+ Modem Router User Guide Figure 4-30 Filter Type Selection: Select the filter type for the next configuration. IP/MAC Filter Set Index: Select the Set index for the IP Filter entry. This index can match with six IP / MAC Filter Rule Indexes. Interface: Select the interface for the entry. Direction: Select the direction for this IP Filter rule. There are three filtering directions: Both, Incoming, Outgoing.
TD-8816 ADSL2+ Modem Router User Guide Rule Type: For IP Filter, please select IP here. Active: Select “Yes” to make the rule to take effect. Source IP Address: Enter the source IP address for the rule. You can enter 0.0.0.0; it means that all IP addresses are controlled by the rule. Subnet Mask: Enter the Subnet Mask for the rule. Port Number: Enter the Port Number for the rule. You can enter 0, it means that all ports are controlled by the rule.
TD-8816 ADSL2+ Modem Router User Guide Step 4: Select the Protocol as “TCP” and select the Unmatched rule as “Next”. Step 5: Finally, click the SAVE to save the entry. Step 6: Go to Step 2 to configure the next two rules: Block E-mail received by the IP address 192.168.1.7 on your local network; Make the PC with IP address 192.168.1.8 unable to visit the website of IP address 202.96.134.12. Note: After you complete the IP filter rules for the example, the Filter list will show as follows.
TD-8816 ADSL2+ Modem Router User Guide Figure 4-31 Rule Type: Select MAC for the MAC Filter rule. Active: Select “Yes” to make the rule to take effect. MAC Address: Enter the MAC address for the rule. Rule Unmatched: If the current rule can not match, and you select Forward, the router will skip the rule and transmit directly. If you select Next, the router will find the next filter rule (show in Filter list) to match.
TD-8816 ADSL2+ Modem Router User Guide Note: If you want to make the rule take effect, please select Yes to active the rule. Step 3: Enter the “MAC Address” and select the Unmatched rule as “Next”. Step 4: Finally, click the SAVE to save the entry. Step 5: Go to Step 2 to configure the next rule: Block the PC with MAC address 00-0A-EB-00-07-5F to access the Internet. Note: After you complete the MAC filter rules for the example, the Filter list will show as follows.
TD-8816 ADSL2+ Modem Router User Guide Figure 4-32 Filter Type Selection: Select the Application Filter for the next configuration. Application Filter: Activate or deactivate the function. ICQ & MSN & YMSG & Real Audio/Video: Select Allow or Deny for these applications. If you select Allow, the Router will accept the application; if you select Deny, the Router will forbid the application. 4.5.2.4.
TD-8816 ADSL2+ Modem Router User Guide Filter Type Selection: Select the URL Filter for the next configuration. Active: Select “Yes” to make the rule to take effect. URL Index: Select the index for the URL Filter entry. URL: Enter the URL for this URL Filter. URL Filter Listing: This displays the information about the URL Filter rules. To add a URL filter entry: For example: If you want to forbid the user to access the website: www.yahoo.com.
TD-8816 ADSL2+ Modem Router User Guide simple peer-to-peer network connectivity between devices. An UPnP device can dynamically join a network, obtain an IP address, convey its capabilities and learn about other devices on the network. In turn, a device can leave a network smoothly and automatically when it is no longer in use. UPnP broadcasts are only allowed on the LAN. Figure 4-35 UPnP: Activate or Deactivate the UPnP function. Only when the function is activated, can the UPnP take effect.
TD-8816 ADSL2+ Modem Router User Guide 4.5.6 CWMP Choose “Access Management→CWMP”, you can configure the CWMP function in the screen (shown in Figure 4-37). The router offers CWMP feature. The function supports TR-069 protocol which collects information, diagnoses the devices and configures the devices automatically via ACS (Auto-Configuration Server). Figure 4-37 CWMP: Select activate the CWMP function. URL: Enter the website of ACS which is provided by your ISP.
TD-8816 ADSL2+ Modem Router User Guide 4.6.1 Administration Choose “Maintenance→Administration”, you can set new password for admin in the screen (shown in Figure 4-39). Figure 4-39 Note: 1) 2) There is only one account that can access Web-Management interface. The default account is "admin", and the password is "admin". Admin has read/write access privilege. When you change the password, you should enter the new password twice, and then click SAVE to make the new password take effect. 4.6.
TD-8816 ADSL2+ Modem Router User Guide Figure 4-40 Note: The ADSL Router built-in some NTP Servers, when the Router connects to the Internet, the Router will get the system time automatically from the NTP Server. You can also configure the NTP Server address automatically, and then the Router will get the time from the specific Server firstly. 2. PC’s Clock Select PC’s Clock as the Synchronize time, you don’t need to set any items. Figure 4-41 3.
TD-8816 ADSL2+ Modem Router User Guide Figure 4-42 4.6.3 Firmware Choose “Maintenance→Firmware”, you can upgrade the firmware of the Router in the screen (shown in Figure 4-43). Make sure the firmware or romfile you want to use is on the local hard drive of the computer. Click Browse to find the local hard drive and locate the firmware or romfile to be used for upgrade.
TD-8816 2) ADSL2+ Modem Router User Guide When you upgrade the router's firmware, you may lose its current configurations, so please back up the router’s current settings before you upgrade its firmware. 3) Do not turn off the router or press the Reset button while the firmware is being upgraded. 4) The router will reboot after the upgrading has been finished.
TD-8816 ADSL2+ Modem Router User Guide 4.6.4 SysRestart Choose “Maintenance→SysRestart”, you can select to restart the device with current settings or restore to factory default settings in the screen (shown in Figure 4-46). Figure 4-46 4.6.5 Diagnostics Choose “Maintenance→Diagnostics”, you can view the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides in the screen (shown in Figure 4-47). Figure 4-47 4.
TD-8816 ADSL2+ Modem Router User Guide Figure 4-48 Note: Click the tab, and you will be able to get the corresponding information.
TD-8816 ADSL2+ Modem Router User Guide Appendix A: Specifications General ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5 Standards and Protocols IEEE 802.3, IEEE 802.3u, TCP/IP, PPPoA , PPPoE, SNTP, HTTP, DHCP, ICMP, NAT,CWMP Safety & Emission Ports LEDs FCC, CE 1 10/100M Auto-Negotiation RJ45 port（Auto MDI/MDIX) 1 RJ11 port Power, LAN, ADSL, Internet 10Base-T: UTP category 3, 4, 5 cable Network Medium 100Base-TX: UTP category-5 Max line length: 6.
TD-8816 ADSL2+ Modem Router User Guide Appendix B: Troubleshooting T1. How do I restore my Router’s configuration to its factory default settings? With the Router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it. Note: Once the Router is reset, the current configuration settings will be lost and you will need to reconfigure the router. T2.
TD-8816 Click Network Connections Right-click Local Area Connection Click Properties 51 ADSL2+ Modem Router User Guide
TD-8816 Double-click Internet Protocol (TCP/IP) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 52 ADSL2+ Modem Router User Guide
TD-8816 Click OK 53 ADSL2+ Modem Router User Guide
TD-8816 For Windows Vista OS Go to Start > Settings >Control Panel, and then you will see the following page.
TD-8816 Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 55 ADSL2+ Modem Router User Guide
TD-8816 For Windows 7 OS Go to Start > Settings > Control Panel, and then you will see the following page.
TD-8816 Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 57 ADSL2+ Modem Router User Guide
TD-8816 ADSL2+ Modem Router User Guide 2) Configure your IE browser Open your IE browser, click Tools tab and you will see the following screen. Click Internet Options Select Never dial a connection Click OK Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your Router’s factory default settings and reconfigure your Router following the instructions in 3.2 Login.
TD-8816 ADSL2+ Modem Router User Guide if you can access the Internet. If the problem persists, please go to the next step. 3) Consult your ISP and make sure all the VPI/VCI, Connection Type, account username and password are correct. If there are any mistakes, please correct the settings and try again. 4) If you still cannot access the Internet, please restore your Router to its factory default settings and reconfigure your Router by following the instructions in 3.2 Login.
TD-8816 ADSL2+ Modem Router User Guide Appendix C: Technical Support Technical Support For more troubleshooting help, go to: www.tp-link.com/en/support/faq To download the latest Firmware, Driver, Utility and User Guide, go to: www.tp-link.com/en/support/download For all other technical support, please contact us by using the following details: Global Tel: +86 755 2650 4400 Fee: Depending on rate of different carriers, IDD. E-mail: support@tp-link.
