User Manual Robot Vacuum & Mop *Images may differ from acual products. ©2023 TP-Link 7106510061 REV1.2.
IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE WARNING – To reduce the risk of fire, electric shock, or injury: • Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. • Do not use outdoors or on wet surfaces. • Do not allow to be used as a toy. Close attention is necessary when used by or near children. • Use only as described in this manual. Use only manufacturer’s recommended attachments. • Do not use with damaged cord or plug.
• Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. • Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. • Do not use a battery pack or appliance that is damaged or modified.
The original UK declaration of conformity may be found at https://www.tapo.com/support/ukca/ Safety Information Keep the device away from water, fire, humidity or hot environments. This appliance contains batteries that are only replaceable by skilled persons. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. Warning Avoid replacement of a battery with an incorrect type that can defeat a safeguard.
Package Contents Charging Dock ×1 + Power Adapter x1 Robot Vacuum* HEPA Filter ×1 *One side brush and HEPA filter installed User Manual Side Brush ×1 Mop Cloth Mount* ×1 *One washable mop cloth installed 1 User Manual ×1 Cleaning Brush ×1
Overview Power/Clean • Press once: Start/pause cleaning. Robot Vacuum • Press and hold for 5 seconds: Turn on/off the robot vacuum. *For the first use, slide the power switch from OFF to ON to turn on. Dock • Return to the dock to charge. Spot Cleaning/Child Lock • Press once: Start spot cleaning. • Press and hold for 5 seconds: Turn on/off the child lock. Combination Button • Press and hold simultaneously for 5 seconds: Enter setup mode to configure network.
Buttons & LEDs Dustbin Latch Cover Rubber Plug Recharge Sensor Water Tank Latch OFF Bumper OFF ON ON Power Switch Dustbin & Water Tank Filter Dustbin Cliff Sensors Water Tank Caster Wheel Open Dustbin Side Brush Charging Contacts LED Indicator Wheel Main Brush Main Brush Cover Latch Charging Contacts Charging Dock 3
1 Position the Dock 2 Remove Protective Strip 1. Remove the bottom cover of the dock, connect the power cord to the dock, and then replace the cover. 1 Before use, remove the protective strips on both sides of the front bumper. 2 2. Place the dock on a level surface, flat against a wall, without obstacles within 1.5m (4.9ft) in front and 0.5m (1.6ft) on left and right. 3 Remove Protective Film 0.5 m (1 .6ft ) 9f m 1.5 (4. t) 0.5m Remove the protective film on the front bumper. (1.
4 Power On and Charge Slide the power switch from OFF to ON to turn on your robot vacuum. Place the robot vacuum on the charging dock or tap to send it back to the dock to charge. It will return to the dock at the end of a cleaning job and whenever it needs to recharge. Notes • If the power switch is in the ON position, you can also press and hold the button for 5 seconds to turn on/off your robot vacuum.
5 Download the Tapo App and Connect to Wi-Fi In the Tapo app, you can enjoy the following functions. 1. Download the Tapo app from the App Store or Google Play, then log in. • Cleaning Modes & Preferences Customize vacuum power, water level, and cleaning times. OR • Scheduled Cleaning Set an automatic cleaning schedule, then the robot vacuum will clean automatically at the set time and return to the dock after cleaning. 2. Open the Tapo app, tap + icon, and select your model.
6 Cleaning The robot vacuum will automatically explore and clean your home in neat rows. It will return to the charging station at the end of a cleaning job and whenever it needs to recharge. Press Once Press Once Start/pause cleaning. Start spot cleaning. In Spot Cleaning mode, it will sweep the circular area with a diameter of 1.5m (4.9ft) calculated from its own position. Notes • Cleaning cannot start if the battery is too low. Charge your robot vacuum first.
• Vacuum floors at least 3 times before the first mopping cycle. • The ability to cross obstacles is reduced when mopping. • It is recommended to wash the mop cloth after each use. 7 Mopping 1. Take out the dustbin and water tank. 1. Remove the mop cloth mount. OFF ON 2. Remove the rubber plug and add up to 300ml of water to the water tank. 2. Empty the water tank. • Fill with cool/room temperature water only. Be careful not to wet the metal contacts. • Use only cleaning agents specified by Tapo.
8 Care and Maintenance To maintain optimal performance, maintain the robot vacuum according to the following guidelines.
Empty the Bin Clean the Filter 1. Remove the dustbin and water tank. 1. Remove the dustbin and open the lid. OFF 2. Remove the filter. ON 2. Open the dustbin to empty the dustbin. 3. Clean the filter with a cleaning brush. 4. Wash the dustbin and filter. Do not wash with hot water or detergents. 3. Place the dustbin back inside the robot vacuum. 5. Air-dry the dustbin and filter thoroughly, then install the filter in the previous orientation.
Clean the Main Brush Clean the Side Brush 1. Turn the robot vacuum over, then unlatch and remove the main brush cover. 1. Pull firmly to remove the side brush and remove any entangled debris. Wipe with a damp cloth if needed. 2. Re-install the side brush and press it tightly to ensure it is installed in place. 2. Remove the brush and its end cap. 3. Remove any hair or debris with the cleaning brush. 4. Re-install the cap and main brush. Press on the main brush cover to lock it in place.
Clean the Caster Wheel Clean Main Wheels 1. Pull firmly to remove the caster wheel and remove hair or dirt. Wipe main wheels with a clean, dry cloth. 2. Re-install the caster wheel and press it firmly in place.
Clean the Sensors Clean the Charging Contacts Wipe the sensors with a clean, dry cloth. Wipe the charging contacts with a clean, dry cloth.
9 Troubleshooting Issues Solution Setup failure 1. Check if the power switch on the left side of the robot vacuum is toggled to “ON”. 2. The battery level is low. Please place the robot vacuum on the dock to charge and it will start automatically when it is ready. 3. Check your internet connection or check if you have configured Allow List or Firewall settings on your router. Charging failure 1.
Issues Solution Failure to connect to Wi-Fi 1. The Wi-Fi signal is poor. Please make sure the robot vacuum is in an area with good Wi-Fi signals. 2. Wi-Fi connection is abnormal. Please reset the Wi-Fi and download the latest app and try again. 3. The password is entered incorrectly. Please check. 4. The robot vacuum only supports the 2.4 GHz frequency band. Please connect to a 2.4 GHz Wi-Fi. Scheduled cleaning doesn’t work 1. The battery level is low.
Energy Saving Mode When the robot vacuum is docked, press and hold the Power button and the Dock button until you hear an alert sound. It will also enter the Energy Saving mode when it is fully charged. for about 15 seconds In this mode, only the charging feature will work. Other functions will not work, such as LEDs will be off, sensors will not work, and Wi-Fi will be disconnected. To exit the Energy Saving mode, press any button on the robot vacuum. ? Need some help? Visit www.tapo.
