Operation Manual

ManualsBrandsTP-LINK ManualsComputersT2500-28TC-TL-SL5428E

Table Of Contents

Package Contents
Chapter 1 About This Guide
- 1.1 Intended Readers
- 1.2 Conventions
- 1.3 Overview of This Guide
Chapter 2 Introduction
- 2.1 Overview of the Switch
- 2.2 Appearance Description
  - 2.2.1 Front Panel
  - 2.2.2 Rear Panel
Chapter 3 Login to the Switch
- 3.1 Login
- 3.2 Configuration
Chapter 4 System
- 4.1 System Info
- 4.2 User Management
  - 4.2.1 User Table
  - 4.2.2 User Config
- 4.3 System Tools
- 4.4 Access Security
Chapter 5 Switching
- 5.1 Port
- 5.2 DDM
- 5.3 LAG
- 5.4 Traffic Monitor
  - 5.4.1 Traffic Summary
  - 5.4.2 Traffic Statistics
- 5.5 MAC Address
Chapter 6 VLAN
- 6.1 802.1Q VLAN
  - 6.1.1 VLAN Config
  - 6.1.2 Port Config
- 6.2 MAC VLAN
  - 6.2.1 MAC VLAN
  - 6.2.2 Port Enable
- 6.3 Protocol VLAN
- 6.4 Application Example for 802.1Q VLAN
- 6.5 Application Example for MAC VLAN
- 6.6 Application Example for Protocol VLAN
- 6.7 VLAN VPN
- 6.8 Private VLAN
  - 6.8.1 PVLAN Config
  - 6.8.2 Port Config
- 6.9 GVRP
- 6.10 Application Example for Private VLAN
Chapter 7 Spanning Tree
- 7.1 STP Config
  - 7.1.1 STP Config
  - 7.1.2 STP Summary
- 7.2 Port Config
- 7.3 MSTP Instance
- 7.4 STP Security
  - 7.4.1 Port Protect
  - 7.4.2 TC Protect
- 7.5 Application Example for STP Function
Chapter 8 Ethernet OAM
- 8.1 Basic Config
  - 8.1.1 Basic Config
  - 8.1.2 Discovery Info
- 8.2 Link Monitoring
- 8.3 RFI
- 8.4 Remote Loopback
- 8.5 Statistics
  - 8.5.1 Statistics
  - 8.5.2 Event Log
- 8.6 DLDP
- 8.7 Application Example for DLDP
Chapter 9 DHCP
- 9.1 DHCP Relay
Chapter 10 Multicast
- 10.1 IGMP Snooping
- 10.2 MLD Snooping
- 10.3 Multicast Table
  - 10.3.1 IPv4 Multicast Table
  - 10.3.2 IPv6 Multicast Table
Chapter 11 QoS
- 11.1 DiffServ
- 11.2 Bandwidth Control
  - 11.2.1 Rate Limit
  - 11.2.2 Storm Control
- 11.3 Voice VLAN
Chapter 12 ACL
- 12.1 Time-Range
- 12.2 ACL Config
- 12.3 Policy Config
- 12.4 Policy Binding
- 12.5 Application Example for ACL
Chapter 13 Network Security
- 13.1 IP-MAC Binding
- 13.2 DHCP Snooping
  - 13.2.1 DHCP Snooping
  - 13.2.2 Option 82
- 13.3 ARP Inspection
- 13.4 IP Source Guard
- 13.5 DoS Defend
  - 13.5.1 DoS Defend
  - 13.5.2 DoS Detect
- 13.6 802.1X
  - 13.6.1 Global Config
  - 13.6.2 Port Config
- 13.7 AAA
- 13.8 PPPoE Config
Chapter 14 SNMP
- 14.1 SNMP Config
- 14.2 Notification
  - 14.2.1 Notification Config
  - 14.2.2 Traps Config
- 14.3 RMON
Chapter 15 LLDP
- 15.1 Basic Config
  - 15.1.1 Global Config
  - 15.1.2 Port Config
- 15.2 Device Info
  - 15.2.1 Local Info
  - 15.2.2 Neighbor Info
- 15.3 Device Statistics
- 15.4 LLDP-MED
Chapter 16 Cluster
- 16.1 NDP
- 16.2 NTDP
- 16.3 Cluster
Chapter 17 Maintenance
- 17.1 System Monitor
  - 17.1.1 CPU Monitor
  - 17.1.2 Memory Monitor
- 17.2 Log
- 17.3 Device Diagnostics
- 17.4 Network Diagnostics
  - 17.4.1 Ping
  - 17.4.2 Tracert
Chapter 18 System Maintenance via FTP
Appendix A: Glossary

4.3 System Tools

The System Tools function, allowing you to manage the configuration file of the switch, can be

implemented on Config Restore, Config Backup, Firmware Upgrade, System Reboot and

System Reset pages.

4.3.1 Config Restore

On this page you can upload a backup configuration file to restore your switch to this previous

configuration.

Choose the menu System→System Tools→Config Restore to load the following page.

Figure 4-13 Config Restore

The following entries are displayed on this screen:



Config Restore

Restore Config: Click the Restore Config

button to restore the backup

configuration file. It will take effect after the switch

automatically reboots.

Note:

1. It will take a few minutes to restore the configuration. Please wait without any operation.

2. To avoid any damage, please don’t power down the switch while being restored.

3. After being restored, the current settings of the switch will be lost. Wrong uploaded

configuration file may cause the switch unmanaged.

4.3.2 Config Backup

On this page you can download the current configuration and save it as a file to your computer

for your future configuration restore.

Choose the menu System→System Tools→Config Backup to load the following page.