Operation Manual

ManualsBrandsTP-LINK ManualsComputersT2500-28TC-TL-SL5428E

121

122

123

124

125

126

127

128

129

130

Table Of Contents

Package Contents
Chapter 1 About This Guide
- 1.1 Intended Readers
- 1.2 Conventions
- 1.3 Overview of This Guide
Chapter 2 Introduction
- 2.1 Overview of the Switch
- 2.2 Appearance Description
  - 2.2.1 Front Panel
  - 2.2.2 Rear Panel
Chapter 3 Login to the Switch
- 3.1 Login
- 3.2 Configuration
Chapter 4 System
- 4.1 System Info
- 4.2 User Management
  - 4.2.1 User Table
  - 4.2.2 User Config
- 4.3 System Tools
- 4.4 Access Security
Chapter 5 Switching
- 5.1 Port
- 5.2 DDM
- 5.3 LAG
- 5.4 Traffic Monitor
  - 5.4.1 Traffic Summary
  - 5.4.2 Traffic Statistics
- 5.5 MAC Address
Chapter 6 VLAN
- 6.1 802.1Q VLAN
  - 6.1.1 VLAN Config
  - 6.1.2 Port Config
- 6.2 MAC VLAN
  - 6.2.1 MAC VLAN
  - 6.2.2 Port Enable
- 6.3 Protocol VLAN
- 6.4 Application Example for 802.1Q VLAN
- 6.5 Application Example for MAC VLAN
- 6.6 Application Example for Protocol VLAN
- 6.7 VLAN VPN
- 6.8 Private VLAN
  - 6.8.1 PVLAN Config
  - 6.8.2 Port Config
- 6.9 GVRP
- 6.10 Application Example for Private VLAN
Chapter 7 Spanning Tree
- 7.1 STP Config
  - 7.1.1 STP Config
  - 7.1.2 STP Summary
- 7.2 Port Config
- 7.3 MSTP Instance
- 7.4 STP Security
  - 7.4.1 Port Protect
  - 7.4.2 TC Protect
- 7.5 Application Example for STP Function
Chapter 8 Ethernet OAM
- 8.1 Basic Config
  - 8.1.1 Basic Config
  - 8.1.2 Discovery Info
- 8.2 Link Monitoring
- 8.3 RFI
- 8.4 Remote Loopback
- 8.5 Statistics
  - 8.5.1 Statistics
  - 8.5.2 Event Log
- 8.6 DLDP
- 8.7 Application Example for DLDP
Chapter 9 DHCP
- 9.1 DHCP Relay
Chapter 10 Multicast
- 10.1 IGMP Snooping
- 10.2 MLD Snooping
- 10.3 Multicast Table
  - 10.3.1 IPv4 Multicast Table
  - 10.3.2 IPv6 Multicast Table
Chapter 11 QoS
- 11.1 DiffServ
- 11.2 Bandwidth Control
  - 11.2.1 Rate Limit
  - 11.2.2 Storm Control
- 11.3 Voice VLAN
Chapter 12 ACL
- 12.1 Time-Range
- 12.2 ACL Config
- 12.3 Policy Config
- 12.4 Policy Binding
- 12.5 Application Example for ACL
Chapter 13 Network Security
- 13.1 IP-MAC Binding
- 13.2 DHCP Snooping
  - 13.2.1 DHCP Snooping
  - 13.2.2 Option 82
- 13.3 ARP Inspection
- 13.4 IP Source Guard
- 13.5 DoS Defend
  - 13.5.1 DoS Defend
  - 13.5.2 DoS Detect
- 13.6 802.1X
  - 13.6.1 Global Config
  - 13.6.2 Port Config
- 13.7 AAA
- 13.8 PPPoE Config
Chapter 14 SNMP
- 14.1 SNMP Config
- 14.2 Notification
  - 14.2.1 Notification Config
  - 14.2.2 Traps Config
- 14.3 RMON
Chapter 15 LLDP
- 15.1 Basic Config
  - 15.1.1 Global Config
  - 15.1.2 Port Config
- 15.2 Device Info
  - 15.2.1 Local Info
  - 15.2.2 Neighbor Info
- 15.3 Device Statistics
- 15.4 LLDP-MED
Chapter 16 Cluster
- 16.1 NDP
- 16.2 NTDP
- 16.3 Cluster
Chapter 17 Maintenance
- 17.1 System Monitor
  - 17.1.1 CPU Monitor
  - 17.1.2 Memory Monitor
- 17.2 Log
- 17.3 Device Diagnostics
- 17.4 Network Diagnostics
  - 17.4.1 Ping
  - 17.4.2 Tracert
Chapter 18 System Maintenance via FTP
Appendix A: Glossary

111

increases the network load of the switches and wastes network resources. The default

value is recommended.

3. A too small max age parameter may result in the switches regenerating spanning trees

frequently and cause network congestions to be falsely regarded as link problems. A too

large max age parameter result in the switches unable to find the link problems in time,

which in turn handicaps spanning trees being regenerated in time and makes the network

less adaptive. The default value is recommended.

4. If the TxHold Count parameter is too large, the number of MSTP packets being sent in each

hello time may be increased with occupying too much network resources. The default

value is recommended.

7.1.2 STP Summary

On this page you can view the related parameters for Spanning Tree function.

Choose the menu Spanning Tree→STP Config→STP Summary to load the following page.

Figure 7-5 STP Summary

7.2 Port Config

On this page you can configure the parameters of the ports for CIST