Operation Manual

ManualsBrandsTP-LINK ManualsComputersT2500-28TC-TL-SL5428E

311

312

313

314

315

316

317

318

319

320

Table Of Contents

Package Contents
Chapter 1 About This Guide
- 1.1 Intended Readers
- 1.2 Conventions
- 1.3 Overview of This Guide
Chapter 2 Introduction
- 2.1 Overview of the Switch
- 2.2 Appearance Description
  - 2.2.1 Front Panel
  - 2.2.2 Rear Panel
Chapter 3 Login to the Switch
- 3.1 Login
- 3.2 Configuration
Chapter 4 System
- 4.1 System Info
- 4.2 User Management
  - 4.2.1 User Table
  - 4.2.2 User Config
- 4.3 System Tools
- 4.4 Access Security
Chapter 5 Switching
- 5.1 Port
- 5.2 DDM
- 5.3 LAG
- 5.4 Traffic Monitor
  - 5.4.1 Traffic Summary
  - 5.4.2 Traffic Statistics
- 5.5 MAC Address
Chapter 6 VLAN
- 6.1 802.1Q VLAN
  - 6.1.1 VLAN Config
  - 6.1.2 Port Config
- 6.2 MAC VLAN
  - 6.2.1 MAC VLAN
  - 6.2.2 Port Enable
- 6.3 Protocol VLAN
- 6.4 Application Example for 802.1Q VLAN
- 6.5 Application Example for MAC VLAN
- 6.6 Application Example for Protocol VLAN
- 6.7 VLAN VPN
- 6.8 Private VLAN
  - 6.8.1 PVLAN Config
  - 6.8.2 Port Config
- 6.9 GVRP
- 6.10 Application Example for Private VLAN
Chapter 7 Spanning Tree
- 7.1 STP Config
  - 7.1.1 STP Config
  - 7.1.2 STP Summary
- 7.2 Port Config
- 7.3 MSTP Instance
- 7.4 STP Security
  - 7.4.1 Port Protect
  - 7.4.2 TC Protect
- 7.5 Application Example for STP Function
Chapter 8 Ethernet OAM
- 8.1 Basic Config
  - 8.1.1 Basic Config
  - 8.1.2 Discovery Info
- 8.2 Link Monitoring
- 8.3 RFI
- 8.4 Remote Loopback
- 8.5 Statistics
  - 8.5.1 Statistics
  - 8.5.2 Event Log
- 8.6 DLDP
- 8.7 Application Example for DLDP
Chapter 9 DHCP
- 9.1 DHCP Relay
Chapter 10 Multicast
- 10.1 IGMP Snooping
- 10.2 MLD Snooping
- 10.3 Multicast Table
  - 10.3.1 IPv4 Multicast Table
  - 10.3.2 IPv6 Multicast Table
Chapter 11 QoS
- 11.1 DiffServ
- 11.2 Bandwidth Control
  - 11.2.1 Rate Limit
  - 11.2.2 Storm Control
- 11.3 Voice VLAN
Chapter 12 ACL
- 12.1 Time-Range
- 12.2 ACL Config
- 12.3 Policy Config
- 12.4 Policy Binding
- 12.5 Application Example for ACL
Chapter 13 Network Security
- 13.1 IP-MAC Binding
- 13.2 DHCP Snooping
  - 13.2.1 DHCP Snooping
  - 13.2.2 Option 82
- 13.3 ARP Inspection
- 13.4 IP Source Guard
- 13.5 DoS Defend
  - 13.5.1 DoS Defend
  - 13.5.2 DoS Detect
- 13.6 802.1X
  - 13.6.1 Global Config
  - 13.6.2 Port Config
- 13.7 AAA
- 13.8 PPPoE Config
Chapter 14 SNMP
- 14.1 SNMP Config
- 14.2 Notification
  - 14.2.1 Notification Config
  - 14.2.2 Traps Config
- 14.3 RMON
Chapter 15 LLDP
- 15.1 Basic Config
  - 15.1.1 Global Config
  - 15.1.2 Port Config
- 15.2 Device Info
  - 15.2.1 Local Info
  - 15.2.2 Neighbor Info
- 15.3 Device Statistics
- 15.4 LLDP-MED
Chapter 16 Cluster
- 16.1 NDP
- 16.2 NTDP
- 16.3 Cluster
Chapter 17 Maintenance
- 17.1 System Monitor
  - 17.1.1 CPU Monitor
  - 17.1.2 Memory Monitor
- 17.2 Log
- 17.3 Device Diagnostics
- 17.4 Network Diagnostics
  - 17.4.1 Ping
  - 17.4.2 Tracert
Chapter 18 System Maintenance via FTP
Appendix A: Glossary

301

Detail

：

Click the Detail button to view

the complete information

collected for the port.

16.1.3 NDP Config

On this page you can configure the NDP function for the switch.

Choose the menu Cluster→NDP→NDP Config to load the following page.

Figure 16-4 NDP Config

The following entries are displayed on this screen:



Global Config

NDP:

Enable/Disable NDP function globally.

Aging Time:

Enter the period for the neighbor switch to keep the NDP

packets from this switch.

Hello Time:

Enter the interval to send NDP packets.



Port Config

Select:

Select the desired port to configure its NDP status.