Operation Manual

ManualsBrandsTP-LINK ManualsComputersT2500-28TC-TL-SL5428E

111

112

113

114

115

116

117

118

119

120

Table Of Contents

Package Contents
Chapter 1 About This Guide
- 1.1 Intended Readers
- 1.2 Conventions
- 1.3 Overview of This Guide
Chapter 2 Introduction
- 2.1 Overview of the Switch
- 2.2 Appearance Description
  - 2.2.1 Front Panel
  - 2.2.2 Rear Panel
Chapter 3 Login to the Switch
- 3.1 Login
- 3.2 Configuration
Chapter 4 System
- 4.1 System Info
- 4.2 User Management
  - 4.2.1 User Table
  - 4.2.2 User Config
- 4.3 System Tools
- 4.4 Access Security
Chapter 5 Switching
- 5.1 Port
- 5.2 DDM
- 5.3 LAG
- 5.4 Traffic Monitor
  - 5.4.1 Traffic Summary
  - 5.4.2 Traffic Statistics
- 5.5 MAC Address
Chapter 6 VLAN
- 6.1 802.1Q VLAN
  - 6.1.1 VLAN Config
  - 6.1.2 Port Config
- 6.2 MAC VLAN
  - 6.2.1 MAC VLAN
  - 6.2.2 Port Enable
- 6.3 Protocol VLAN
- 6.4 Application Example for 802.1Q VLAN
- 6.5 Application Example for MAC VLAN
- 6.6 Application Example for Protocol VLAN
- 6.7 VLAN VPN
- 6.8 Private VLAN
  - 6.8.1 PVLAN Config
  - 6.8.2 Port Config
- 6.9 GVRP
- 6.10 Application Example for Private VLAN
Chapter 7 Spanning Tree
- 7.1 STP Config
  - 7.1.1 STP Config
  - 7.1.2 STP Summary
- 7.2 Port Config
- 7.3 MSTP Instance
- 7.4 STP Security
  - 7.4.1 Port Protect
  - 7.4.2 TC Protect
- 7.5 Application Example for STP Function
Chapter 8 Ethernet OAM
- 8.1 Basic Config
  - 8.1.1 Basic Config
  - 8.1.2 Discovery Info
- 8.2 Link Monitoring
- 8.3 RFI
- 8.4 Remote Loopback
- 8.5 Statistics
  - 8.5.1 Statistics
  - 8.5.2 Event Log
- 8.6 DLDP
- 8.7 Application Example for DLDP
Chapter 9 DHCP
- 9.1 DHCP Relay
Chapter 10 Multicast
- 10.1 IGMP Snooping
- 10.2 MLD Snooping
- 10.3 Multicast Table
  - 10.3.1 IPv4 Multicast Table
  - 10.3.2 IPv6 Multicast Table
Chapter 11 QoS
- 11.1 DiffServ
- 11.2 Bandwidth Control
  - 11.2.1 Rate Limit
  - 11.2.2 Storm Control
- 11.3 Voice VLAN
Chapter 12 ACL
- 12.1 Time-Range
- 12.2 ACL Config
- 12.3 Policy Config
- 12.4 Policy Binding
- 12.5 Application Example for ACL
Chapter 13 Network Security
- 13.1 IP-MAC Binding
- 13.2 DHCP Snooping
  - 13.2.1 DHCP Snooping
  - 13.2.2 Option 82
- 13.3 ARP Inspection
- 13.4 IP Source Guard
- 13.5 DoS Defend
  - 13.5.1 DoS Defend
  - 13.5.2 DoS Detect
- 13.6 802.1X
  - 13.6.1 Global Config
  - 13.6.2 Port Config
- 13.7 AAA
- 13.8 PPPoE Config
Chapter 14 SNMP
- 14.1 SNMP Config
- 14.2 Notification
  - 14.2.1 Notification Config
  - 14.2.2 Traps Config
- 14.3 RMON
Chapter 15 LLDP
- 15.1 Basic Config
  - 15.1.1 Global Config
  - 15.1.2 Port Config
- 15.2 Device Info
  - 15.2.1 Local Info
  - 15.2.2 Neighbor Info
- 15.3 Device Statistics
- 15.4 LLDP-MED
Chapter 16 Cluster
- 16.1 NDP
- 16.2 NTDP
- 16.3 Cluster
Chapter 17 Maintenance
- 17.1 System Monitor
  - 17.1.1 CPU Monitor
  - 17.1.2 Memory Monitor
- 17.2 Log
- 17.3 Device Diagnostics
- 17.4 Network Diagnostics
  - 17.4.1 Ping
  - 17.4.2 Tracert
Chapter 18 System Maintenance via FTP
Appendix A: Glossary

109

The following diagram shows the different port roles.

Figure 7-3 Port roles

The Spanning Tree module is mainly for spanning tree configuration of the switch, including

four submenus: STP Config, Port Config, MSTP Instance and STP Security.

7.1 STP Config

The STP Config function, for global configuration of spanning trees on the switch, can be

implemented on STP Config and STP Summary pages.

7.1.1 STP Config

Before configuring spanning trees, you should make clear the roles each switch plays in each

spanning tree instance. Only one switch can be the root bridge in each spanning tree instance.

On this page you can globally configure the spanning tree function and related parameters.

Choose the menu Spanning Tree→STP Config→STP Config to load the following page.

Figure 7-4 STP Config